Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for DeWalt D28011
Summary of Contents for DeWalt D28011
- Page 1 D28011 D28111 D28113 D28130 D28134 D28135 D28139 D28141 www.
- Page 2 Dansk (oversat fra original brugsvejledning) Deutsch (übersetzt von den Originalanweisungen) English (original instructions) Español (traducido de las instrucciones originales) Français (traduction de la notice d’instructions originale) Italiano (tradotto dalle istruzioni originali) Nederlands (vertaald vanuit de originele instructies) Norsk (oversatt fra de originale instruksjonene) Português (traduzido das instruções originais) Suomi (käännetty alkuperäisestä...
- Page 3 Figure 1 D28113/D28130/D28134/ D28135/D28141...
- Page 4 Figure 2 Figure 3 Figure 4 Figure 5...
- Page 5 Figure 6...
-
Page 6: Technical Data
EN GLI SH ANGLE GRINDERS D28011, D28111, D28113, D28130, D28134, D28135, D28139, D28141 Congratulations! You have chosen a D WALT tool. Years of experience, thorough product development and innovation make WALT one of the most reliable partners for professional power tool users. -
Page 7: Defi Nitions: Safety Guidelines
EN GL IS H D28134 D28135 D28139 D28141 Voltage U.K. & Ireland only – 230/115 – – Type Power input 1100 1400 1400 No-load/rated speed 10500 10500 10500 9000 Wheel diameter Spindle diameter Spindle length Weight 2.2* 2.5* 2.1* 2.6* * weight includes side handle and guard (sound pressure) dB(A) -
Page 8: Ec Declaration Of Conformity
2) ELECTRICAL SAFETY Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed D28011/D28111/D28113/D28130/D28134/D28135/ (grounded) power tools. Unmodified plugs D28139/D28141 and matching outlets will reduce risk of WALT declares that these products described electric shock. -
Page 9: Additional Specific Safety Rules
EN GL IS H Use personal protective equipment. breakage of parts and any other condition Always wear eye protection. Protective that may affect the power tool’s operation. equipment such as dust mask, non-skid If damaged, have the power tool repaired safety shoes, hard hat, or hearing protection before use. -
Page 10: Further Safety Instructions For All Operations
EN GLI SH with arbour holes that do not match the n) Regularly clean the power tool’s air vents. mounting hardware of the power tool will run The motor’s fan will draw the dust inside out of balance, vibrate excessively and may the housing and excessive accumulation of cause loss of control. -
Page 11: Safety Warnings Specifi C For Sanding Operations
EN GL IS H d) Use special care when working corners, your body, the possible kickback may propel the sharp edges etc. Avoid bouncing and spinning wheel and the power tool directly at snagging the accessory. Corners, sharp you. edges or bouncing have a tendency to snag the c) When wheel is binding or when interrupting rotating accessory and cause loss of control or a cut for any reason, switch off the power... -
Page 12: Additional Safety Information
– Risk of personal injury due flying particles. – Risk of burns due to accessories becoming hot INTENDED USE during operation. The D28011/D28111/D28113/D28130/D28134/ – Risk of personal injury due to prolonged use. D28135/D28139/D28141 heavy-duty angle grinders have been designed for professional grinding, cutting –... -
Page 13: Electrical Safety
• Connect the brown lead to the live terminal in this grinder. the plug. When using the D28011, D28111, D28113, • Connect the blue lead to the neutral terminal. D28130, D28134, D28135, D28139 or the D28141 WARNING: No connection is to be grinder with a bonded abrasive wheel for cutting made to the earth terminal. -
Page 14: Prior To Operation
EN GLI SH CAUTION: If the guard cannot be Fitting and Removing a tightened by the adjusting screw, do Backing Pad/Sanding Sheet not use the tool. To reduce the risk of (fi g. 1, 5) personal injury, take the tool and guard to a service centre to repair or replace 1. -
Page 15: Operation
EN GL IS H OPERATION • Do not use separate reducing bushings or adapters to adapt large hole abrasive wheels. Instructions for Use • Never use the tool without the guard WARNING: Always observe the safety in place. instructions and applicable regulations. •... -
Page 16: Maintenance
EN GLI SH To engage the lock, depress the spindle lock button machine back and forth with moderate pressure. In and rotate the spindle until you are unable to rotate this manner, the workpiece will not become too hot, the spindle further. does not discolour and no grooves are formed. -
Page 17: Optional Accessories
EN GL IS H Protecting the Environment Separate collection. This product must not be disposed of with normal Cleaning household waste. WARNING: Blow dirt and dust out of the main housing with dry air as often as Should you find one day that your D WALT product dirt is seen collecting in and around the needs replacement, or if it is of no further use to you,... - Page 18 EN GLI SH GUARANTEE WALT is confident of the quality of its products and offers an outstanding guarantee for professional users of the product. This guarantee statement is in addition to and in no way prejudices your contractual rights as a professional user or your statutory rights as a private non-professional user.
- Page 19 EN GL IS H GRINDING AND CUTTING ACCESSORY CHART Guard Type Accessory Description How to Fit Grinder Depressed centre grinding disc TYPE 27 Type 27 guard GUARD Flap wheel Backing flange Wire wheels Type 27 depressed centre wheel Threaded clamp nut Wire wheels with threaded Type 27 guard...
- Page 20 EN GLI SH GRINDING AND CUTTING ACCESSORY CHART (cont.) Guard Type Accessory Description How to Fit Grinder Masonry cutting disc, bonded TYPE 1 Type 1 guard GUARD Metal cutting disc, Backing flange bonded Diamond Cutting wheel cutting wheels TYPE 1 Threaded clamp nut GUARD TYPE 27...