リモコン(1) 各部の名称と働き カメラ本体 前面 取扱説明書(1) A レンズ 光学 10 倍ズームレンズです。 B リモコン受光部 付属のリモコンの受光部です。 C POWER ランプ AC 電源アダプターと電源コードを 使って本機をコンセントにつなぐ と、点灯します。 付属リモコンからの操作を受信する と、緑色が点滅してお知らせしま す。 D STANDBY ランプ リモコンで電源を切ると、点灯しま す。 各部の名称と働き...
I SD OUT VIDEO 端子 背面 本機からの映像をアナログコンポ ジット信号として出力します。 J SD OUT S VIDEO 端子 本機からの映像を S ビデオ信号とし て出力します。 K HD OUT COMPONENT 端子 本機からの映像をアナログコンポー ネント信号(YPbPr)として出力し ます。 L HD OUT HD-SDI 端子 E DC IN 12V 端子 本機からの映像を HD-SDI 信号 付属の AC 電源アダプターを接続し (SMPTE292M シリアルデジタルイ...
SQ:SQUEESE の略。アスペクト比 16:9 リモコン のモニターで歪みのない画像となるよう に水平方向に圧縮した画像を出力する。 BOTTOM スイッチの設定 A スイッチ1 (IR OUT スイッチ) ON にすると VISCA IN 端子(44 ページ)から赤外線リモコンの受信 信号が出力され、OFF にすると出 力されません。 B スイッチ2 ( 通信ボーレート切り 換えスイッチ) A CAMERA SELECT ボタン ON にすると VISCA 通信のボー リモコンで操作したいカメラの番号 レートが 38400bps になり、OFF に を押します。カメラ番号は、カメラ...
メッセージ リモコンでの操作 SYSTEM メニュー One Push WB : ワンプッシュオートホ ワイトバランスが実行 されているときに点滅 で表示。 One Push WB : ワンプッシュオートホ ワイトバランスが正常 に終了したとき点灯で 表示。 One push WB : ワンプッシュオートホ ワイトバランスが失敗 IR-RECEIVE(赤外線受光) したときに点滅で表 示。 OFF にすると、付属のリモコンの信号 を受け付けなくなります。 SYNC TYPE 付属のリモコンを使うときは、必ず HD OUT COMPONENT 端子からの同 ON にしてください。 期信号を切り替えます。...
コンポジットビデオ入力端子、 HD-SDI 入力端子を持つ VTR S ビデオ入力端子を持つビデオ などとの接続 モニターや VTR との接続 HD OUT 電源コンセントへ HD-SDI SD OUT SD OUT 電源コン VIDEO S VIDEO セントへ BNC コネクター 付き接続ケーブル (別売り) ビデオ接続 S 映像ケーブル ケーブル (別売り) (別売り) HD-SDI 入力端子へ コンポジット S ビデオ ビデオ端子へ 端子へ HD-SDI 入力端子のある...
Page 46
When installing the unit, incorporate a For the customers in Europe readily accessible disconnect device in the The manufacturer of this product is Sony fixed wiring, or connect the power plug to an Corporation, 1-7-1 Konan, Minato-ku, easily accessible socket-outlet near the unit.
Page 47
Sony. Einrichtung kann im Wohnbereich Funkstörungen verursachen; in diesem Fall Pour les clients en Europe kann vom Betreiber verlangt werden, Le fabricant de ce produit est Sony angemessene Maßnahmen durchzuführen Corporation, 1-7-1 Konan, Minato-ku, und dafür aufzukommen. Tokyo, Japon.
Page 48
Table of Contents Panning and Tilting ....66 Getting Started Zooming ........67 Precautions ........49 Operating Multiple Cameras with the Remote Commander . 68 Phenomena Specific to CMOS Image Adjusting the Camera ...... 68 Sensors ..........50 Focusing on a Subject ....68 Shooting with Back Lighting ..
Operating or storing the camera in the maintenance. If abnormal noise occurs, following locations may cause damage to consult with your Sony dealer. the camera: • Extremely hot or cold places (Operating temperature: 0°C to 40°C [32°F to 104°F]) Note on laser beams •...
Phenomena Specific to CMOS Image Sensors The following phenomena that may appear in images are specific to CMOS (Complementary Metal Oxide Semiconductor) image sensors. They do not indicate malfunctions. White flecks Although the CMOS image sensors are produced with high-precision technologies, fine white flecks may be generated on the screen in rare cases, caused by cosmic rays, etc.
Overview Features Supplied Accessories CMOS camera with high image quality When you unpack, check that all the The CMOS video camera provides supplied accessories are included. 2,000,000 effective picture elements (pixels) that can shoot high-definition images to Camera (1) offer superior picture quality. Silent, high-speed pan and tilt action By adopting the DD motor mechanism, in addition to high-speed pan/tilt action,...
European model Location and Functions of Parts and Controls Camera Front Remote commander (1) Operating Instructions (1) A Lens This is a 10-magnification optical zoom lens. B Remote sensors These are sensors for the supplied Remote Commander. C POWER lamp Lights when the camera is connected to an AC outlet using the supplied AC power adaptor and AC power cord.
Page 53
K HD OUT COMPONENT connector Rear Supplies the images as an analog component (YPbPr) signal. L HD OUT HD-SDI connector Supplies the images as an HD-SDI signal which conforms to the SMPTE292M serial digital interface standard. M IR SELECT switch Select the camera number when you operate multiple cameras with the same Remote Commander.
Page 54
SDI, SD OUT VIDEO and SD OUT S Switch Video VIDEO connectors. position format 1080i/50 – Notes 1080p/25 – • Be sure to set this switch before you turn on the power of the camera. You can also 720p/50 – set this switch in the standby mode of the 720p/25 –...
B Switch 2 (Communication baud rate selector) Note Set to ON for 38400 bps, or OFF for If two or more cameras are adjacent and 9600 bps. have the same camera number, they are operated simultaneously with the same Remote Commander. When you install Note the cameras close to each other, set Set the communication baud rate before...
F POWER switch Press this button to turn on/off the Caution camera when the camera is connected to To avoid risk of explosion, use R6 (size AA) an AC outlet. manganese or alkaline batteries. G BACK LIGHT button Press this button to enable the backlight compensation.
Adjusting and Setting with Menus About On-Screen Setting Menus Menus The setting menu selected on the main menu is displayed. You can change various settings, such as shooting conditions and system setup of the camera, while observing menus displayed on a connected monitor. This section explains how to read the on- screen menus before starting menu operations.
Main menu Operating the Camera Using Menus For details on each menu, see page 60 to page 64. a Indicates that you should use the V or v button on the remote commander to select the setting menu. b Indicates that you can move to the next layer (setting menu) by pressing the HOME button.
Page 59
For detailed information on how to connect and VISCA command list, refer to the Technical Manual of the camera. For detailed information on how to get the Technical Manual, consult with your Sony dealer. To return to the main menu Press the DATA SCREEN button.
For the 50/25/ PAL video format: EXPOSURE Menu 1/2, 1/3, 1/6, 1/12, 1/25, 1/50, 1/75, 1/ 100, 1/120, 1/150, 1/215, 1/300, 1/425, 1/600, 1/1000, 1/1250, 1/1750, 1/2500, The EXPOSURE menu is used to set the 1/3500, 1/6000, 1/10000 sec. items related to the exposure. IRIS: Select the iris from among the following: CLOSE, F26, F22, F19, F16, F14, F11,...
Before starting the one-push white balance WHITE BALANCE adjustment, change the shutter speed to one which is faster than 1/60 (for 59.94/29.97/ Menu NTSC video format) or 1/50 (for 50/25/PAL video format). The WHITE BALANCE menu is used to select the white balance mode. MODE (white balance mode) Select the white balance mode from among the following:...
PICTURE Menu PAN TILT ZOOM Menu The PAN TILT ZOOM menu is used to select the pan/tilt/zoom mode. APERTURE (aperture compensation) Select the aperture compensation level from among MIN, 01 to 14 and MAX. PAN/TILT LIMIT When you set PAN/TILT LIMIT to ON, you PICTURE EFFECT can select the limit of pan/tilt operation.
You can select the magnification of the detailed information on how to get the electronic zoom from among ×4, ×2, or Technical Manual, consult with your Sony ×1.5. When you select x1, digital zoom does dealer. not operate. Only the optical zoom operates.
Message When STATUS Menu RESET n : OK You have reset the camera settings stored in POSITION 1 to 6 to The STATUS menu is used to display the the default settings. settings selected with the menus. One push WB : OP During the white balance adjustment in the ONE PUSH white balance mode, the...
For detailed information on how to check, refer to the Technical Manual.For detailed information on how to get the Technical Manual, consult with your Sony dealer. POWER lights. Connect the camera to an AC outlet using the supplied AC power adaptor and power cord.
turns off and the STANDBY lamp lights on Pan/Tilt and Zoom the camera. Operation Panning and Tilting POWER STANDBY lights. Press the POWER switch. The camera will turn on and perform the pan/tilt reset operation automatically. Press the arrow button to pan or tilt the camera.
If the camera moves in a different If the STANDBY lamp of the camera direction from the one you intended flashes The camera is preset so that the image output from the camera is rotated toward the right whenever you press the b button. To face the camera toward the opposite direction: You might wish to face the camera toward...
Operating Multiple Cameras Adjusting the with the Remote Commander Camera Set the IR SELECT switch on the rear of the camera you want to operate to 1, 2 or 3. Press the CAMERA SELECT button on the Remote Commander that corresponds to the number set in step Focusing on a Subject CAMERA...
To cancel the function, press the BACK Storing the Camera LIGHT button again. Settings in Memory — the Presetting Feature Subject Up to six combinations of settings (six appears positions) including camera position, brighter. zooming, focusing, and backlighting, can be preset.
Page 70
buttons, 1 to 6, in which you want to turned off and turned on again, store those positions in POSITION 1. store the settings. • Storing or cancelling the settings in POSITION 1 takes about 2 seconds longer than those of other positions. •...
Installation and Connection Installing the Attaching the Camera to a Tripod Camera Attach a tripod to the screw hole used for attaching a tripod on the bottom of the camera. Installing the Camera on a The tripod must be set up on a flat surface Desk and its screws tightened firmly by hand.
Remote Commander. To obtain a cable, consult with your Sony dealer. For detailed information on how to connect the camera and the VISCA command list, refer to the Technical Manual of the camera.
Connecting a Video Monitor, Connecting a Video Monitor, etc., Equipped with an Analog VTR, etc., Equipped with a Component (YPbPr) Input Composite Video Input Connector Connector or an S Video Connector HD OUT to AC outlet COMPONENT SD OUT SD OUT to AC outlet VIDEO S VIDEO...
Connecting a VTR Equipped with HD-SDI Input Connectors HD OUT to AC outlet HD-SDI Connecting cable with BNC connectors (not supplied) to HD-SDI input HDCAM, VTR, etc. equipped with an HD-SDI input connectors Note Set the SYSTEM SELECT switch to the position where the corresponding HD signal is output.
Appendix Troubleshooting Before bringing in your camera for service, cannot be corrected, consult with your Sony check the following as a guide to dealer. troubleshooting the problem. If the problem Symptom Cause Remedy The power of the camera is The AC power adaptor is not Insert the power cord firmly as not turned on.
Menu Configuration The menus of the camera are configured as The initial settings of each item are in bold. described below. (See page 60.) Menu Configuration...
Page 77
(See page 61.) (See page 62.) (See page 62.) Initial setting: +100° Initial setting: -100° Initial setting: +25° Initial setting: -25° (See page 63.) * This item appears only when an HD video format is selected with the SYSTEM SELECT switch. Menu Configuration...
Preset Items The following items set by using the Remote Commander and menu items can be stored in the memory of the camera. Items adjusted with the Remote Commander Preset item Preset position number Pan/Tilt Position Zoom Position Focus Mode Auto/Manual Focus Position Backlight Compensation ON/OFF Menu items...
Page 80
• IR Receive • IR Receive Return For detailed information on the VISCA command list, refer to the Technical Manual of the camera. For detailed information on how to get the Technical Manual, consult with your Sony dealer. Preset Items...
Control input/output Specifications VISCA IN: Mini DIN 8-pin type, RS-232C VISCA OUT: Mini DIN 8-pin type, RS-232C System Power connector Video signal 1080i/59.94, 1080i/50, 1080p/ JEITA type4 (DC IN 12V) 29.97, 1080p/25, 720p/59.94, 720p/50, 720p/29.97, 720p/25, General NTSC (LB), NTSC (CR), NTSC (SQ), PAL (LB), PAL Input voltage 12 V DC (10.8 to 13.0 V DC) (CR), PAL (SQ) (switched with...
Page 82
Dimensions Back Front Side Bottom Within a depth from 5 to 7 mm (7/32 to 9/32 inches) from the bottom surface. Within a depth from 5 mm (7/32 inches) or less from the bottom surface. Within a depth from 3 to 5 mm (1/8 to 7/32 inches) from the bottom surface.
Page 83
HD OUT COMPONENT connector (D- Pin assignments sub, 15-pin) VISCA IN connector (mini-DIN 8-pin, female) Function At YPbPr At YPbPr Pin No. Function COMPONEN COMPONEN T setting (at T setting (at DTR IN SYNC) DSR IN Pr-OUT Pr-OUT TXD IN Y-OUT Y-OUT Pb-OUT...