hit counter script
Fujitsu ScanPartner 600C User Manual
  1. Manuals
  2. Brands
  3. Fujitsu Manuals
  4. Scanner
  5. SCANPARTNER 600C
  6. User manual
Fujitsu ScanPartner 600C User Manual

Fujitsu ScanPartner 600C User Manual

Image scanner
Hide thumbs Also See for ScanPartner 600C:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
ScanPartner 600C
Image Scanner
User's Manual
Version 1.0
(Doc. No. 250-0062-0)

Advertisement

Table of Contents
loading

Related Manuals for Fujitsu ScanPartner 600C

Summary of Contents for Fujitsu ScanPartner 600C

  • Page 1 ScanPartner 600C Image Scanner User’s Manual Version 1.0 (Doc. No. 250-0062-0)

  • Page 2: Table Of Contents

    ADF Scanning …………………………………………………. Connecting the Cable …………………………………………. 13-14 15-17 MAINTENANCE ………….………………………. Cleaning the ADF ……………………….…………………….. 15-16 Cleaning the Glass ……………………………………………. 18-21 TROUBLESHOOTING ……………….………….. Question and Answer ………………………………………… 18-20 Paper Jam in the ADF ………………………………………… 20-21 SPECIFICATIONS ………….…………………….. Model: ScanPartner 600C ………………………………….….

  • Page 3: Introduction

    INTRODUCTION Congratulations on your purchase of a Fujitsu ScanPartner 600C Image Scanner. Before you install and operate the new Scanner, please take a few minutes to read through this manual. It provides you with the proper instructions on how to unpack, install, operate and maintain the Scanner.
  • Page 4 Power Cable User Manual Output Paper Tray Image Scanner Foam Foam Carton Figure 1-1 - Scanner Packing...

  • Page 5: Installation And Connections

    Installation and Connections Please unpack the Scanner carefully and check the contents against the “checklist”. If any items are missing or damaged, please contact your authorised local dealer immediately. Precautions: Keep the Scanner out of direct sunlight. Direct exposure to the sun or excessive heat may cause damage to the unit.
  • Page 6 Shipping Position Figure 2-1 - Removing the Shipping Bracket Use Position Figure 2-2 - Securing the Shipping Bracket...

  • Page 7: Refitting The Shipping Bracket

    2.1.2 Refitting the Shipping Bracket Whenever you need to move the Scanner to a new location it is advisable to refit the shipping bracket to avoid causing damage to the Scanners’ internal mechanism. Please follow the instructions below to refit the shipping bracket. Turn off the Scanner power at the power on/off switch.
  • Page 8 SCSI ID Selector Figure 2-3 - Adjusting the SCSI ID Setting...

  • Page 9: Adf Paper Chute

    ADF Paper Chute (Figure 2-4) Raise the right side of the paper chute to about 45 degrees. • Pull down the wire leg from under the paper chute ‚ iii) Insert the wire leg into the grips on the document cover Pull out the paper chute extension to the length you want.

  • Page 10: Adf Output Tray

    ADF Output Tray (Figure 2-5) Hold the output tray at an angle as shown in figure 2-5. • Insert the three protrusions on the paper output tray to the three slots on the ADF ‚ iii) Lower the paper tray gently .

  • Page 11: Document Loading

    Document Loading For flatbed scanning. Documents that cannot be scanned using the ADF can be placed on the flatbed for scanning. Refer to Figure 2-6). Place the document to be scanned onto the document glass face down. Position the document so that the corner is aligned with the reference mark. Document Cover Document Holding Pad Reference Mark...

  • Page 12: Adf Scanning

    ADF Scanning Standard paper sizes can be scanned automatically using the ADF. Refer to figure 2-7. To prevent occasional paper jams when automatically feeding documents, fan the documents before loading. Lift the balance wire and place the documents to be scanned onto the ADF paper chute face down, with the leading edge in the auto feeder entrance.

  • Page 13: Connecting The Cable

    Connect the power cable and SCSI signal cables as shown in Figure 2-8. SCSI Termination The Fujitsu ScanPartner 600C comes complete with a built in SCSI terminator. If the Scanner is the last device in a SCSI chain the terminator should be switched on. If the Scanner is not the last device the terminator should be switched off.
  • Page 14 SCSI Cable HOST COMPUTER Power Cable Power Switch PC SCSI Card Figure 2-8 - ScanPartner 600C Scanner Cable Connections SCSI Cable HOST COMPUTER Power Cable Power Switch Figure 2-9 ScanPartner 600C SCSI Scanner Cable Connections with Mac...

  • Page 15: Maintenance

    If this occurs please follow the cleaning procedures to return your Scanner to its original state. The cleaning procedures (Figure 3-1): Moisten a cotton swab with isoprophyl alcohol (95%). (Cleaner kits are available from Fujitsu). • Open the ADF unit by depressing the button in front of the ADF unit, carefully open the ADF to ‚...
  • Page 16 Feeding Roller Pad Assembly Figure 3-1 - Opening the ADF Unit and Document Cover...

  • Page 17: Cleaning The Glass

    Cleaning the Glass The procedures: Soak a cotton swab with some isoprophy alcohol (95%). Open the ADF unit and document cover as shown in Figure 3-2. Wipe the glass of flatbed area and ADF area by moving the swab from side to side. iii) Close the ADF unit and document cover.

  • Page 18: Troubleshooting

    If there is still no response, please reset the Scanner by turning it off and then on again, and reboot your host computer as well. Check if the driver is correctly installed. You can use the DIAG.EXE file in “Fujitsu Driver Kit” to check this out. Try to select another port memory. Question: Paper becomes jammed during scanning.

  • Page 19: Paper Jam In The Adf

    Question: When I power on the Scanner, the lamp does not light. Answer: The possibilities are as follows: The lamp is out of order. In that case, contact your authorised local dealer to change the lamp. The life time of the lamp is about 15,000 hours. The fuse on main board of the Scanner has blown.
  • Page 20 Figure 4.1 - ADF Paper Jam - Opening the ADF...
  • Page 21 Document (blank side) Figure 4-2 - ADF Paper Jam - Removing the Paper...

  • Page 22: Specifications

    Specifications All specifications are subject to change without notice. The following cannot be properly fed by ADF: Paper with clip or staple attached Paper with ink not totally dry Paper with inconsistent thickness, such as envelopes paper with large wrinkles, curls, folds or tears Tracing paper Coating paper Carbon paper...

  • Page 23: Model: Scanpartner 600C

    ScanPartner 600C Specifications Scanner Type 1-pass colour Flatbed with ADF built-in Scanning Mode 24-bit colour 8-bit Grey Scale (256 levels) Line Art Halftone (64 levels) Error Diffusion (single bit) Optical Resolution 600 x 1200 dpi in 1 dpi increments Light Source...

Table of Contents