INSTALLING THE FRIDGE / FREEZER ... 6 PREPARING THE FRIDGE / FREEZER ... 7 USING THE CONTROL FEATURES ... 7 STORING FOOD IN THE REFRIGERATOR OR FREEZER .. 11 MAKING ICE ... 13 USING THE WATER DISPENSER (OPTIONAL) ... 14 CoolSelect Zone DRAWER GUIDE (OPTIONAL) ...
This refrigerator must be properly installed and located in accordance with the Installation Instructions before it is used. Do not install the refrigerator in a damp place or a place where it may come in contact with water. Deteriorated insulation of electrical parts may •...
• The refrigerant used in the refrigerator/freezer and the gases in the insulation material require special disposal procedures. Ensure that none of the pipes on the back of the appliance are damaged prior to disposal.
Page 5
• may break and cause personal injury. Bottle should be stored tightly together in • the refrigerator so that they do not fall out. Do not spray inflammable gas near the refrigerator. There is a risk of explosion or fire.
INSTALLING THE FRIDGE/FREEZER Allow an adequate space and install the fridge/freezer on a firm, level floor. • If the appliance is not level, there may be unusual noises and poor cooling. • Wait for at least one hour before plugging the appliance in. Clean the fridge/freezer.
For the first five minutes after initial start-up, it may be slightly noisy. This is quite normal and does not represent a fault. Store food once the temperature in the refrigerator is sufficiently low. It takes a few hours after starting the refrigerator to reach the proper temperature.
Page 8
The current setting temperature is displayed ( – Press the REF.TEMP button one or more times until the required temperature is displayed ( – When you complete the setting of refrigerator temperature, the refrigerator temperature display ) flashes times.
Page 9
USING THE CONTROL FEATURES Vacation Button • If you are going on a long vacation or business trip or you do not need to use the refrigerator, press the Vacation button. • The refrigerator is switched off but the freezer remains on.
Page 10
• Select the details of the zone with the menu button. Freezer • Temperature setting range for freezer ➝ -14°C ~ -2°C Fridge • Temperature setting range for refrigerator ➝ 7°C ~ 1°C CoolSelect Zone : Temperature setting range Soft freeze (-°C) 0 zone (0°C) Cool (3°C)
Chiller Compartment • Ideal for storing fish, meat and sausage. • Temperature in this compartment are lower than in the refrigerator compartment. Temperatures below 0 °C may also occur. • A declared storage volume of fresh food compartment is calculated with Chiller Compartment removed.
Page 12
STORING FOOD IN THE REFRIGERATOR OR FREEZER Top freezer drawer • Store packed frozen foods, like ice cream, bacon and pizza. • Place the ice tray in this drawer in order to achieve optimal ice freezing. Middle/lower freezer drawer • Store fresh meat and fish or dried foods, which are divided into suitably sized portions.
To take out the ice cubes: • Twist the ice cube maker slightly. Danger of explosion • The coldest parts of the refrigerator is the rear panel. This is the best place to store delicate Warning foodstuffs. • Glass bottles containing liquids that can freeze should never be stored in the freezer as the glass can explode when the contents freeze.
USING THE WATER DISPENSER (OPTIONAL) With the water dispenser, you can obtain chilled water easily without opening the refrigerator door. In addition, you can save electricity by more than 30% reducing the number of times the door is open. Overview WHEN THE WATER DISPENSER IS NOT USED, THE FOLLOWINGS ARE RECOMMENDED Fix the water supply device tightly into the fixing hole.
Page 15
USING THE WATER DISPENSER (OPTIONAL) INSTALLING A REGULAR BOTTLE Press the fixing lever, lift the exclusive water tank upwards, then remove it. Remove the water supply device from the exclusive water tank, then set the inner groove of the water supply device in a regular mineral water bottle and fix-it in position by turning it.
CoolSelect Zone Drawer GUIDE (OPTIONAL) Cool, Zero Zone, Soft Freeze function • When you select Cool, Zero Zone or Soft Freeze function, 3°C, 0°C and -°C is selected. • Set by the Select button with the Menu button. Quick Cool •...
Rubber door seals • If the rubber door seals are dirty, the door will not close properly and the refrigerator and freezer will be unable to function efficiently. Clean them with a mild detergent and a damp cloth. Then wipe them with a dry cloth.
CLEANING THE WATER DISPENSER Dispenser Tray Pull out the tray with fingers. Empty the water in the dispenser tray, then clean it using warm water and detergent. Connection path Wipe out the connection path and surrounding area with a clean damp cloth.
REPLACING THE INTERIOR LIGHT (OPTIONAL) Always unplug the appliance when replacing the refrigerator light. Otherwise, there is the danger of electric shock. Push the both ends of the cover and pull it toward you. Incandescent light • Turn the interior light to pull it out and replace it with a new one.
Page 20
HOW TO INSTALL DOOR HANDLES REVERSING THE DOOR SWING 3. Attach an "ASSY HANDLE" on the door with special screws inside. 4. Attach Cover screws with "CAP HANDLE SCREW"s. When attaching the other "ASSY HANDLE", follow the same order as mentioned. When you disassemble them, just follow the reverse order.
REVERSING THE DOOR SWING - Read these instructions completely and carefully • Before reversing the door, ensure first that the refrigerator is disconnect by the plug from the mains. You should take out contents and accessories like door guard from the doors. Be Warning careful not to drop the doors during dissembling or assembling.
Page 22
2. Disconnect electric wires inside of the CAP CABI. 3. With a 7/16 inch wrench, remove bolts on the top of the refrigerator. 4. Disassemble the Fridge door by lifting it upward. Be careful not to drop and scratch the face of the Fridge door.
Page 23
REVERSING THE DOOR SWING 7. Switch the direction of the electric wire as below. Take out the COVER WIRE HINGE, L from the inside of the CAB CABI, and rejoin it with the electric wire. Make sure the length of the electric wire is more than 10mm.
Page 24
13. Remove the COVER LEG FRONT COVER by removing the screws. COVER LEG FRONT COVER 14. After tilting backward the refrigerator slightly for the convenience of the operation, disassemble the ASSY HINGE LOW as shown and put the AUTO GUIDE upside down, switch the position of the SHAFT.
Page 25
REVERSING THE DOOR SWING 19. Switch the position of the CAP HOLE HINGE UPP. CAPHOLE HINGE UPP 20. Reconnect the electric wires and reposition the wires inside of the CAP CABI as shown below. 21. Reassemble the CAP CABI, after assuring the position of Wires.
Page 26
REVERSING THE DOOR SWING 2. Unfasten the FOOT FRONT to fit the ASSY HINGE LOW. 26. Assemble the ASSY HINGE LOW as shown below with a wrench. 27. After switching the position of the CAP HOLE HINGE LOW, reassemble the COVER LEG FRONT with the door open.
• Is the temperature control on the front panel set to the coldest temperature? • Is the surrounding temperature too low? • Did you put the hot food in the refrigerator? There are unusual noises • Check that the appliance is installed on a stable, level floor.
• Put frozen food in the refrigerator to thaw. You can then use the low temperatures of the frozen products to cool food in the refrigerator. • Do not keep the door of the appliance open for too long when putting food in or taking food out.
VIEW OF YOUR FRIDGE / FREEZER REFRIGERATOR LIGHT (LED Lamp or incandescent, depending on the model) FRIDGE REFRIGERATOR SHELVES (tempered glass, depending on the model) FRESH SAFE DRAWER (OPTIONAL) FRESH SAFE DRAWER / CHILLED ROOM / COOLSELECT ZONE (OPTIONAL) FREEZER...
Page 30
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal. If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.