Page 1 FD 100/320Gbps NT and FX NT IHub Services Guide 7302 Intelligent Services Access Manager 7330 Intelligent Services Access Manager FTTN 7360 Intelligent Services Access Manager FX Release 5.6.01 FD 100/320Gbps NT and FX NT IHub Services Guide 3HH-11985-AAAA-TQZZA Issue: 13 June 2017 Nokia —...
Page 2 © 2014-2017 Nokia. Contains proprietary/trade secret information which is the property of Nokia and must not be made available to, or copied or used by anyone outside Nokia without its written authorization. Not to be used or disclosed except in accordance with applicable agreements.
Page 3: Table Of Contents
FD 100/320Gbps NT and FX NT IHub Services Guide Table of contents Preface...................41 Scope ......................41 Audience....................41 Required knowledge..................41 Product naming ..................41 Documents ....................41 Acronyms and initialisms ................41 Safety information..................42 Special information ..................42 Release notes....................42 Getting Started ................43 In This Document ..................43 Services Command Reference..............43 CLI Command Syntax Symbols..............44 Services Overview ................45...
Page 4 FD 100/320Gbps NT and FX NT IHub Services Guide 3.8.4.4 Deleting SDPs ...................58 3.8.4.5 Modifying LSPs..................58 3.8.4.6 Deleting LSPs....................59 Basic Configuration ...................59 3.10 Ethernet Connectivity Fault Management ..........60 3.10.1 Configuring ETH-CFM with CLI ..............63 3.10.1.1 Create a Maintenance Domain..............63 3.10.1.2 Create a Maintenance Association............63 3.11 G.8032 Ethernet Ring Protection Switching ..........64...
Page 5 FD 100/320Gbps NT and FX NT IHub Services Guide 3.17.4.1 eth-cfm.......................86 3.17.4.2 domain.......................87 3.17.4.3 association....................88 3.17.4.4 bridge-identifier..................88 3.17.4.5 mhf-creation....................89 3.17.4.6 ccm-interval ....................89 3.17.4.7 remote-mepid ....................90 3.17.4.8 inactivity-timer....................90 3.17.4.9 y1731pm....................91 3.17.4.10 shutdown ....................91 3.17.4.11 priority......................91 3.17.4.12 period......................92 3.17.4.13 data-size ....................92 3.17.4.14 measurement-period .................93 3.17.4.15 mac-address....................93...
Page 6 FD 100/320Gbps NT and FX NT IHub Services Guide 4.4.1 Common Configuration Tasks ..............112 4.4.2 Creating an Epipe Service...............112 4.4.2.1 Configure Epipe QoS Attributes ..............112 4.4.2.2 Configure Epipe Service MTU Attribute...........113 4.4.2.3 Configuring Epipe SAP Parameters ............113 4.4.2.4 Configuring SDP Bindings ...............115 4.4.3 Configuring Management Points (MEPs/MIPs) for Ethernet CFM on SDP bindings...................118...
Page 7 FD 100/320Gbps NT and FX NT IHub Services Guide 4.6.5.11 mep......................138 4.6.5.12 ccm-enable ....................139 4.6.5.13 ccm-ltm-priority ..................139 4.6.5.14 low-priority-defect ..................140 4.6.5.15 mac-address....................140 4.6.5.16 mip......................141 4.6.5.17 vlan-dot-1q-etype..................141 4.6.6 Show Commands ..................142 4.6.6.1 egress-label .....................142 4.6.6.2 ingress-label ....................143 4.6.6.3 sap-using ....................144 4.6.6.4 sdp......................145 4.6.6.5 sdp-using ....................146...
Page 8 FD 100/320Gbps NT and FX NT IHub Services Guide 5.4.6 VPLS IGMP Snooping (s,g) Flooding List ..........175 5.4.7 VPLS and Spanning Tree Protocol............175 5.4.7.1 Spanning Tree Operating Modes ............176 5.4.7.2 Multiple Spanning Tree................177 5.4.7.3 Redundancy Access to VPLS..............177 5.4.7.4 MSTP General Principles ................178 5.4.7.5 MSTP implementation ................178 5.4.7.6...
Page 9 FD 100/320Gbps NT and FX NT IHub Services Guide 5.8.6.3 Operationally Learning ................213 5.8.6.4 Operationally Forwarding ................213 5.8.7 Configuring SDP Bindings ...............214 Service Management Tasks ..............217 5.9.1 Modifying VPLS Service and SAP Parameters ........217 5.9.2 Enabling and Disabling VPLS Entities.............218 5.9.3 Deleting a VPLS Service or SAP.............219 5.9.4...
Page 10 FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.2.7 ignore-standby-signaling .................255 5.16.2.8 revert-time ....................255 5.16.2.9 static-mac ....................256 5.16.2.10 suppress-standby-signaling..............256 5.16.2.11 extfwd ......................257 5.16.2.12 device-ip ....................257 5.16.2.13 fdb-table-size ...................257 5.16.2.14 interface....................258 5.16.2.15 address....................259 5.16.2.16 arp-timeout ....................260 5.16.2.17 local-age ....................260 5.16.2.18 mesh-sdp....................261 5.16.2.19 spoke-sdp ....................262...
Page 11 FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.2.56 split-horizon-group...................283 5.16.2.57 vc-type .....................283 5.16.3 VPLS STP Commands ................284 5.16.3.1 stp......................284 5.16.3.2 auto-edge ....................284 5.16.3.3 edge-port ....................284 5.16.3.4 forward-delay...................285 5.16.3.5 hello-time ....................286 5.16.3.6 hold-count....................286 5.16.3.7 link-type ....................287 5.16.3.8 mst-instance ....................287 5.16.3.9 mst-path-cost...................287 5.16.3.10...
Page 12 FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.5.10 qos......................306 5.16.5.11 rate-limit....................307 5.16.5.12 rate-limit....................307 5.16.5.13 rate-limit-pbits ..................308 5.16.5.14 rate-limit....................308 5.16.5.15 dot1p......................309 5.16.5.16 meter-mode .....................310 5.16.6 VPLS Multicast commands..............310 5.16.6.1 igmp-snooping ..................310 5.16.6.2 fast-leave ....................310 5.16.6.3 last-member-query-interval..............311 5.16.6.4 mrouter-port.....................311 5.16.6.5 query-interval...................312 5.16.6.6 query-response-interval................313...
Page 13 FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.9.6 mesh-sdp....................344 5.16.9.7 spoke-sdp ....................344 5.16.9.8 stp......................345 5.16.9.9 detected-protocols ...................345 5.16.9.10 statistics....................346 5.16.9.11 mesh-sdp....................347 5.16.9.12 spoke-sdp ....................348 5.16.9.13 querier .....................348 5.16.10 Debug Commands...................349 5.16.10.1 id......................349 5.16.10.2 igmp-snooping ..................349 5.16.10.3 detail-level ....................349 5.16.10.4 mac......................350 5.16.10.5...
Page 14 FD 100/320Gbps NT and FX NT IHub Services Guide 6.9.1.1 Global Commands...................363 6.9.1.2 Interface Commands ................363 6.9.1.3 Interface SAP Commands ...............365 6.9.1.4 Show Commands ..................365 6.9.1.5 Clear Commands..................365 6.10 IES Service CLI Configuration Commands ..........366 6.10.1 Generic Commands.................366 6.10.1.1 shutdown ....................366 6.10.1.2 description ....................367 6.10.1.3...
Page 15 FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.7.6 option.......................388 6.10.7.7 interface-id....................389 6.10.7.8 remote-id ....................389 6.10.7.9 server.......................390 6.10.7.10 source-address..................390 6.10.7.11 icmp6 .......................390 6.10.7.12 packet-too-big..................391 6.10.7.13 param-problem ..................391 6.10.7.14 time-exceeded ..................392 6.10.7.15 unreachables ...................392 6.10.7.16 local-proxy-nd ..................393 6.10.7.17 prefix-stability...................394 6.10.7.18 prfx-hlddwn-time ..................394 6.10.8 IES SAP Filter and QoS Policy Commands ..........395...
Page 16 FD 100/320Gbps NT and FX NT IHub Services Guide 7.3.2 ISAM to PE Routing Protocols..............424 Configuring a VPRN Service with CLI .............424 Basic Configuration .................425 Common Configuration Tasks ..............426 Configuring VPRN Components..............427 7.7.1 Creating a VPRN Service ................427 7.7.2 Configuring Global VPRN Parameters ............427 7.7.3 Configuring Router Interfaces..............428 7.7.4...
Page 17 FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.2.13 mtu......................457 7.10.2.14 other-stateful-configuration..............457 7.10.2.15 prefix......................457 7.10.2.16 autonomous.....................458 7.10.2.17 on-link ......................458 7.10.2.18 preferred-lifetime ..................459 7.10.2.19 valid-lifetime.....................459 7.10.2.20 reachable-time..................460 7.10.2.21 retransmit-time..................460 7.10.2.22 router-lifetime...................460 7.10.2.23 route-distinguisher ...................461 7.10.2.24 router-id ....................461 7.10.2.25 sgt-qos.....................462 7.10.2.26 qos......................462 7.10.2.27 rate-limit....................463...
Page 18 FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.6.7 remote-id ....................485 7.10.6.8 prefix-stability...................485 7.10.6.9 prfx-hlddwn-time ..................486 7.10.6.10 server.......................486 7.10.6.11 source-address..................487 7.10.6.12 icmp6 .......................487 7.10.6.13 packet-too-big..................487 7.10.6.14 param-problem ..................488 7.10.6.15 time-exceeded ..................489 7.10.6.16 unreachables ...................489 7.10.6.17 local-proxy-nd ..................490 7.10.7 SAP Commands ..................490 7.10.7.1 sap......................490 7.10.8...
Page 19 FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.9.21 ibgp-multipath ..................509 7.10.9.22 import.......................509 7.10.9.23 keepalive ....................510 7.10.9.24 local-address ...................510 7.10.9.25 local-as ....................511 7.10.9.26 local-preference..................512 7.10.9.27 loop-detect....................513 7.10.9.28 med-out ....................514 7.10.9.29 min-as-origination ..................515 7.10.9.30 min-route-advertisement................515 7.10.9.31 multihop ....................516 7.10.9.32 multipath ....................516 7.10.9.33 next-hop-self....................517 7.10.9.34...
Page 20 FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.10.29 external-preference .................536 7.10.10.30 overload....................537 7.10.10.31 overload-include-stub ................538 7.10.10.32 overload-on-boot ..................538 7.10.10.33 preference ....................539 7.10.10.34 reference-bandwidth................540 7.10.10.35 timers.......................541 7.10.10.36 lsa-arrival ....................541 7.10.10.37 lsa-generate.....................542 7.10.10.38 spf-wait ....................542 7.10.11 RIP Commands ..................543 7.10.11.1 rip......................543 7.10.11.2 authentication-key ...................543...
Page 21 FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.12.22 neighbor....................578 7.10.12.23 paths......................582 7.10.12.24 routes.......................583 7.10.12.25 summary....................586 7.10.12.26 interface....................587 7.10.12.27 dhcp6.......................590 7.10.12.28 statistics....................590 7.10.12.29 summary....................591 7.10.12.30 routes.......................591 7.10.12.31 neighbour....................592 7.10.12.32 rip......................593 7.10.12.33 database....................593 7.10.12.34 neighbor....................594 7.10.12.35 peer ......................596 7.10.12.36 statistics....................597 7.10.12.37 route-table ....................599 7.10.12.38...
Page 22 FD 100/320Gbps NT and FX NT IHub Services Guide Mirror Service CLI Configuration Commands..........616 8.7.1 Generic Commands.................616 8.7.1.1 description ....................616 8.7.1.2 shutdown ....................617 8.7.2 Mirror Configuration Commands .............618 8.7.2.1 mirror-dest ....................618 8.7.2.2 sap......................619 8.7.3 Debug Configuration Commands ............621 8.7.3.1 mirror-source ...................621 8.7.3.2 port ......................621 8.7.3.3...
Page 23 FD 100/320Gbps NT and FX NT IHub Services Guide List of figures Services Overview ................45 Figure 1 Service Entities..................48 Figure 2 Service Access Point (SAP) ..............49 Figure 3 SDP ......................50 Figure 4 Service Creation and Implementation Flow..........52 Figure 5 Ring in the initial state ................65 Figure 6 Ring in the protection state................66 Figure 7...
Page 24 FD 100/320Gbps NT and FX NT IHub Services Guide 3HH-11985-AAAA-TQZZA Issue: 13...
Page 25 FD 100/320Gbps NT and FX NT IHub Services Guide List of tables Getting Started ................43 Table 1 Configuration Process ................43 Table 2 Command Syntax Symbols ...............44 Services Overview ................45 Table 3 Acronym callout ..................61 Table 4 description command ................79 Table 5 description command ................79 Table 6 customer command ...................80...
Page 26 FD 100/320Gbps NT and FX NT IHub Services Guide Table 44 Show Service Service-using Command Output Fields......99 Table 45 sdp command ..................100 Table 46 Show Service SDP Command Output Fields ..........101 Table 47 sdp-using command ................102 Table 48 Show Service SDP-using Command Output Fields ........102 Table 49 eth-ring command..................102 Table 50...
Page 27 FD 100/320Gbps NT and FX NT IHub Services Guide Table 92 sdp-using command ................146 Table 93 Show Service sdp-using Output Fields............147 Table 94 id command .....................147 Table 95 all command ....................148 Table 96 Show Service-ID All Output Fields ............148 Table 97 base command ..................151 Table 98 Show Service-ID Base Output Fields ............151...
Page 28 FD 100/320Gbps NT and FX NT IHub Services Guide Table 140 arp-timeout command................260 Table 141 local-age command .................260 Table 142 mesh-dsp command ................261 Table 143 spoke-sdp command ................262 Table 144 control-word command ................264 Table 145 hash-label command ................264 Table 146 egress command ..................265 Table 147 ingress command ..................265...
Page 29 FD 100/320Gbps NT and FX NT IHub Services Guide Table 189 link-type command ..................287 Table 190 mst-instance command ................287 Table 191 mst-path-cost command ................287 Table 192 mst-port-priority command...............288 Table 193 max-age command..................288 Table 194 mode command..................289 Table 195 mst-instance command ................289 Table 196 mst-priority command ................290 Table 197...
Page 30 FD 100/320Gbps NT and FX NT IHub Services Guide Table 238 mrouter-port command ................311 Table 239 query-interval command ................312 Table 240 query-response-interval command ............313 Table 241 query-src-ip command................313 Table 242 report-src-ip command ................314 Table 243 robust-count command................314 Table 244 send-queries command ................315 Table 245 static command ..................315 Table 246...
Page 31 FD 100/320Gbps NT and FX NT IHub Services Guide Table 287 id command .....................340 Table 288 statistics command ..................340 Table 289 fdb command...................341 Table 290 sap command ..................343 Table 291 counters command ..................343 Table 292 mesh-sdp command ................344 Table 293 spoke-sdp command ................344 Table 294 stp command ...................345...
Page 32 FD 100/320Gbps NT and FX NT IHub Services Guide Table 335 ip-mtu command..................376 Table 336 local-proxy-arp command ................377 Table 337 loopback command .................377 Table 338 protect command..................378 Table 339 secondary command ................378 Table 340 dhcp command ..................380 Table 341 gi-address command ................380 Table 342 lease-query command ................381 Table 343...
Page 33 FD 100/320Gbps NT and FX NT IHub Services Guide Table 384 base command ..................405 Table 385 dhcp command ..................405 Table 386 statistics command ..................405 Table 387 lease-state command ................406 Table 388 summary command .................408 Table 389 Show DHCP Summary Output ..............408 Table 390 dhcp6 command ..................408 Table 391...
Page 34 FD 100/320Gbps NT and FX NT IHub Services Guide Table 432 router-lifetime command................460 Table 433 route-distinguisher command ..............461 Table 434 router-id command ..................461 Table 435 sgt-qos command ..................462 Table 436 qos command ..................462 Table 437 rate-limit command ..................463 Table 438 rate-limit command ..................464 Table 439 static-route command ................465...
Page 35 FD 100/320Gbps NT and FX NT IHub Services Guide Table 481 local-proxy-nd command .................490 Table 482 sap command ..................490 Table 483 egress command ..................492 Table 484 egress command ..................492 Table 485 ingress command ..................492 Table 486 ingress command ..................493 Table 487 filter command ..................493 Table 488 filter command ..................494...
Page 36 FD 100/320Gbps NT and FX NT IHub Services Guide Table 530 next-hop-self command ................517 Table 531 passive command..................518 Table 532 peer-as command..................518 Table 533 preference command................519 Table 534 prefix-limit command ................519 Table 535 rapid-withdrawal command..............520 Table 536 remove-private command................520 Table 537 type command ..................521 Table 538 ospf command ..................521...
Page 37 FD 100/320Gbps NT and FX NT IHub Services Guide Table 579 authentication-key command..............543 Table 580 authentication-type command ..............544 Table 581 check-zero command ................545 Table 582 split-horizon command ................545 Table 583 export command..................546 Table 584 import command..................546 Table 585 message-size command................547 Table 586 metric-in command ..................547 Table 587...
Page 38 FD 100/320Gbps NT and FX NT IHub Services Guide Table 628 auth-keychain command .................574 Table 629 damping command ..................574 Table 630 Show BPG Damping Output..............575 Table 631 group command..................576 Table 632 Show Group Output.................577 Table 633 neighbor command..................578 Table 634 Show BPG Neighbor Output..............579 Table 635 Show Advertised and Received Route Output ........582...
Page 39 FD 100/320Gbps NT and FX NT IHub Services Guide Table 677 damping command ..................605 Table 678 flap-statistics command ................605 Table 679 neighbor command..................606 Table 680 protocol command ...................606 Table 681 database command .................607 Table 682 statistics command ..................607 Table 683 router-advertisement command...............607 Table 684 id command .....................608...
Page 40 FD 100/320Gbps NT and FX NT IHub Services Guide 3HH-11985-AAAA-TQZZA Issue: 13...
Page 41: Preface
Readers must be familiar with general telecommunications principles. 1.4 Product naming When the term “ISAM” is used alone, then the 7302 ISAM, the 7330 ISAM FTTN and the 7360 ISAM FX are meant. If a feature is valid for only one of the products, the applicability will be explicitly stated.
Page 42: 1.7 Safety Information
Preface FD 100/320Gbps NT and FX NT IHub Services Guide 1.7 Safety information For safety information, see the Safety Manual for your product. 1.8 Special information The following are examples of how special information is presented in this document. Danger indicates that the described activity or Danger —...
Page 43: Getting Started
FD 100/320Gbps NT and FX NT IHub Services Guide Getting Started 2 Getting Started 2.1 In This Document 2.2 Services Command Reference 2.3 CLI Command Syntax Symbols 2.1 In This Document This document provides process flow information to configure provision services. Table lists the tasks necessary to configure services.
Page 44: 2.3 Cli Command Syntax Symbols
Getting Started FD 100/320Gbps NT and FX NT IHub Services Guide • Service Configuration Commands • VLL Services CLI Command Reference • VPLS Service CLI Command Reference • IES Services CLI Command Reference • VPRN Services CLI Command Reference • Mirror Service CLI Command Reference 2.3 CLI Command Syntax Symbols This section explains the symbols used throughout this manual within a CLI...
Page 45: Services Overview
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3 Services Overview 3.1 In this Chapter 3.2 Introduction 3.3 ISAM Service Model 3.4 Service Entities 3.5 Service Creation Process Overview 3.6 Deploying and Provisioning Services 3.7 Configuration Notes 3.8 Configuring Global Service Entities with CLI 3.9 Basic Configuration 3.10 Ethernet Connectivity Fault Management...
Page 46: 3.2 Introduction
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide 3.2 Introduction A service is a globally unique entity that refers to a type of connectivity service for either Internet or VPN connectivity. Each service is uniquely identified by a service ID within a service area.
Page 47: Service Policies
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.2.2 Service Policies Common to all ISAM connectivity services are filter policies that are assigned to the service. Filter policies are defined at a global level and then applied to a service on the router.
Page 48: 3.4 Service Entities
Each subscriber service type is configured with at least one service access point (SAP). A SAP identifies the interface point for a service on an Nokia ISAM router (Figure 2). The SAP configuration requires that slot information be specified. The slot parameters must be configured prior to provisioning a service (see the “Port...
Page 49: Sap Configuration Considerations
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview Figure 2 Service Access Point (SAP) Customer Cust-27 3/1/6 dot1q IP Network Service Customer 2/2/3 dot1q ALA-A 3.4.2.1 SAP Configuration Considerations When configuring a SAP, consider the following: • An SAP is a local entity and only locally unique to a given device.
Page 50: Sdp Bindings
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide An SDP has the following characteristics: • An SDP is locally unique to a participating ISAM. The same SDP ID can appear on other service routers/ISAMs. • An SDP uses the system IP address to identify the far-end PE. •...
Page 51: Mpls
“ports” (spoke SDPs and SAPs) and not transmitted on any mesh SDPs. SDP Encapsulation Types The Nokia service model uses encapsulation tunnels through the core to interconnect with service edge routers. An SDP is a logical way of referencing the entrance to an encapsulation tunnel. The following encapsulation types are supported: Layer 2 with LDP signaled.
Page 52: 3.6 Deploying And Provisioning Services
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Figure 4 Service Creation and Implementation Flow START CORE PERFORM PREREQUISITE CONFIGURATIONS: SERVICES CUSTOMER ACCOUNTS, SDPs, QoS POLICIES, FILTER POLICIES,LSPs SUBSCRIBER ACCESS OPERATOR CONSOLE GUI SERVICES OR CLI VIA TELNET OR DIRECT ATTACHMENT CREATE SERVICE TYPE, SPECIFYING SERVICE ID AND CUSTOMER ID CONFIGURE SAP/INTERFACE DEFINE PORT-ID...
Page 53: Phase 1: Core Network Construction
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.6.1 Phase 1: Core Network Construction Before the services are provisioned, the following tasks should be completed: • Build the IP or IP/MPLs core network. • Configure routing protocols. •...
Page 54: 3.8 Configuring Global Service Entities With Cli
Configuring an SDP • Service Management Tasks 3.8.1 Service Model Entities The Nokia service model uses logical entities to construct a service. The service model contains four main entities to configure a service. • Service Distribution Points (SDPs) • Services: •...
Page 55: Configuring An Sdp
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview ------------------------------------------- customer 5 create description “Nokia Customer” contact “Technical Support” ------------------------------------------- A:A:ALA-12>configure>service# 3.8.3 Configuring an SDP The most basic SDP must have the following: • A locally unique SDP identification (ID) number.
Page 56: Configuring An Sdp
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide 3 Specify an encapsulation type. 4 Specify a far-end node. 3.8.3.2 Configuring an SDP When specifying MPLS SDP parameters, you can only specify a static LSP name, an RSVP-based LSP or enable LDP. There cannot be 2 methods of transport in a single SDP.
Page 57: Service Management Tasks
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.8.4 Service Management Tasks This section discusses the following service management tasks: • Modifying Customer Accounts • Deleting Customers • Modifying SDPs • Deleting SDPs • Modifying LSPs • Deleting LSPs 3.8.4.1 Modifying Customer Accounts...
Page 58: Deleting Sdps
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Example: configure>service# sdp 79 configure>service>sdp# description "Path-to-107" configure>service>sdp# shutdown configure>service>sdp# far-end "10.10.10.107" configure>service>sdp# path-mtu 1503 configure>service>sdp# no shutdown To match the incoming traffic’s TPID with SDP, you can use vlan-vc-etype. the following scenarios can occur: •...
Page 59: Deleting Lsps
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview configure>router>mpls# static-lsp to-headquarters configure>router>mpls>static-lsp# push 105 nexthop 138.3.5.27 configure>router>mpls>static-lsp# to 1.1.1.1 configure>router>mpls>static-lsp# no shutdown 3.8.4.6 Deleting LSPs The no form of the lsp command removes an LSP ID and all associated information. Before an LSP can be deleted, the LSP must be removed from all SDP associations.
Page 60: 3.10 Ethernet Connectivity Fault Management
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide description "MPLS-10.10.10.104" far-end 10.10.10.104 signaling tldp path-mtu 4462 no shutdown exit epipe 6000 customer 6 create service-mtu 1514 sap lt:1/1/2:0 create no shutdown exit spoke-sdp 2:6111 create no shutdown exit no shutdown exit...
Page 61: Table 3 Acronym Callout
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview Table 3 Acronym callout Acronym Description Continuity check message Connectivity fault management ETH-CFM Ethernet Connectivity Fault Management Loopback message Loopback reply Linktrace message Linktrace reply Maintenance entity Maintenance association MA-ID Maintenance association identifier Maintenance domain...
Page 62 Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide • For VPLS and v-VPLS services: • CFM can be enabled or disabled on a SAP or SDP bindings basis. • Up and/or down MEP with a MEP-ID on a SAP and SDP binding for each MD level can be configured, modified, or deleted.
Page 63: Configuring Eth-Cfm With Cli
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.10.1 Configuring ETH-CFM with CLI This section provides information to configure global ETH-CFM parameters using the Command Line Interface (CLI). Topics in this section include: • Create a Maintenance Domain •...
Page 64: 3.11 G.8032 Ethernet Ring Protection Switching
VID. G.8032 controls the active state for the data VLAN (ring data instances) associated with a control instance. Multiple control instances allow logically separate rings on the same topology. The Nokia implementation supports dot1q encapsulation for data ring instances and the control channel.
Page 65: Figure 5 Ring In The Initial State
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview R-APS messages are periodically sent around in both directions to tell other nodes in the Ring about the blocked port in the RPL owner node. In non-revertive mode any link may be the RPLY link.1731 Ethernet OAM CC is the basis of the RAPS messages used by nodes in the ring to monitor the health of each link in the ring in both directions.
Page 66: Figure 6 Ring In The Protection State
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Figure 6 Ring in the protection state Once the failed link recovers, the nodes that blocked the link again send the R-APS messages indicating no failure this time. This in turn triggers RPL Owner to block the RPL link and indicate the Blocked RPL link the ring in R-APS message, which when received by the nodes at the recovered link cause them to unblock that link and restore connectivity (again all nodes in the ring perform FBD Flush and MAC learning...
Page 67: Sample Configuration
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview Ethernet R-APS can be configured on any port configured for access or hybrid mode using dot1q encapsulation enabling support for Ethernet RAPS protected services on the service edge towards the customer site, or within the Ethernet backbone. The intention of this is to cause minimum disruption to the service during Ethernet RAPS failure detection and recovery.
Page 68: Oam Considerations
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide no shutdown exit exit no shutdown no shutdown exit Associating eth-ring instance to a sap: Configure service vpls 20 customer 1 v-vpls vlan 100 create description "Ring Control VID 100" sap nt-a:xfp:1:100 eth-ring 1 create //control sap for path-a exit...
Page 69: Duplex Nt Erps Performance Considerations
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.11.5 Duplex NT ERPS Performance considerations This section suggests actions to be performed by the operator to optimize performance impacts in the event of Active-NT switchover on a Duplex Load-Balanced NT.
Page 70 Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide 7 If ccm-errors need not be propagated to the ring path (operational status), configure all the defects as low-prio-defects for the eth-cfm mep of the corresponding path. 8 Configure a control SAP (on a v-VPLS service) for the ring path with VLAN as r-aps tag.
Page 71: 3.12 Dhcp Lease Query
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview *A:FAD-Chassis>configure>eth-ring>path# eth-cfm *A:FAD-Chassis>configure>eth-ring>path>eth-cfm# mep 11 domain 100 association 1 *A:FAD-Chassis>configure>eth-ring>path>eth-cfm>mep# control-mep *A:FAD-Chassis>configure>eth-ring>path>eth-cfm>mep# no shutdown *A:FAD-Chassis# configure service vpls 1002 customer 1 v-vpls vlan 1002 *A:FAD-Chassis>configure>service>vpls$ sap lag-30:1002 MINOR: SVCMGR #1602 The SAP-id is already in use - lag-30:1002 is already configured under Ethernet ring 10 *A:FAD-Chassis>configure>service>vpls$ sap lag-30:1002 eth-ring 10 *A:FAD-Chassis>configure>service>vpls>sap$...
Page 72: 3.13 Dhcp Remote Id Check
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide with 95 sessions for each type such as SLQ, BLQ IPv4, and BLQ IPv6, and with 5 queries x 19 LTs. IHUB supports lease query messages generated by the LT, and legacy behavior of forwarding LQ packets will be maintained.
Page 73: Public Tunnel Saps
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview • Public tunnel interface • This interface can be either an IES or VPRN interface • This interface represents the public side of the GRE tunnel • Private tunnel interface •...
Page 74: Gre Tunnel Configuration
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide In the above example, the IP address 10.0.0.1 is the address of the GRE tunnel endpoint from the perspective of the payload IP packets. This address belongs to the address space of the VPRN 1 service and is not exposed to the public IP network carrying GRE encapsulated packets.
Page 75: Statistics Collection
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview • oper state • type (GRE-only) 3.14.4 Statistics Collection GRE tunnel statistics are enabled or disabled dynamically using CLI commands. The statistics counter includes the number of Rx packets, Rx bytes, Tx packets, and Tx bytes.
Page 76: 3.16 Global Services Command Reference
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide • The same DHCPv6 PD is delegated to two different devices In this scenario, the PD is not delegated to the second Note — device, since it is considered to be an invalid delegation. Duplicate PD Alarm will be cleared in the following scenarios: •...
Page 77: Customer Management Commands
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.16.1.1 Customer Management Commands configure — service — customer customer-id [create] — [no] customer customer-id — contact contact-information — no contact contact-information — description description-string — no description — sdp-id mpls —...
Page 78: Show Commands
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide — [no] path {a|b} port-id raps-tag qtag/qinqtag — description description-string — eth-cfm — mep-id domain md-index association ma-index — ccm-enable — ccm-ltm-priority priority — control-mep — low-priority-defect{allDef|macRemErrXcon|remErrXcon|errXcon|xcon|noXcon} — mac-address xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx —...
Page 79: Description
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.17.1.1 description Table 4 description command Item Description Syntax description description-string no description Context configure>service>customer configure>eth-ring configure>eth-ring>path Description This command creates a text description stored in the configuration file for a configuration context.
Page 80: Customer
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide 3.17.2.1 customer Table 6 customer command Item Description Syntax customer customer-id [create] no customer customer-id Context configure>service Description This command creates a customer ID and customer context used to associate information with a particular customer.
Page 81: Sdp Commands
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.17.3 SDP Commands 3.17.3.1 Table 8 sdp command Item Description Syntax sdp sdp-id mpls no sdp sdp-id Context configure>service Description This command creates or edits a Service Distribution Point (SDP). SDPs must be explicitly configured.
Page 82: Far-End
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Table 9 adv-mtu-override command Item Description Syntax [no] adv-mtu-override Context configure>service>sdp sdp-id Description This command overrides the advertised VC-type MTU. When enabled, the ISAM signals a VC MTU equal to the service MTU (includes the Layer 2 header). Under normal operations it will advertise the service MTU minus the Layer 2 header.
Page 83: Ldp
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.17.3.4 Table 11 ldp command Item Description Syntax [no] ldp Context configure>service>sdp sdp-id Description This command enables LDP-signaled LSPs on MPLS-encapsulated SDPs. In MPLS SDP configurations either one LSP can be specified or LDP can be enabled. The SDP ldp and lsp commands are mutually exclusive.
Page 84: Path-Mtu
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command creates associations between one or more label switched paths (LSPs) and an Multi- Protocol Label Switching (MPLS) Service Distribution Point (SDP). This command is implemented only on MPLS-type encapsulated SDPs.
Page 85: Signaling
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.17.3.7 signaling Table 14 signaling command Item Description Syntax signaling {off | tldp} Context configure>service>sdp sdp-id Description This command specifies the signaling protocol used to obtain the ingress and egress labels in frames transmitted and received on the SDP.
Page 86: Vlan-Vc-Etype
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Special Cases Service Admin State - Bindings to an SDP within the service will be put into the out-of-service state when the service is shutdown. While the service is shutdown, all customer packets are dropped and counted as discards for billing and debugging purposes.
Page 87: Domain
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview Table 17 eth-cfm command Item Description Syntax eth-cfm Context configure Description This command enables the context to configure 802.1ag CFM parameters 3.17.4.2 domain Table 18 domain command Item Description Syntax domain md-index [format {dns | mac | none | string}] name md-name level level domain md-index...
Page 88: Association
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide 3.17.4.3 association Table 19 association command Item Description Syntax association ma-index [format {icc-based | integer |string | vid | vpn-id}] name ma-name association ma-index no association ma-index Context configure>eth-cfm>domain Description This command configures the Maintenance Association (MA) for the domain The no form of the command removes the MA index parameters from the configuration.
Page 89: Mhf-Creation
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview Item Description Parameters bridge-id - Specifies the bridge ID for the domain association. Values: 1...2147483647 (2 of 2) 3.17.4.5 mhf-creation Table 21 mhf-creation command Item Description Syntax mhf-creation {default | none | explicit} no mhf-creation Context configure>eth-cfm>domain>association>bridge-identifier...
Page 90: Remote-Mepid
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters interval — Specifies the interval between CCM transmissions to be used by all MEPs in the Values: 100 milliseconds, 1 second, 10 seconds, 60 seconds, and 600 seconds (2 of 2) 3.17.4.7 remote-mepid...
Page 91: Y1731Pm
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.17.4.9 y1731pm Table 25 y1731pm command Item Description Syntax domain md-index association ma-index mep mep-id session session-id [create] Context configure>eth-cfm>y1731pm Description This command creates a y1731pm session for the given mep. The no form of the command will remove the y1731pm session.
Page 92: Period
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Default Parameters priority — <0,1,2…7> (2 of 2) 3.17.4.12 period Table 28 period command Item Description Syntax period period Context configure>eth-cfm>y1731pm>domain Description The value of period specifies the time to wait between the transmission of one OAM request and the next.
Page 93: Measurement-Period
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.17.4.14 measurement-period Table 30 measurement-period command Item Description Syntax measurement-period period Context configure>eth-cfm>y1731pm>domain Description The value of measurement-period specifies the time after which the synthetic loss calculation is made periodically. If the value of this object is set to 'X' seconds, loss measurement calculations are done after every 'X' seconds.
Page 94: Ethernet Ring Global Commands
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>eth-cfm>y1731pm>domain Description The value of type indicates the type of y1731pm session this row details. The no form of the command reverts the value to the default. Default None.
Page 95: Ccm-Hold-Time
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview Item Description Description Configures the Wait-To-Restore (WTR) Timer. RPL owner uses the WTR delay timer before initiating an RPL block in case of revertive mode of operation. WTR timer is used to prevent frequent redundancy transactions as result of an intermittent signal failure defects.
Page 96: Node-Id
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Table 36 guard-time command Item Description Syntax guard-time time Context configure>eth-ring Description Configure the eth-ring guard time Parameters time - eth-ring guard time in deciseconds Values: 1...20 Default: 5 3.17.5.5 node-id Table 37...
Page 97: Path
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.17.5.7 path Table 39 path command Item Description Syntax path {a|b} port-id raps-tag qtag|qinqtag Context configure>eth-ring Description This command configures one of the two paths supported under the Ethernet ring. The no form of this command removes the path from under the Ethernet ring.
Page 98: Customer
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide 3.17.6.1 customer Table 41 customer command Item Description Syntax customer [customer-id] [site customer-site-name] Context show>service Description Displays service customer information. Parameters customer-id — Displays only information for the specified customer ID. Default: All customer IDs display.
Page 99: Table 44 Show Service Service-Using Command Output Fields
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview Item Description Context show>service Description This command displays the services matching certain usage properties. If no optional parameters are specified, all services defined on the system are displayed. Parameters epipe —...
Page 100: Sdp
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide ============================================================================ *A:ALA-12# *A:ALA-12# show service service-using epipe ============================================================================ Services [epipe] ============================================================================ ServiceId Type CustomerId Last Mgmt Change ---------------------------------------------------------------------------- Epipe 06/22/2006 23:05:58 Epipe 06/22/2006 23:05:58 Epipe 06/22/2006 23:05:58 Epipe 06/22/2006 23:05:58 ---------------------------------------------------------------------------- Matching Services : 4 ============================================================================...
Page 101: Sdp-Using
FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview Item Description Parameters sdp-id — The SDP ID for which to display information. Default:All SDPs. Values: 1 — 17407 far-end ip-address — Displays only SDPs matching with the specified far-end IP address. Default: SDPs with any far-end IP address.
Page 102: Eth-Ring
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Table 47 sdp-using command Item Description Syntax sdp-using [sdp-id[:vc-id] | far-end ip-address] Context show>service Description Display services using SDP or far-end address options. Parameters sdp-id — Displays only services bound to the specified SDP ID. Values: 1 —...
Page 103 FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview Item Description Description Display Ethernet ring status information (or) path information Parameters ring-index — Ethernet ring index. Values: 1 — 64 (2 of 2) Sample output: # show eth-ring ============================================================================ Ethernet Rings (summary) ============================================================================...
Page 104: Tools Command
Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide LowestDefectPri : macRemErrXcon HighestDefect : none Defect Flags : None Mac Address : 00:07:72:ac:0d:a5 ControlMep : True CcmLtmPriority CcmTx CcmSequenceErr Fault Propagation : disabled LbRxReply LbRxBadOrder LbRxBadMsdu LbTxReply LbNextSequence LtNextSequence LtRxUnexplained ========================================================...
Page 105 FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview state:TxInfo (Bytes) Time === ===== ================================================ ==== aAdd PROT: 0xb040 Sf(DNF ) Tx--> Blk --- 497 02:18:11.480 bAdd PROT: 0xb020 Tx--> Blk Blk 497 02:18:11.480 pdu B: 00:07:72:a8:54:a8-0x0000 Nr PROT: 0xb020 Rx<-- Blk Blk 497 02:18:26.080 PROT: 0xb040...
Page 106 Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide 3HH-11985-AAAA-TQZZA Issue: 13...
Page 107: Virtual Leased Line Services
4.2 Ethernet Pipe (Epipe) Services 4.2.1 Epipe Service Overview An Epipe service is Nokia’s implementations of an Ethernet VLL based on the IETF “Martini Drafts” (draft-martini-l2circuit-trans-mpls-08.txt and draft-martini-l2circuit-encapmpls-04.txt) and the IETF Ethernet Pseudo-wire Draft (draft-so-pwe3-ethernet-00.txt). An Epipe service is a layer 2 point-to-point service where the customer data is encapsulated and transported across a service provider’s IP or MPLS network.
Page 108: Traffic Management Support
Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Figure 9 Epipe/VLL Service Customer 1 Customer 2 IP/MPLS Network EPIPE (VLL) Service 1 Customer 1 EPIPE (VLL) Service 2 Customer 2 4.2.2 Traffic Management Support An aggregate egress rate limiter can be associated to an Epipe service. The rate limiter applies to traffic associated to the service which egresses on regular ports (network ports).
Page 109: Vll Service Considerations
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services Figure 10 Pseudo wire ISAM LSP1.1 VLL/ VPLS VLL/ VPLS LSP1.2 As shown in Figure 10, a Pseudo-Wire has been established between the ISAM and PE1. The MPLS tunnel passes through Router R1 as this is the shortest path between the ISAM and PE1.
Page 110: Sap Encapsulations And Pseudowire Types
Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Figure 11 SDP Statistics for VPLS and VLL Services SDP 103 VPLS1 VPLS1 VPLS2 VPLS2 IP/MPLS SDP 101 SDP 102 VPLS2 VPLS1 4.3.2 SAP Encapsulations and Pseudowire Types The Epipe service is designed to carry Ethernet frame payloads, so it can provide connectivity between any two SAPs that pass Ethernet frames.
Page 111: Ingress Network Classification
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services 4.3.3.2 Ingress Network Classification A service ingress network QoS policy defines the match criteria used to determine the Flow Class of each packet, entering via an SDP binding (i.e. PW). The operator can configure ingress network QoS policy for the service.
Page 112: Common Configuration Tasks
Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.4.1 Common Configuration Tasks This section provides a brief overview of the tasks that must be performed to configure the VLL services and provides the CLI commands. 1 Associate the service with a customer ID.
Page 113: Configure Epipe Service Mtu Attribute
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services [cbs cbs-size] [pbs pbs-size] no rate-limit egress-network qos policy-id no qos ingress qos policy-id no qos ingress-network qos policy-id no qos sgt-qos policy-id no sgt-qos 4.4.2.2 Configure Epipe Service MTU Attribute Use the following CLI syntax to configure the MTU for the Epipe service.
Page 114 Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide This example configures a distributed service between ALA-1 and ALA-2. A:ALA-1> configure>service# epipe 5500 customer 5 create configure>service>epipe$description "Distributed epipe service to east coast" configure>service>epipe# sap lt:1/1/1:550 create configure>service>epipe>sap# ingress configure>service>epipe>sap>ingress# filter ip 1 configure>service>epipe>sap>ingress# exit...
Page 115: Configuring Sdp Bindings
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services exit exit ---------------------------------------------- A:ALA-2>configure>service# Configure ‘restricted-tagging’ on an SAP When 'restricted-tagging' is enabled on a SAP, only double-vlan-tagged packets arriving at the SAP will be forwarded. Packets with outer TPID as 0x8100 and inner TPID 0x8100 are alone considered as double-vlan-tagged packets.
Page 116: Figure 12 Sdps - Uni-Directional Tunnels
Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Figure 12 SDPs — Uni-Directional Tunnels ALA-1 ALA-2 SDP 3 demux SPOKE-SDP 3 Epipe 2 for customer 6 SDP 2 SPOKE-SDP 2 Epipe 2 for demux customer 6 Use the following CLI syntax to create a spoke SDP binding with an Epipe service: configure>service# epipe service-id [customer customer-id] spoke-sdp sdp-id:vc-id [vc-type {ether|vlan}]...
Page 117 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services ingress filter ip 1 exit egress filter ip 2 exit exit spoke-sdp 2:123 create ingress vc-label 6600 exit egress vc-label 5500 exit exit no shutdown exit ---------------------------------------------- A:ALA-1>configure>service# A:ALA-2>configure>service# info ----------------------------------------------...
Page 118: Sdp Bindings
Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.4.3 Configuring Management Points (MEPs/MIPs) for Ethernet CFM on SDP bindings Two steps are required to configure the CFM in an EPIPE network: 1 The MD and MA need to be created first 2 The MEP/MIP can be created in the EPIPE service instance, by associating it to a SDP binding and adding to the defined MD and MA.
Page 119: Using Spoke Sdp Control Words
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services no shutdown 4.4.4 Using Spoke SDP Control Words When control word is enabled, the Admin Control Word is set to Preferred. It is necessary that both sides of the VLL have control word enabled or disabled for the pipe to be up.
Page 120: Service Management Tasks
Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.4.5 Service Management Tasks This section discusses the following service management tasks: • Modifying Epipe Service Parameters • Disabling an Epipe Service • Re-enabling an Epipe Service •...
Page 121: Re-Enabling An Epipe Service
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services configure>service>epipe# shutdown configure>service>epipe# exit 4.4.5.3 Re-enabling an Epipe Service Use the following command to re-enable an Epipe service that was shut down: configure>service> epipe service-id no shutdown Example: configure>service# epipe 2 configure>service>epipe# no shutdown...
Page 122: Vll Services Cli Command Reference
Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.5 VLL Services CLI Command Reference This section shows the following command hierarchies: • Epipe Service Configuration Commands • Show Commands • Clear Commands 4.5.1 Epipe Service Configuration Commands configure —...
Page 123: Show Commands
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services — ccm-ltm-priority priority — no ccm-ltm-priority — low-priority-defect{allDef|macRemErrXcon|remErrXcon|errXcon|xcon|noXcon} — mac-address mac-address — no mac-address — [no] shutdown — [mac mac-address] — default-mac — no — vlan-dot-1q-etype etype —...
Page 124: Generic Commands
Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.6.1 Generic Commands 4.6.1.1 shutdown Table 51 shutdown command Item Description Syntax [no] shutdown Context configure>service>epipe configure>service>epipe>sap configure>service>epipe>spoke-sdp configure>service>epipe>spoke-sdp>eth-cfm>mep Description This command administratively disables an entity. When disabled, an entity does not change, reset, or remove any configuration settings or statistics.
Page 125: Vll Global Commands
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services Item Description Context configure>service>epipe configure>service>epipe>sap Description This command creates a text description stored in the configuration file for a configuration context. The description command associates a text string with a configuration context to help identify the content in the configuration file.
Page 126: Service-Mtu
Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters service-id — The unique service identification number identifying the service in the service domain. This ID must be unique to this service and may not be used for any other service of any type.
Page 127: Sgt-Qos
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services Table 55 MTU Values for Specific VC Types VC-Type Example Advertised MTU Service MTU Ethernet 1514 1500 Ethernet (with preserved dot1q) 1518 1504 VLAN (dot1p transparent to MTU value) 1514 1500 VLAN (QinQ with preserved bottom Qtag)
Page 128 Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command creates a Service Access Point (SAP) within a service. A SAP is a combination of port and encapsulation parameters which identifies the service access point on the interface and within the ISAM.
Page 129: Restricted-Tagging
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services 4.6.3.2 restricted-tagging Table 58 restricted-tagging command Item Description Syntax restricted-tagging no restricted-tagging Context configure>service>epipe configure>service>epipe>sap Description This command enables restricted-tagging for the SAP. 4.6.4 Service Filter and QoS Policy Commands 4.6.4.1 egress Table 59...
Page 130: Ingress
Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.6.4.3 ingress Table 61 ingress command Item Description Syntax ingress Context configure>service>epipe configure>service>epipe>sap Description This command enables the context to configure ingress parameters for the service and the SAP.
Page 131: Qos
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services Item Description Description This command associates an IP or MAC filter policy with an ingress or egress Service Access Point (SAP). Filter policies control the forwarding and dropping of packets based on IP or MAC matching criteria.
Page 132: Qos
Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters policy-id — The access QoS policy ID to associate with the service on ingress. The policy ID must already exist. Values: 1 — 65535 (2 of 2) 4.6.4.7 Table 65...
Page 133: Rate-Limit
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services 4.6.4.8 rate-limit Table 66 rate-limit command Item Description Syntax rate-limit cir cir-rate pir pir-rate [cbs cbs-size] [pbs pbs-size] no rate-limit Context configure>service>epipe>egress Description This command defines the aggregate egress rate limit for the Epipe service. It applies to traffic associated to the service which is egressing on regular ports (network ports).
Page 134 Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command binds a service to an existing Service Distribution Point (SDP). A spoke SDP is treated like the equivalent of a traditional bridge “port” where flooded traffic received on the spoke SDP is replicated on all other “ports”...
Page 135: Control-Word
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services 4.6.5.2 control-word Table 68 control-word command Item Description Syntax [no] control-word Context configure>service>epipe>spoke-sdp Description This command indicates whether the control word is used or not. The value of the control word is negotiated with the peer.
Page 136: Egress
Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.6.5.4 egress Table 70 egress command Item Description Syntax egress Context configure>service>epipe>spoke-sdp Description This command configures the egress SDP context. 4.6.5.5 ingress Table 71 ingress command Item Description Syntax ingress...
Page 137: Vc-Label
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services 4.6.5.7 vc-label Table 73 vc-label command Item Description Syntax [no] vc-label egress-vc-label Context configure>service>epipe>spoke-sdp>egress Description This command configures the egress VC label. Parameters vc-label — A VC egress value that indicates a specific connection. Values: 16 —...
Page 138: Eth-Cfm
Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command specifies an explicit dot1q value used when encapsulating to the SDP far end. When signaling is enabled between the near and far end, the configured dot1q tag can be overridden by a received TLV specifying the dot1q value expected by the far end.
Page 139: Ccm-Enable
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services Item Description Parameters mep-id - MEP Identifier Values: 1...8191 md-index - Maintenance Domain Identifier Values: 1...4294967295 ma-index - Maintenance Association Identifier. Values: 1...4294967295 direction - Specifies the direction of the MEP. Values: up/down Default value: down (2 of 2)
Page 140: Low-Priority-Defect
Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.6.5.14 low-priority-defect Table 80 low-priority-defect command Item Description Syntax low-priority-defect { allDef | macRemErrXcon | remErrXcon | errXcon | xcon | noXcon} Context configure>service>epipe>spoke-sdp>eth-cfm>mep Description This command specifies the lowest priority defect that is allowed to generate a fault alarm. Default macRemErrXcon Parameters...
Page 141: Mip
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services 4.6.5.16 Table 82 mip command Item Description Syntax mip [mac mac-address] mip default-mac no mip Context configure>service>epipe>spoke-sdp>eth-cfm Description This command enables/disables Maintenance Intermediate Points (MIP) Parameters mac-address - The MAC address of the MIP in xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx format. Value: xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx default-mac - keyword.
Page 142: Show Commands
Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.6.6 Show Commands 4.6.6.1 egress-label Table 84 egress-label command Item Description Syntax egress-label start-label [end-label] Context show>service Description This command displays services using the range of egress labels. If only the mandatory start-label parameter is specified, only services using the specified label are displayed.
Page 143: Ingress-Label
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services 4.6.6.2 ingress-label Table 86 ingress-label command Item Description Syntax ingress-label start-label [end-label] Context show>service Description This command displays services using the range of egress labels. If only the mandatory start-label parameter is specified, only services using the specified label are displayed.
Page 144: Sap-Using
Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.6.6.3 sap-using Table 88 sap-using command Item Description Syntax sap-using [sap sap-id] sap-using [ingress | egress] filter filter-id Context show>service Description This command displays SAP information. If no optional parameters are specified, the command displays a summary of all defined SAPs. The optional parameters restrict output to only SAPs matching the specified properties.
Page 145: Sdp
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services Table 89 Show Service SAP Output Fields Label Description Port ID The ID of the access or hybrid port where the SAP is defined. Svc ID The service identifier. Sap MTU The SAP MTU value.
Page 146: Sdp-Using
Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Table 91 Show Service SDP Output Fields Label Description SDP Id The SDP identifier. Adm MTU Specifies the desired largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented.
Page 147: Table 93 Show Service Sdp-Using Output Fields
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services Item Description Parameters sdp-id — Displays only services bound to the specified SDP ID. Values: 1 — 17407 vc-id — The virtual circuit identifier. Values: 1 — 4294967295 far-end ip-address —...
Page 148: All
Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters service-id — The service identification number that identifies the service in the domain. all — Display detailed information about the service. base — Display basic service information. labels —...
Page 149 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services Label Description Flags Specifies the conditions that affect the operating status of this SAP. Display output includes: ServiceAdminDown, SapAdminDown, InterfaceAdminDown, PortOperDown, PortMTUTooSmall, L2OperDown, SapIngressQoSMismatch, SapEgressQoSMismatch,RelearnLimitExceeded, RxProtSrcMac, ParentIfAdminDown, NoSapIpipeCeIpAddr, TodResourceUnavail, TodMssResourceUnavail, SapParamMismatch, CemSapNoEcidOrMacAddr, StandByForMcRing, ServiceMTUTooSmall, SapIngressNamedPoolMismatch,...
Page 150 Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Service Id The service identifier. Port Id The ID of the access or hybrid port where this SAP is defined. Description Generic information about the SAP. Encap Value The value of the label used to identify this SAP on the access or hybrid port.
Page 151: Base
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services Label Description Out profile The number of out-of-profile packets or octets (rate above CIR) forwarded. forwarded Out profile dropped The number of out-of-profile packets or octets discarded. Service Access Points Managed by Service Specifies the service-id of the management VPLS managing this SAP.
Page 152: Labels
Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Label Description SAP Count The number of SAPs defined on the service. SDP Bind Count SDP Bind Count Identifier Specifies the service access (SAP) and destination (SDP) points. Type Specifies the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on the SDP.
Page 153: Sap
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services 4.6.6.10 Table 101 sap command Item Description Syntax sap sap-id detail Context show>service>id Description This command displays information for the SAPs associated with the service. If no optional parameters are specified, a summary of all associated SAPs is displayed.
Page 154: Sdp
Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.6.6.11 Table 103 sdp command Item Description Syntax sdp sdp-id far-end ip-addr detail Context show>service>id Description Displays information for the SDPs associated with the service. If no optional parameters are specified, a summary of all associated SDPs is displayed. Parameters sdp-id —...
Page 155: Clear Commands
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services Label Description Signaling Specifies the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on this SDP. Admin State The administrative state of the Keepalive process. Oper State The operational state of the Keepalive process.
Page 156: Counters
Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sdp-id — The spoke SDP ID to be reset. Values: 1 — 17407 vc-id — The virtual circuit ID on the SDP ID to be reset. Values: 1 —...
Page 157: Virtual Private Lan Service
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5 Virtual Private LAN Service 5.1 In This Chapter 5.2 VPLS used in the NT 5.3 ISAM VPLS implementation 5.4 VPLS feature enhancements 5.5 Configuring a VPLS Service with CLI 5.6 Configuration Overview 5.7 Configuration Workflow 5.8 Configuring VPLS Components...
Page 158: Vpls Used In The Nt
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.2 VPLS used in the NT The ISAM NT makes use of the m-VPLS service, the v-VPLS service for VLAN-based services over a EMAN network and the VPLS service for L2 VPN using PW over a MPLS/IP network.
Page 159: Isam Vpls Implementation
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Hybrid ports can only be of the regular category. They inherit the features of both network ports and regular access ports. Access ports are defined for the IHub as residential or regular, by a port table that is auto-created by the system at startup time.
Page 160: V-Vpls
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide To support L2CP protocols running on top of a LAG, m-VPLS SAPs must be created on the LAG itself. 5.3.2 v-VPLS 5.3.2.1 v-VPLS usage The v-VPLS forwarders emulate the ISAM bridging service in the IHUB. Typical of bridging, a v-VPLS operates in the context of a VLAN.
Page 161: Figure 15 Nt V-Vpls Forwarding
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Figure 15 NT v-VPLS forwarding DHCP snooping/ Static config. Relay RSTP/ Network ports MSTP ports ibridge IGMP snooping m-VPLS DHCP snooping/ Static config. Relay EMAN ibridge Network v-VPLS IP Edge DHCP snooping/...
Page 162: V-Vpls Saps
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide • Forwarding Information Base (FIB) management features on a per service level including: • Configurable FIB size limit. • FIB size alarms. • MAC learning disable. • User-to-user communication control for services configured on residential (user) ports.
Page 163: Mix Of Vpls And Vprn
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service The following apply to v-VPLS SAP configuration: • An SAP can only be configured on dot1q Ethernet encapsulation access/hybrid ports. • The v-VPLS operates in the context of a homogeneous VLAN ID, where all Ethernet dot1q v-VPLS SAPs must refer to the v-VPLS VLAN ID.
Page 164: Residential And Regular Port Usage
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.3.2.4 Residential and regular port usage The v-VPLS behavior distinguishes between the user-side (SAPs built on residential ports) and the network-side (SAPs built on regular ports or on LAGs made of regular ports), to secure control over MAC learning capabilities, and enable the ability to control user-to-user communication.
Page 165: Figure 18 Vprn And V-Vpls Virtual Port Interconnection Model
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Figure 18 VPRN and v-VPLS virtual port interconnection model v-VPLS Vlan 17 My-Own-MAC@ VPRN_1 v-VPLS Vlan 19 My-Own-MAC@ VPRN_2 v-VPLS Vlan 23 My-Own-MAC@ Legend: Virtual port Figure 19 SAPs and virtual port object model v-VPLS All SAPs must...
Page 166: V-Vpls Mac Learning And Packet Forwarding
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide The virtual port plays the role of a physical connection between a v-VPLS and VPRN. The virtual port is auto-created at NT start-up time and is automatically associated with each v-VPLS instance when the v-VPLS is created.
Page 167: V-Vpls Traffic Processing
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service • When a frame is received from an SAP and the source MAC address conflicts with an entry in the FDB which was already self-learned (a dynamic FDB entry) on another SAP: •...
Page 168: Table 109 L2Cp And Lacp Destination Mac Address Definitions
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Table 109 L2CP and LACP destination MAC address definitions Frame type Destination MAC address L2CP pause frames 01-80-C2-00-00-01 L2CP frames L2CP frames include: • 01-80-C2-00-00-00 through 01-80-C2-00-00-0F •...
Page 169: Vpls
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.3.3 VPLS 5.3.3.1 VPLS usage Virtual Private LAN Service (VPLS) as described in Internet Draft draft-ietf-ppvpn-vpls-ldp-01.txt, is a class of virtual private network service that allows the connection of multiple sites in a single bridged domain over a provider-managed IP/MPLS network.
Page 170: Vpls Mac Learning And Packet Forwarding
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide VPLS is provided over MPLS by: • Connecting bridging-capable provider edge routers with a full mesh of MPLS LSP (label switched path) tunnels. • Negotiating per-service VC labels using draft-Martini encapsulation. •...
Page 171: Vpls Packet Walkthrough
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.3.3.3 VPLS Packet Walkthrough This section provides an example of VPLS processing of a customer packet sent across the network from site-A, which is connected to PE-Router-A, to site-B, which is connected to PE-Router-C (see Figure 20).
Page 172: Figure 22 Network Port Egress Packet Format And Flooding
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 2 PE-Router-A learns the source MAC address in the packet and creates an entry in the FIB table that associates the MAC address to the service access point (SAP) on which it was received.
Page 173: Figure 23 Access Port Egress Packet Format And Lookup
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Core Router Switching • All the core routers ('P' routers in IETF nomenclature) between PE-Router-A and PE-Rout- er-B and PE-Router-C are Label Switch Routers (LSRs) that switch the packet based on the transport (outer) label of the packet until the packet arrives at far-end PE-Router.
Page 174: Vpls Feature Enhancements
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.4 VPLS feature enhancements This section describes v-VPLS and m-VPLS supported enhancements and features. 5.4.1 Local and Remote Aging Timers Like a Layer 2 switch, learned MACs within a VPLS instance can be aged out if no packets are sourced from the MAC address for a specified period of time (the aging time).
Page 175: Fib Size
5.4.7 VPLS and Spanning Tree Protocol Nokia’s VPLS service emulates a bridged or switched Ethernet Layer 2 network. The ISAM uses m-VPLS SAPs configured on ports or a LAG to forwards Ethernet packets into the m-VPLS service. The ISAM participating in the service learns where the customer MAC addresses reside, on ingress SAPs.
Page 176: Spanning Tree Operating Modes
If SAPs are connected together, either through misconfiguration or for redundancy purposes, loops can form and flooded packets can keep flowing through the network. Nokia’s implementation of the Spanning Tree Protocol (xSTP) is designed to remove these loops from the VPLS topology. This is done by putting one or several SAPs in the discarding state.
Page 177: Multiple Spanning Tree
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service correctly. This would result in a slow transition to a forwarding state (30 seconds). For this reason, in the comp-dot1w mode, these BPDUs contain the port's port priority vector (conforms to 802.1w).
Page 178: Mstp General Principles
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.4.7.4 MSTP General Principles MSTP represents modification of RSTP which allows the grouping of different VLANs into multiple MSTIs. To enable different devices to participate in MSTIs, they must be consistently configured.
Page 179: Xstp High Availability
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service The T-LDP control plane behavior will be the same as the control word for VLL services. This means that an ISAM PE will not be able to negotiate with the peer PE whether the control word should be used.
Page 180: Figure 24 Management Model
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.4.8.3 Ingress Network Classification (only VPLS) A service ingress network QoS policy defines the match criteria used to determine the Flow Class of each packet, entering via an SDP binding (i.e. PW). The operator can configure ingress network QoS policy for the service.
Page 181: Pm Counters Per Sap
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service The VPLS management VRF only supports routing packets to locally attached hosts. That is, no next-hops can be statically specified and no routing protocols can be activated. To address the VPLS management VRF, the router instance vpls-management must be specified in CLI commands.
Page 182 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide When using the per service configurable TPID for a VPLS or EPIPE service (not for v-VPLS services), there are the following known limitations: • It is not possible to drop dataplane traffic in case the TPID does not match the service TPID (vlan-dot1q-etype).
Page 183: Figure 25 Configurable Tpid
5.4.12 External Packet Forwarding (EPF) External Packet Forwarding is an Nokia proprietary feature to support Lawful intercept in a H.248 based voice network. To support this in IHUB, the IP address of a router 'R' will be configured in a v-VPLS which carries voice traffic.
Page 184: Figure 26 External Packet Forwarding
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Figure 26 External Packet Forwarding Router “R” ISAM-V MPLS VPN VoIP 7600 source dest VoIP platform source dest VLAN Voice & H.248 VLAN OAM NT I/O interface ISAM 5.4.12.1 Configuration Model...
Page 185: Configuring A Vpls Service With Cli
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service When the EPF IP is already configured on the v-VPLS, the following restrictions are enforced: • a virtual port SAP cannot be removed from the VPRN / IES interface, •...
Page 186: Configuration Overview
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.6 Configuration Overview The ISAM supports configuration of three types of VPLS services: • multiple v-VPLS instances can be configured to support L2 data frame forwarding between the user side and network sides via the IHub and VPRN interface reach extension •...
Page 187 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service The following configuration elements can be specified for m-VPLS after the service is created: • service description • STP, RSTP or MSTP instances • admin status up or down Since the m-VPLS does not forward traffic, it has no Note —...
Page 188: Configuration Workflow
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide *A:ALA-2>config>service# info ---------------------------------------------- vpls 9000 customer 6 create description "This is a distributed VPLS." def-mesh-vc-id 750 shutdown exit sap lt:1/1/5:16 create description "VPLS SAP" exit spoke-sdp 2:22 create exit mesh-sdp 8:750 create exit...
Page 189: Configuring Vpls Components
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 4 Define mesh/spoke SDP's for the VPLS (optional) • Associate the service to an existing SDP 5 Modify STP default parameters for the m-VPLS (optional). 6 Modify v-VPLS parameters such as user-to-user communication, mac learning and aging, FDB database size (optional).
Page 190 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide exit exit no shutdown ---------------------------------------------- *A:ALA-1>configure>service>vpls# Multiple v-VPLS instances can be configured for the ISAM. Note that the customer ID must be specified when creating the service, but is optional when making modifications.
Page 191 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service • The service ID must be unique to the service domain. Specifying an existing service ID enters the editing context for that service ID. • The admin status is down when the service is created and must be enabled using the no shutdown command.
Page 192: Configuring V-Vpls/Vpls Parameters
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide • Restricted MAC move is enabled (i.e MACs learned on regular ports overrule MACs learned on residential ports; MACs learned on residential ports cannot override MACs learned on regular ports). •...
Page 193: Mac Learning And Aging
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.8.2.3 MAC learning and aging Learning of new MAC addresses in the v-VPLS/VPLS forwarding database (FDB) can be enabled and disabled for the service instance using the disable-learning command.
Page 194: User-To-User Communication
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide • query-interval: The configured default value for (dynamic) MR SAPs when these SAPs cannot learn the query-interval from the received QUERY messages (for example, because these are not filled in the QUERY message). The system assumes an external querier is shutdown when no QUERY is ×...
Page 195: Unrestricted Mac Move
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.8.2.6 Unrestricted MAC move The VPLS behavior distinguishes between the user side and network side, to secure control over MAC learning capabilities. MAC learning on regular access ports or on SDP bindings has by default priority over MACs learned on residential SAPs.
Page 196: External Packet Forwarding
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide sap nt-a:xfp:2:500 create exit no shutdown --------------------------------------------------------------- >configure>service>vpls# >configure>port>nt-a:xfp:2:500>ethernet --------------------------------------------------------------- use-vlan-dot1q-etype ------------------------------------------------------------------- To disable the use of an alternate TPID, use the no vlan-dot1q-etype command. >configure>service>vpls# info ------------------------------------------------------------- [no] vlan-dot1q-etype <etype>...
Page 197: Configuring Spanning Tree Protocols On M-Vpls
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service extfwd device-ip 10.1.1.2 exit shutdown exit exit vprn 1001 customer 1 create shutdown interface "epf_vprn" create address 10.1.1.1/30 sap nt:vp:1:1000 create exit exit exit ----------------------------------------------- 5.8.3 Configuring Spanning Tree Protocols on m-VPLS RSTP and MSTP are supported on the m-VPLS only, not on a v-VPLS.
Page 198: Configuring Stp Bridge Parameters
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.8.3.1 Configuring STP Bridge Parameters Modifying some of the Spanning Tree Protocol parameters allows the operator to balance STP between resiliency and speed of convergence extremes. Modifying particular parameters, mentioned below, must be done in the constraints of the following two formulae: 2 x (Bridge_Forward_Delay - 1.0 seconds) >= Bridge_Max_Age...
Page 199 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service • mstp-comp-2003 Compliant with the Multiple Spanning Tree Protocol specified in IEEE 802.1Q-REV/D3.0-04/2005 but with some changes to make it backwards compatible to 802.1Q 2003 edition and IEEE 802.1w. •...
Page 200 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide configure>service>vpls service-id# stp max-age max-info-age • Range: 6 to 40 seconds • Default: 20 seconds • Restore Default: no max-age Forward Delay RSTP, as defined in the IEEE 802.1D-2004 standards, will normally transition to the forwarding state via a handshaking mechanism (rapid transition), without any waiting times.
Page 201 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Hold Count The hold-count command configures the peak number of BPDUs that can be transmitted in a period of one second. configure>service>vpls service-id# stp hold-count count-value • Range: 1 to 10 •...
Page 202: Configuring Vpls Saps
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.8.4 Configuring VPLS SAPs A default QoS policy is applied to each ingress and egress SAP. Additional QoS policies can be configured in the configure>qos context.VPLS services use SAPs to associate the service with a dot1q Ethernet encapsulation access physical port or LAG.
Page 203: Vpls Sap Configuration Example
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.8.4.2 VPLS SAP configuration example To configure a local VPLS service, enter the sap sap-id command twice with different port IDs in the same service configuration. configure service vpls <service-id> sap {<port-id> | <lag-id>}:<vlan-id> create The following CLI command syntax to create or modify an SAP: configure service vpls <service-id>...
Page 204 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide For SDP binding information, see “Configuring SDP Bindings”. The following example displays a configuration of VPLS SAPs configured for ALA-1, ALA-2, and ALA-3. *A:ALA-1>config>service# info -------------------------------------------- vpls 9000 customer 6 vpn 750 create description "Distributed VPLS services."...
Page 205: Configuring Vpls Sap Parameters
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.8.5 Configuring VPLS SAP Parameters After an SAP is created for a service, you can modify SAP parameters including IP and MAC filter policies, static MAC, and SAP specific RSTP/MSTP parameters. 5.8.5.1 Configuring egress and ingress filter policies on an You can associate an IP or MAC filter policy with an ingress or egress Service...
Page 206 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide • SAP Admin Down An administratively down state allows a service provider to prevent an SAP from becoming operationally blocked. BPDUs will not originate out the SAP towards the customer.
Page 207 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service The default value for SAP priority is 128. This parameter can be modified within a range of 0 to 255, 0 being the highest priority. Masking causes the values actually stored and displayed to be 0 to 240, in increments of 16.
Page 208: Configuring Sap-Specific Igmp Parameters
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.8.5.4 Configuring SAP-specific IGMP Parameters The following SAP-specific IGMP parameters can be configured: • mrouter-port: This command specifies whether a multicast router is attached behind this SAP. configure service vpls service-id sap sap-id igmp-snooping mrouter-port When configuring an SAP as an mrouter-port, then IGMP REPORTS generated by the IGMP subsystem of the containing v-VPLS/VPLS are sent out on this SAP.
Page 209 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service • query-interval: This command configures the interval between two consecutive general QUERIES sent out by the IGMP subsystem on this SAP. configure service vpls service-id sap sap-id igmp-snooping query-interval seconds The configured query-interval must be greater than the configured query-response-interval.
Page 210: Configuring "Restricted-Tagging" On An Sap
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.8.5.5 Configuring “restricted-tagging” on an SAP When “restricted-tagging” is enabled on an SAP, only double-vlan-tagged packets arriving at the SAP will be forwarded. Only packets with outer TPID as 0x8100 and inner TPID 0x8100 are considered as double-vlan-tagged packets.
Page 211 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service When creating the MEP, MDs and MAs are associated and in addition, the following parameters are required: • MEP-ID - The ID value used to identify the MEP in the MA. This ID value must be listed in the remote-MEP-iD list in the MA configuration of the other PE router.
Page 212: Enabling Statistics Collection And Pm Collection On An Sap
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.8.5.7 Enabling Statistics collection and PM collection on an SAP Statistics collection and PM collection are enabled on an SAP when “enable-stats” is configured on that SAP. The operator can then monitor ingress packets/octets and egress packets/octets on an SAP.
Page 213: Operationally Disabled
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.8.6.1 Operationally Disabled Operationally disabled is the normal operational state for STP on an SAP in a VPLS that has any of the following conditions: • VPLS state administratively down •...
Page 214: Configuring Sdp Bindings
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.8.7 Configuring SDP Bindings A spoke SDP is treated like the equivalent of a traditional bridge port where flooded traffic received on the spoke SDP is replicated on all other "ports" (other spoke and mesh SDPs or SAPs) and not transmitted on the port it was received (unless a split horizon group was defined on the spoke SDP).
Page 215: Figure 27 Uni-Directional Tunnels
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Figure 27 Uni-Directional Tunnels ALA-1 ALA-2 MESH-SDP 3 VPLS 9000 VPLS 9000 MESH-SDP 4 Customer 6001 Customer 6001 Spoke-SDP 21 Spoke-SDP 11 Spoke-SDP 22 Spoke-SDP 10 MTU A MTU C VPLS 9000 Customer 6001...
Page 216 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide vlan-vc-tag 0..4094 no shutdown static-mac ieee-address vlan-vc-tag [0..4094] The following displays SDP binding configurations for ALA-1, ALA-2, and ALA-3 for VPLS service ID 9000 for customer 6: *A:ALA-1>config>service# info ---------------------------------------------- vpls 9000 customer 6 create...
Page 217: Service Management Tasks
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service exit spoke-sdp 2:22 create exit mesh-sdp 5:750 create exit mesh-sdp 7:750 create exit no shutdown exit ---------------------------------------------- *A:ALA-3>config>service# 5.9 Service Management Tasks This section discusses the following service management tasks: •...
Page 218: Enabling And Disabling Vpls Entities
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide shutdown exit sap lt:1/1/5:22 create description “VPLS SAP” exit no shutdown ---------------------------------------------- *A:ALA-1>configure>service>vpls# To display a list of services, use the show service service-using vpls command. Enter the parameter such as description and/or SAP command syntax, and then enter the new information.
Page 219: Deleting A Vpls Service Or Sap
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service For example: configure service vpls 1 configure service vpls 1 shutdown configure>service>vpls1>exit 5.9.3 Deleting a VPLS Service or SAP A VPLS service cannot be deleted until SAPs are unbound (deleted), interfaces are shutdown, and the service is shutdown on the service level.
Page 220: Clearing Vpls Operational Data
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide *A:SetupCLI# show service id 17 fdb ==================================================================== Forwarding Database, Service 17 ==================================================================== Service Id : 17 Service Type : v-VPLS Table Size : 250 Total Count Learned Count Static Count OAM-learned Count : 0 Host-learned Count: 0...
Page 221: Showing Vpls Sap Operational Data
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.9.6 Showing VPLS SAP operational data The operator can show SAP operational data including the following: • Summary information • All information • STP statistics • SAP statistics •...
Page 222: Bgp Ad Overview
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.10.1 BGP AD Overview The BGP protocol establishes neighbor relationships between configured peers. An open message is sent after the completion of the three-way TCP handshake. This open message contains information about the BGP peer sending the message.
Page 223: Table 110 Bgp Ad Nlri Versus Ip Vpn Nlri
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Table 110 BGP AD NLRI versus IP VPN NLRI BGP AD NLRI Usage IP VPN NLRI Usage Route Distinguisher (8 Octets) Route Distinguisher (8 Octets) VSI id (4) (IP Prefix) IP Prefix Network Layer Reachability Information (NLRI) is exchanged between BGP peers indicating how to reach prefixes.
Page 224: Bgp-Ad And Target Ldp (T-Ldp) Interaction
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide AII Type Length Value SAII Value (continued) AII Type Length Value TAII Value (continued) (2 of 2) Each of the FEC fields are designed as a sub-TLV equipped with its own type and length providing support for new applications.
Page 225: Figure 28 Bgp-Ad And T-Ldp Interaction
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Figure 28 BGP-AD and T-LDP Interaction Reflector Cluster VPN 10 VPN 10 Legend: I-BGP Session 24382 5.10.4 SDP Usage Service Access Points (SAP) are linked to transport tunnels using Service Distribution Points (SDP).
Page 226: Automatic Creation Of Sdps
The Nokia implementation provides for safe handling of pseudowire templates. Changes to the pseudowire templates are not automatically propagated. Tools are provided to evaluate and distribute the changes. The following command is used to distribute changes to a “pw-template”...
Page 227: Figure 29 Bgp Vpls Solution
Both of these changes are service affecting. Other changes will not be service affecting. 5.11 BGP VPLS The Nokia BGP VPLS solution, compliant with RFC 4761, is described in this section. Figure depicts the service representation for BGP VPLS mesh.
Page 228: Pseudowire Signaling Details
• VE Block size (VBS) — defines how many contiguous pseudowire labels are reserved starting with the Label Base • Nokia implementation always uses a value of eight • Label Base (LB) — local allocated label base • The next eight labels are allocated for remote PEs Thjs BGP update communicates to the other PE(s) to accept the RT in order to reach (VE-ID=x), use a pseudowire label of LB + VE-ID—VBO using the BGP NLRI for...
Page 229: Table 112 Layer2 Info Extended Community
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Assuming that VE-ID=10 is configured in another PE4 the following procedures applies: • PE4 sends BGP Update with the new VE-ID in the network that will be received by all the other participating PEs, including PE1.
Page 230: Table 113 Control Flags Bit Vector
VPLS packets to this PE, depending on whether S is 1 or 0, respectively • C — a Control work MUST or MUST NOT be present when sending VPLS packets to this PE, depending on whether C is 1 or 0, respectively. By default, Nokia implementation uses 0 •...
Page 231: Bgp Vpls Configuration Procedure
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.11.2 BGP VPLS Configuration Procedure BGP VPLS configuration requires the setup of the MPLS infrastructure and VPLS instance: • create LSPs • create SDPs if manually provisioned ones are required •...
Page 232: Usage Case Example
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide • Layer 2 MTU — derived from service vpls service-mtu parameter • The same value must be used in all related BGP VPLS instances in the Remote PEs to ensure the related pseudowires will come up.
Page 233: Configuring Bgp Auto-Discovery
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Including the service id is not mandatory but it is recommended as it will reduce the scope of the command to only the affect service id. 5.12 Configuring BGP Auto-Discovery This section provides important information to explain the different configuration options used to populate the required BGP AD and generate the LDP generalized pseudowire-ID FEC fields.
Page 234: Figure 30 Bgp Ad Configuration Example
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Figure 30 BGP AD Configuration Example L2VPN BGP AD VPLS-id: 65535:100 VLS-id: 1.1.1.134 L2VPN BGP AD RD: 65535:100 VSI-id: 1.1.1.6 65535:100 65535:100 RT: 65535:100 PE134 Next-hop: Self MPLS-id= MPLS-id= 1.1.1.134/32...
Page 235: Table 114 Bgp-Ad Cli Command Tree
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service *A:PE6>config>service>vpls# info ---------------------------------------------- route-distinguisher 65535:100 route-target export target:65535:100 import target:65535:100 pw-template-bind 1 exit bgp-ad vpls-id 65535:100 vsi-id prefix 1.1.1.6 no shutdown exit sap 1/1/20:600.* create exit no shutdown ---------------------------------------------- *A:PE6>config>service>vpls# In many cases, VPLS connectivity is based on a pseudowire mesh.
Page 236: Table 116 Bgp Parameters And Sdp Bindings In Use Example Display: Pers6
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide PERs6># (2 of 2) Table 116 BGP parameters and SDP bindings in use example display: PERs6 PERs6># show service l2-route-table Services: L2 Route Information — Summary Service Svc Id L2-Routes (RD-Prefix) Next Hop...
Page 237: Figure 31 Bgp Vpls Example
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Figure 31 BGP VPLS Example VPLS PE-24 VPLS IP/MPLS PE-26 VPLS PE-25 24384 The BGP VPLS is configured in the PE24, PE25, and PE26 using the commands shown in the following CLI examples.
Page 238: Ldp Signaling
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide exit no shutdown exit sap 1/1/19:600.* create exit no shutdown ---------------------------------------------- Example #3: *A:PE25>config>service>vpls# *A:PE26>config>service>vpls# info ---------------------------------------------- route-distinguisher 65026:600 route-target export target:65019:600 import target:65019:600 pw-template-bind 1 exit bgp-vpls max-ve-id 100 ve-name 26...
Page 239: Figure 32 Bgp Ad Triggering Ldp Functions
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Figure 32 BGP AD Triggering LDP Functions pw-template 1 pw-template 1 vpls 100 Customer 1 create vpls 100 Customer 1 create service-mtu 1478 service-mtu 1478 bgp-ad bgp-ad vpls-id 65535:100 vpls-id 65535:100 pw-template-bind 1...
Page 240: Table 119 Pw-Template Cli Tree
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Legend U — Label In Use, N — Label Not In Use, W — Label Withdrawn S — Status Signaled Up, D — Status Signaled Down E — Epipe Service, V — VPLS Service, M — Mirror Service A —...
Page 241: Table 120 Pw-Template-Bind Cli Syntax
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service A pw-template-bind command configured within the VPLS service under the bgp-ad subcommand is a pointer to the pw-template that should be used. If a VPLS service does not specify an import-rt list, then that binding applies to all route targets accepted by that VPLS.
Page 242 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.14 Configuring BGP Auto-Discovery with Non-Persistency BGP-AD configuration can be made non-persistently by configuring the MIB object svsConfigPersistentControl to false using SNMP set along with the VPLS service creation.
Page 243: Vpls Service Cli Command Reference
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.15 VPLS Service CLI Command Reference This section shows the following command hierarchies: • Global Commands • SAP Commands • Show Commands • Clear Commands • Debug Commands 5.15.1 VPLS Service Configuration Commands 5.15.1.1...
Page 244 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide — egress-network — policy-id — no — [no] endpoint endpoint-name [create] — description description-string — [no] ignore-standby-signaling — [no] revert-time {revert-time | infinite} — [no] static-mac ieee-address [create] —...
Page 245 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service — [no] shutdown — [no] static-mac ieee-mac-address — [no] vlan-vc-tag 0..4094 — mfib-table-size table-size — no mfib-table-size — no propagate-mac-flush — remote-age aging-timer — no remote-age — no send-flush-on-failure —...
Page 246: Sap Commands
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide — mst-revision revision-number — no mst-revision — priority bridge-priority — no priority — [no] shutdown — vlan-dot1q-etype etype — [no] vlan-dot1q-etype — [no] user-user-com — [no] pw-template policy-id [create] —...
Page 247: Show Commands
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service — robust-count count — no robust-count — [no] send-queries — static — group grp-ip-address — [no] group — source ip-address — [no] source — [no] starg — version version —...
Page 248: Clear Commands
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide — mfib [brief] [ip] — mfib group grp-address — mstp-configuration — [sap-id [detail | sap-stats]] — [sap-id curr-15min-stats] — [sap-id curr-day-stats] — [sap-id prev-15min-stats [interval-number interval-number]] — [sap-id prev-day-stats [interval-number interval-number]] —...
Page 249: Table 121 Shutdown Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service — [no] port-state — [no] sap-id debug — igmp — router — [no] interface [ip-int-name | ip-address] — [no] [ip-int-name] — [no] misc — [no] packet [query|v1-report|v2-report|v3-report|v2-leave][ip-int-name|ip-address] 5.16 VPLS Service CLI Configuration Commands The following commands are described below: •...
Page 250: Table 122 Description Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>service>vpls configure>service>vpls>interface configure>service>vpls>mesh-sdp configure>service>vpls>mesh-sdp>eth-cfm>mep configure>service>vpls>egress>rate-limit-pbits configure>service>vpls>sap configure>service>vpls>sap>eth-cfm>mep configure>service>vpls>sap>stp configure>service>vpls>spoke-sdp configure>service>vpls>spoke-sdp>eth-cfm>mep configure>service>vpls>stp Description The shutdown command administratively disables an entity. When disabled, an entity does not change, reset, or remove any configuration settings or statistics.
Page 251: Table 123 Description Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Parameters description-string - The description character string. Allowed values are any string up to 80 characters long composed of printable, 7-bit ASCII characters. If the string contains special characters (#, $, spaces, etc.), the entire string must be enclosed within double quotes.
Page 252 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command creates or modifies a Virtual Private LAN Services (VPLS) instance. The configure service vpls command is used to create or maintain a v-VPLS service or an m-VPLS service, depending on the context specified by the operator.
Page 253: Table 125 Def-Mesh-Vc-Id Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.2 def-mesh-vc-id Table 125 def-mesh-vc-id command Item Description Syntax def-mesh-vc-id vc-id no disable-learning [vc-id] Context configure>service>vpls Description This command configures the value used by each end of a tunnel to identify the VC. If this command is not configured, then the service ID value is used as the VC-ID.
Page 254: Table 127 Disable-Learning Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.2.4 disable-learning Table 127 disable-learning command Item Description Syntax disable-learning no disable-learning Context configure>service>vpls configure>service>pw-template Description In the context of vpls: This command enables learning of new MAC addresses in the v-VPLS forwarding database (FDB) for the service instance.
Page 255: Table 129 Endpoint Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.6 endpoint Table 129 endpoint command Item Description Syntax endpoint endpoint-name [create] no endpoint Context configure>service>vpls Description This command configures a service endpoint. Parameter endpoint-name — Specifies an endpoint name, 32 chars maximum 5.16.2.7 ignore-standby-signaling Table 130...
Page 256: Table 132 Static-Mac Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters revert-time — [0..600 seconds] infinite — makes endpoint non-revertive (2 of 2) 5.16.2.9 static-mac Table 132 static-mac command Item Description Syntax static-mac ieee-address [create] no static-mac Context configure>service>vpls>endpoint...
Page 257: Table 134 Extfwd Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.11 extfwd Table 134 extfwd command Item Description Syntax extfwd Context configure>service>vpls Description This command enables the context to configure External Packet Forwarding (EPF) policies. 5.16.2.12 device-ip Table 135 device-ip command Item...
Page 258: Table 137 Interface Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters table-size — The maximum number of MAC entries in the forwarding database. Values: 1 — 131071 (2 of 2) 5.16.2.14 interface Table 137 interface command Item Description Syntax...
Page 259: Table 138 Address Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.15 address Table 138 address command Item Description Syntax address ip-address[/mask] no address Context configure>service>vpls>interface Description This command assigns an IP address, IP subnet, to a VPLS management router interface. Only one IP address can be associated with an IP interface.
Page 260: Table 140 Arp-Timeout Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.2.16 arp-timeout Table 140 arp-timeout command Item Description Syntax arp-timeout seconds no arp-timeout Context configure>service>vpls>interface Description This command configures the minimum time, in seconds, an ARP entry learned on the IP interface is stored in the ARP table.
Page 261: Table 142 Mesh-Dsp Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Parameters seconds — The aging time for local MACs expressed in seconds. Values: 60 — 86400 (2 of 2) 5.16.2.18 mesh-sdp Table 142 mesh-dsp command Item Description Syntax...
Page 262: Table 143 Spoke-Sdp Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sdp-id — The SDP identifier. Values 1 — 17407 vc-id — The virtual circuit identifier. This value is used to validate the VC ID portion of each mesh SDP binding defined in the service.
Page 263 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Description This command binds a service to an existing Service Distribution Point (SDP). A spoke SDP is treated like the equivalent of a traditional bridge “port” where flooded traffic received on the spoke SDP is replicated on all other “ports”...
Page 264: Table 144 Control-Word Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.2.20 control-word Table 144 control-word command Item Description Syntax egress Context configure>service>vpls>mesh-sdp configure>service>vpls>spoke-sdp configure>service>pw-template Description This command enables the use of the control word on pseudowire packets in VPLS and enables the use of the control word individually on each mesh-sdp or spoke-sdp.
Page 265: Table 146 Egress Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Description This command enables the use of the hash label on a VLL, or VPLS service bound to LDP SDP. When this feature is enabled, the ingress LER is modified so that the result of the hash on the ingress packet header is communicated to the egress data path for use as index to select the value of the label field of the hash label.
Page 266: Table 148 Vc-Label Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command configures the ingress SDP context. (2 of 2) 5.16.2.24 vc-label Table 148 vc-label command Item Description Syntax [no] vc-label [egress-vc-label] Context configure>service>vpls>mesh-sdp>egress configure>service>vpls>spoke-sdp>egress Description This command configures the egress VC label.
Page 267: Table 150 Force-Vlan-Vc-Forwarding Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.26 force-vlan-vc-forwarding Table 150 force-vlan-vc-forwarding command Item Description Syntax [no] force-vlan-vc-forwarding Context configure>service>vpls>mesh-sdp configure>service>vpls>spoke-sdp configure>service>pw-template Description This command forces vc-vlan-type forwarding in the data path for spoke/mesh SDPs which have either vc-type.
Page 268: Table 153 Vlan-Vc-Tag Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command specifies the precedence of the SDP binding when there are multiple SDP bindings attached to one service endpoint. The value of zero can only be assigned to one SDP bind making it the primary SDP bind.
Page 269: Table 154 Vlan-Vc-Etype Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.30 vlan-vc-etype Table 154 vlan-vc-etype command Item Description Syntax vlan-vc-etype etype no vlan-vc-etype Context configure>service>pw-template Description This command enables the configuration of an alternate TPID value to be used at the pseudo wire template level.
Page 270: Table 156 Mfib-Table-Size Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.2.32 mfib-table-size Table 156 mfib-table-size command Item Description Syntax mfib-table-size size no mfib-table-size Context configure>service>vpls Description This command specifies the maximum number of (s,g) entries in the multicast forwarding database (MFIB) for the v-VPLS instance.
Page 271: Table 158 Remote-Age Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.34 remote-age Table 158 remote-age command Item Description Syntax remote-age aging-timer no remote-age Context configure>service>vpls Description Specifies the aging time for remotely learned MAC addresses in the forwarding database (FDB) for the Virtual Private LAN Service (VPLS) instance.
Page 272: Table 160 Service-Mtu Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.2.36 service-mtu Table 160 service-mtu command Item Description Syntax service-mtu octets no service-mtu Context configure>service>vpls Description This command configures the service payload (Maximum Transmission Unit – MTU), in bytes, for the service.
Page 273: Table 162 Sgt-Qos Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.37 sgt-qos Table 162 sgt-qos command Item Description Syntax sgt-qos sgt-qos-policy [no] sgt-qos Context configure>service>vpls Description This command enables the context to configure DSCP/Dot1p re-marking for self-generated traffic.
Page 274: Table 165 Storm-Control Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command enables and disables user to user communication for a v-VPLS service. It does not apply to m-VPLS. When enabled, user to user traffic is permitted between users on distinct SAPs.
Page 275: Table 167 Bgp-Vpls Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.42 bgp-vpls Table 167 bgp-vpls command Item Description Syntax bgp-vpls Context configure>service>vpls Description This command enables the context to configure the BGP-VPLS parameters and addressing. 5.16.2.43 max-ve-id Table 168 max-ve-id command Item...
Page 276: Table 169 Ve-Name Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command configures the allowed range for the VE-id value: locally configured and received in a NLRI. Configuration of a VE-id higher than the value specified in this command is not allowed.
Page 277: Table 170 Ve-Id Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Description This command creates or edits a ve-name. Just one ve-name can be created per BGP VPLS instance. The no form of this command removes the configured ve-name from the bgp vpls node. It can only be used when the BGP VPLS status is shutdown.
Page 278: Table 172 Bgp-Ad Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command administratively enables/disables the local BGP VPLS instance. On de-activation, an MP-UNREACH-NLRI must be sent for the local NLRI. The no form of the command enales the BGP VPLS addressing and the related BGp advertisement.
Page 279: Table 174 Route-Target Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Description This command binds the advertisements received with the route target (RT) that matches the configured list (either the generic or the specified import) to a specific pw-template. If the RT list is not present, the pw-template is used for all of them.
Page 280: Table 175 Vpls-Id Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Default no ve-name Parameters export ext-community — Specifies communities allowed to be sent to remote PE neighbors. import ext-community — Specify communities allowed to be accepted from remote PE neighbors.
Page 281: Table 177 Prefix Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.52 prefix Table 177 prefix command Item Description Syntax prefix low-order-vsi-id no prefix Context configure>service>vpls>bgp-ad>vsi-id Description This command specifies the low-order 4 bytes used to compose the Virtual Switch Instance Identifier (VSI-ID) to use for NLRI in BGP auto-discovery in this VPLS service.
Page 282: Table 179 L2-Route-Table Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Values ip-addr: a.b.c.d comm-val: 0..65535 as-number: 0..65535 ext-comm-val: 0..4294967295 (2 of 2) 5.16.2.54 l2-route-table Table 179 l2-route-table command Item Description Syntax l2-route-table [detail] [bgp-ad] [bg-vpls] Context show>service show>service>id...
Page 283: Table 181 Split-Horizon-Group Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.56 split-horizon-group Table 181 split-horizon-group command Item Description Syntax [no] split-horizon-group [group-name] Context config>service>pw-template Description This command creates a new split horizon group (SHG). Auto-discovered SDP will forward the traffic between the SDPs by default. If mesh kind of behavior is required, split horizon group needs to be configured.
Page 284: Table 183 Stp Command
This command enables the context to configure the Spanning Tree Protocol (STP) parameters for the m-VPLS. Nokia’s STP is simply the Spanning Tree Protocol (STP) with a few modifications to better suit the operational characteristics of VPLS services. The most evident change is to the root bridge election.
Page 285: Table 186 Forward-Delay Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Context configure>service>vpls>sap>stp Description This command configures the SAP as an edge or non-edge port. If auto-edge is enabled for the SAP, this value will be used only as the initial value. Note: The function of the edge-port command is similar to the rapid-start command.
Page 286: Table 187 Hello-Time Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.3.5 hello-time Table 187 hello-time command Item Description Syntax hello-time hello-time no hello-time Context configure>service>vpls>stp Description This command configures the Spanning Tree Protocol (STP) hello time for the m-VPLS. The hello-time parameter defines the default timer value that controls the sending interval between BPDU configuration messages by this bridge, on ports where this bridge assumes the designated role.
Page 287: Table 189 Link-Type Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.3.7 link-type Table 189 link-type command Item Description Syntax link-type {pt-pt | shared} no link-type Context configure>service>vpls>sap>stp Description This command instructs STP on the maximum number of bridges behind this SAP. If there is only a single bridge, transitioning to forwarding state will be based on handshaking (fast transitions).
Page 288: Table 192 Mst-Port-Priority Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This commands specifies path-cost within a given instance, expressing probability that a given port will be put into the forwarding state in case a loop occurs (the highest value expresses lowest priority).
Page 289: Table 194 Mode Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Description This commands specifies the port priority within a given instance, expressing probability that a given port will be put into the forwarding state if a loop occurs. The no form of this command sets port-priority to its default value.
Page 290: Table 196 Mst-Priority Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>service>vpls>stp Description This command creates the context to configure MST instance (MSTI) related parameters. Up to 16 instances will be supported by MSTP. The instance 0 is mandatory by protocol and therefore, it cannot be created by the CLI.
Page 291: Table 198 Mst-Max-Hops Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Context configure>service>vpls>stp>mst-instance Description This command specifies a range of VLANs associated with a certain MST-instance. This range applies to all SAPs of the m-VPLS. Every VLAN range that is not assigned within any of the created mst-instance is automatically assigned to mst-instance 0.
Page 292: Table 199 Mst-Name Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.3.17 mst-name Table 199 mst-name command Item Description Syntax mst-name region-name no mst-name Context configure>service>vpls>stp Description This command defines an MST region name. Two bridges are considered as a part of the same MST region as soon as their configuration of the MST region name, the MST-revision and VLAN-to-instance assignment is identical.
Page 293: Table 202 Port-Num Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Context configure>service>vpls>sap>stp Description This command configures the Spanning Tree Protocol (STP) path cost for the SAP. The SAP path cost is used by STP to calculate the path cost to the root bridge. The path cost in BPDUs received on the root port is incremented with the configured path cost for that SAP.
Page 294: Table 204 Priority Command
Description This command configures the Nokia Spanning Tree Protocol (STP) priority for the SAP. STP priority is a configurable parameter associated with an SAP. When configuration BPDUs are received, the priority is used in some circumstances as a tie breaking mechanism to determine whether the SAP will be designated or blocked.
Page 295: Table 205 Rapid-Start Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.3.23 rapid-start Table 205 rapid-start command Item Description Syntax [no] rapid-start Context configure>service>vpls>sap>stp Description This command enables or disables a rapid start. Default no rapid-start 5.16.3.24 root-guard Table 206 root-guard command Item...
Page 296 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command creates a Service Access Point (SAP) within an m-VPLS or v-VPLS service. An SAP is a combination of port and encapsulation parameters which identifies the SAP on the interface and within the ISAM.
Page 297: Table 208 Sap Parameters
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag | *} • port-id Specifies the physical port ID in the following format: <port-id>: <nwport-id | ltport-id>...
Page 298: Table 209 Enable-Stats Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.4.2 enable-stats Table 209 enable-stats command Item Description Syntax enable-stats no enable-stats Context configure>service>vpls configure>service>vpls>sap Description This command enables statistics/PM collection for the SAP. 5.16.4.3 restricted-tagging Table 210 restricted-tagging command Item Description...
Page 299: Table 212 Eth-Cfm Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Description This command creates a local static MAC entry in the v-VPLS forwarding database (FDB) associated with the SAP. In a v-VPLS service, MAC addresses are associated with an SAP or with a Service Distribution Point (SDP).
Page 300: Table 213 Mep Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.4.6 Table 213 mep command Item Description Syntax mep mep-id domain md-index association ma-index [direction {up | down}] mep mep-id domain md-indexassociation ma-index Context configure>service>vpls>sap>eth-cfm configure>service>vpls>mesh-sdp>eth-cfm configure>service>vpls>spoke-sdp>eth-cfm configure>eth-ring>path>eth-cfm Description This command enables the Configuration of a Ethernet CFM Maintenance Endpoint...
Page 301: Table 215 Ccm-Ltm-Priority Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.4.8 ccm-ltm-priority Table 215 ccm-ltm-priority command Item Description Syntax ccm-ltm-priority priority no ccm-ltm-priority Context configure>service>vpls>sap>eth-cfm>mep configure>service>vpls>mesh-sdp>eth-cfm>mep configure>service>vpls>spoke-sdp>eth-cfm>mep configure>eth-ring>path>eth-cfm>mep Description This command enables configuration of priority for CCM and LTM messages Default Parameters priority - Priority of the CCM/LTM Message...
Page 302: Table 217 Mac-Address Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.4.10 mac-address Table 217 mac-address command Item Description Syntax mac-address mac-address no mac-address Context configure>service>vpls>sap>eth-cfm>mep configure>service>vpls>mesh-sdp>eth-cfm>mep configure>service>vpls>spoke-sdp>eth-cfm>mep configure>eth-ring>path>eth-cfm>mep Description This command enables configuration of the MAC Address for the MEP Parameters mac-address - The MAC address of the MEP in xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx format Value: xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx...
Page 303: Table 219 Y1731Pm-Enable Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.5 VPLS SAP Filter and QoS Policy Commands 5.16.5.1 y1731pm-enable Table 219 y1731pm-enable command Item Description Syntax [no] y1731pm-enable Context configure>service>vpls>sap>eth-cfm>mep Description This command enables, disables, transmit s, and receives Y1731 PM PDUs. Default no y1731pm-enable 5.16.5.2...
Page 304: Table 222 Egress Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command enables the context to configure egress SAP filter policies. If no egress filter is defined, no filtering is performed. (2 of 2) 5.16.5.4 egress Table 222...
Page 305: Table 225 Lag-Link-Map-Profile Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.5.7 lag-link-map-profile Table 225 lag-link-map-profile command Item Description Syntax no lag-link-map-profile [link-map-profile-id] Context configure>service>vpls>sap Description This command associates link-map-profile in the lag with the SAP, using the lag-link-map-profile command.
Page 306: Table 228 Qos Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command associates an IP filter policy or MAC filter policy with an ingress or egress Service Access Point (SAP) or IP interface. Filter policies control the forwarding and dropping of packets based on IP or MAC matching criteria.
Page 307: Table 229 Rate-Limit Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Parameters policy-id — The ID of the QoS policy. Values: 2 — 65535 (2 of 2) 5.16.5.11 rate-limit Table 229 rate-limit command Item Description Syntax rate-limit cir cir-rate pir pir-rate [cbs cbs-size] [pbs pbs-size] no rate-limit Context...
Page 308: Table 231 Rate-Limit-Pbits Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>service>vpls>ingress Description This command defines the aggregate ingress rate limit per VPLS service. It applies to traffic associated to the VPLS service which is ingressing on regular ports (network ports) The committed information rate and the peak information rate are entered Optionally, the committed burst size and the peak burst size may be entered.
Page 309: Table 233 Dot1P Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Context configure>service>vpls>egress>rate-limit-pbits Description This command defines the aggregate egress rate limit for the v-VPLS service matching the dot1p bits specified through rate-limit-pbits. It applies to traffic associated to the service which is egressing on regular ports (network ports).
Page 310: Table 234 Meter-Mode Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.5.16 meter-mode Table 234 meter-mode command Item Description Syntax meter-mode {trtcm | trtcm-modified} no meter-mode Context configure>service>vpls>egress>rate-limit-pbits Description This command defines the two-rate three-color marking meter's algorithm. Parameters trctm - The rate-limiting is compliant as per RFC 2698 trctm-modified - The rate-limiting is compliant as per RFC 4115...
Page 311: Table 237 Last-Member-Query-Interval Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Context configure>service>vpls>sap>igmp-snooping configure>service>mesh-sdp>igmp-snooping configure>service>spoke-sdp>igmp-snooping configure>service>pw-template>igmp-snooping Description This command enables fast leave. When IGMP fast leave processing is enabled, the ISAM will immediately remove an SAP from the IP multicast group when it detects an IGMP 'leave' on that SAP.
Page 312: Table 239 Query-Interval Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>service>vpls>sap>igmp-snooping configure>service>mesh-sdp>igmp-snooping configure>service>spoke-sdp>igmp-snooping Description This command specifies whether a multicast router is attached behind this SAP. Configuring an SAP as an mrouter-port will have a the following effect: IGMP reports generated by the system as a result of someone joining or leaving a multicast group, will be sent to this SAP.
Page 313: Table 240 Query-Response-Interval Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.6.6 query-response-interval Table 240 query-response-interval command Item Description Syntax query-response-interval seconds no query-response-interval Context configure>service>vpls>sap>igmp-snooping Description This command configures the IGMP query response interval. If the send-queries command is enabled, this parameter specifies the maximum response time advertised in IGMPv2/v3 queries.
Page 314: Table 242 Report-Src-Ip Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.6.8 report-src-ip Table 242 report-src-ip command Item Description Syntax report-src-ip ip-address no report-src-ip Context configure>service>vpls>igmp-snooping Description This parameter specifies the source IP address used when generating IGMP reports. According the IGMPv3 standard, a zero source address is allowed in sending IGMP reports.
Page 315: Table 244 Send-Queries Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.6.10 send-queries Table 244 send-queries command Item Description Syntax [no] send-queries Context configure>service>vpls>sap>igmp-snooping Description This command specifies whether to send IGMP general query messages on the SAP. When send-queries is configured, all type of queries generated ourselves are of the configured version.
Page 316: Table 246 Group Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.6.12 group Table 246 group command Item Description Syntax group grp-ip-address [no] group Context configure>service>vpls>igmp-snooping>static configure>service>vpls>sap>igmp-snooping>static configure>service>mesh-sdp>igmp-snooping>static configure>service>spoke-sdp>igmp-snooping>static Description This command adds a static multicast group either as a (*,G) or one or more (S,G) records. Use IGMP static group memberships to test multicast forwarding without a receiver host.
Page 317: Table 248 Starg Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Parameters ip-address — Specifies the IPv4 unicast address. (2 of 2) 5.16.6.14 starg Table 248 starg command Item Description Syntax [no] starg Context configure>service>vpls>igmp-snooping>static>group configure>service>vpls>sap>igmp-snooping>static>group configure>service>mesh-sdp>igmp-snooping>static>group configure>service>spoke-sdp>igmp-snooping>static>group Description...
Page 318: Table 250 Fdb-Info Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.7 Show Commands 5.16.7.1 fdb-info Table 250 fdb-info command Item Description Syntax fdb-info Context show>service Description Displays global FDB usage information. Table describes the command output fields. Table 251 Show FDB-Info Command Output Fields Label...
Page 319: Table 252 Fdb-Mac Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.7.2 fdb-mac Table 252 fdb-mac command Item Description Syntax fdb-mac ieee-address [expiry] Context show>service Description This command displays the FDB entry for a given MAC address. Parameters ieee-address - The 48-bit MAC address for which to display the FDB entry in the form aa:bb:cc:dd:ee:ff or aa-bb-cc-dd-ee-ff where aa, bb, cc, dd, ee and ff are hexadecimal numbers.
Page 320: Table 255 Show Service Sap Command Output Fields
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} • port-id Specifies the physical port ID in the following format: <port-id>: <nwport-id | ltport-id>...
Page 321: Table 256 Id Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.7.4 Table 256 id command Item Description Syntax id service-id Context show>service Description Display information for a particular service-id. Parameters service-id — The unique service identification number that identifies the service in the service domain.
Page 322: Table 259 Base Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Last Mgmt Change The date and time of the most recent management-initiated change to this customer. SAP Count The number of SAPs specified for this service. Circuit ID Specifies whether the If Index is inserted in Circuit ID suboption of Option 82.
Page 323: Table 261 Fdb Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Label Description Admin State The administrative state of the service. Oper State The operational state of the service. The largest frame size (in octets) that the service can handle. SAP Count The number of SAPs defined on the service.
Page 324: Table 262 Show Fdb Command Output Fields
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} • port-id Specifies the physical port ID in the following format: <port-id>: <nwport-id | ltport-id>...
Page 325: Table 263 Mfib Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.7.8 mfib Table 263 mfib command Item Description Syntax mfib [brief] [ip] mfib group grp-address Context show>service>id Description This command displays the multicast FIB on the v-VPLS service. Parameters brief - Displays a brief output.
Page 326: Table 266 Sap Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command displays the MSTP specific configuration data. This command is only valid on a management VPLS. (2 of 2) 5.16.7.10 Table 266 sap command Item Description Syntax...
Page 327: Table 267 Show Service-Id Sap Command Output Fields
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} • port-id Specifies the physical port ID in the following format: <port-id>: <nwport-id | ltport-id>...
Page 328: Table 268 Sap-Stats Command Output Fields
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description The SAP and qtag. Encap The encapsulation type of the SAP. Ethertype Specifies an Ethernet type II Ethertype value. Admin State The administrative state of the SAP. Oper State The operational state of the SAP.
Page 329: Table 269 Curr-15Min-Stats Command Output Fields
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Label Description Ingress Packets Number of packets that have been received on this SAP after statistics collection was enabled Ingress Octets Number of bytes that have been received on this SAP after statistics collection was enabled Egress Packets Number of packets that have been transmitted on this SAP after statistics collection...
Page 330: Table 271 Prev-15Min-Stats Command Output Fields
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Egress Octets The number of bytes transmitted on this SAP since the beginning of the current day interval elapsed-time The amount of time, measured in seconds, that has elapsed since the beginning of the current day interval Measure-time The amount of time, measured in seconds that statistics for this entry have been...
Page 331: Table 273 Stp Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Label Description Measure-time The amount of time, measured in seconds that statistics for this entry have been actually counted for the 1-day interval. This value will be the same as the interval except in a situation where performance monitoring data could not be collected for this SAP for some reason (2 of 2)
Page 332 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Root path cost Specifies the cost of the path to the root bridge as seen from this bridge. Root forward delay Specifies how fast the root changes its state when moving toward the forwarding state. Root hello time Specifies the amount of time between the transmission of configuration BPDUs.
Page 333: Table 275 Igmp-Snooping Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.8 IGMP Snooping Show Commands 5.16.8.1 igmp-snooping Table 275 igmp-snooping command Item Description Syntax igmp-snooping Context show>service>id Description This command enables the context to display IGMP snooping information. 5.16.8.2 Table 276 all command...
Page 334: Table 278 Mrouters Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Num Groups Specifies the actual number of multicast groups that can be joined on this SAP. (2 of 2) 5.16.8.3 mrouters Table 278 mrouters command Item Description Syntax...
Page 335: Table 280 Show Port-Db Command Output Fields
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} • port-id Specifies the physical port ID in the following format: <port-id>: <nwport-id | ltport-id>...
Page 336: Table 281 Querier Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Compatibility mode Specifies the IGMP mode. This is used in order for routers to be compatible with older version routers. IGMPv3 hosts must operate in Version 1 and Version 2 compatibility modes.
Page 337: Table 282 Querier Command Output Fields
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Table 282 Querier Command Output Fields Label Description SAP Id Specifies the SAP ID of the service. IP address Specifies the IP address of the querier. Expires The time left, in seconds, that the query will expire.
Page 338: Table 284 Static Command Output Fields
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} • port-id Specifies the physical port ID in the following format: <port-id>: <nwport-id | ltport-id>...
Page 339: Table 286 Statistics Command Output Fields
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Context show>service>id>igmp-snooping Description This command displays IGMP snooping statistics for the v-VPLS service. Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} •...
Page 340: Table 287 Id Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Bad Length number of IGMP messages that have been dropped because bad length Bad IP Checksum number of IGMP messages that have been dropped because bad IP checksum Bad IGMP Checksum number of IGMP messages that have been dropped because bad IGMP checksum Bad Encoding...
Page 341: Table 289 Fdb Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Description Clears DHCP statistics for this service. Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} •...
Page 342 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters all - Clears all FDB entries. mac ieee-address - Clears only FDB entries in the FDB table with the specified 48-bit MAC address. The MAC address can be expressed in the form aa:bb:cc:dd:ee:ff or aa-bb-cc-dd-ee-ff where aa, bb, cc, dd, ee and ff are hexadecimal numbers.
Page 343: Table 290 Sap Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.9.4 Table 290 sap command Item Description Syntax sap sap-id Context clear>service>statistics Description This command displays IGMP snooping statistics for the v-VPLS service. Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} •...
Page 344: Table 292 Mesh-Sdp Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.9.6 mesh-sdp Table 292 mesh-sdp command Item Description Syntax mesh-sdp sdp-id:[vc-id] {all | counters} Context clear>service>statistics>id Description This command clears all the statistics associated with the mesh SDP. Parameters sdp-id - The SDP ID for which to clear statistics.
Page 345: Table 294 Stp Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.9.8 Table 294 stp command Item Description Syntax Context clear>service>id clear>service>statistics>id Description Clears all spanning tree statistics for the service ID. 5.16.9.9 detected-protocols Table 295 detected-protocols command Item Description Syntax...
Page 346: Table 296 Statistics Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters all - Clears all detected protocol statistics. sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} •...
Page 347: Table 297 Mesh-Sdp Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Parameters all - Clears the statistics for all SAPs. sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} •...
Page 348: Table 298 Mesh-Sdp Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sdp-id - The SDP ID for which to clear the ingress VC label. Values: 1...17407 vc-id - The virtual circuit ID on the SDP ID for which to clear the ingress VC label. Values: 1...4294967295 (2 of 2) 5.16.9.12...
Page 349: Table 300 Id Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.10 Debug Commands 5.16.10.1 Table 300 id command Item Description Syntax id service-id] Context debug>service Description This command debugs commands for a specific service. Parameters service-id - The ID that uniquely identifies a service. 5.16.10.2 igmp-snooping Table 301...
Page 350: Table 303 Mac Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.10.4 Table 303 mac command Item Description Syntax [no]mac ieee-address Context debug>service>id>igmp Description This command shows IGMP packets for the specified MAC address. The no form of the command disables the MAC debugging. 5.16.10.5 mode Table 304...
Page 351: Table 306 All-Events Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.10.7 all-events Table 306 all-events command Item Description Syntax [no] all-events Context debug>service>stp Description This command enables STP debugging for all events. 5.16.10.8 bpdu Table 307 bpdu command Item Description Syntax...
Page 352: Table 309 Exception Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.10.10 exception Table 309 exception command Item Description Syntax [no] exception Context debug>service>stp Description This command enables STP debugging for exceptions. 5.16.10.11 fsm-state-changes Table 310 fsm-state-changes command Item Description Syntax...
Page 353: Table 312 Port-Role Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.10.13 port-role Table 312 port-role command Item Description Syntax [no] port-role Context debug>service>stp Description This command enables STP debugging for changes in port roles. 5.16.10.14 port-state Table 313 port-state command Item Description...
Page 354: Table 315 Interface Command
Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} • port-id Specifies the physical port ID in the following format: <port-id>: <nwport-id | ltport-id>...
Page 355: Table 316 Mcs Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.10.17 Table 316 mcs command Item Description Syntax [no] mcs [ip-int-name] Context debug>router>igmp Description This command enables debugging for IGMP MCS. Parameters ip-int-name — Only displays the information associated with the specified IP interface name. 5.16.10.18 misc Table 317...
Page 356 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 3HH-11985-AAAA-TQZZA Issue: 13...
Page 357: Internet Enhanced Service
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6 Internet Enhanced Service 6.1 In This Chapter 6.2 IES Services Overview 6.3 IES Features 6.4 Configuring an IES Service with CLI 6.5 Basic Configuration 6.6 Common Configuration Tasks 6.7 Configuring IES Components 6.8 Service Management Tasks 6.9 IES Services CLI Command Reference...
Page 358: Ies Features
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.3 IES Features 6.3.1 IP Interfaces IES customer IP interfaces can be configured with most of the same options found on the core IP interfaces. The advanced configuration options supported are: •...
Page 359: Configuring An Ies Service With Cli
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service The DHCPv4 and DHCPv6 lease state is synchronized to the standby network card. For DHCPv6, the managed neighbor cache and managed routes are also synchronized to the standby network card. If the active network card fails, all DHCP hosts stay active without service interruption.
Page 360: Common Configuration Tasks
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide exit no shutdown ---------------------------------------------- *A:ALA-48>configure>service# 6.6 Common Configuration Tasks This section provides a brief overview of the tasks that must be performed to configure IES services and provides the CLI commands. 1 Associate an IES service with a customer ID.
Page 361: Configuring Ies Interface Parameters
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.7.2 Configuring IES Interface Parameters The following example displays an IES configuration with interface parameters: A:ALA-48>configure>service>ies>interface# info ---------------------------------------------- address 10.1.1.1/24 sap nt:sfp:1:50 create ingress exit egress exit exit ---------------------------------------------- A:ALA-48>configure>service>ies>interface# 6.7.3...
Page 362: Modifying Ies Service Parameters
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.8.1 Modifying IES Service Parameters Existing IES service parameters in the CLI or NMS can be modified, added, removed, enabled or disabled. The changes are applied immediately to all services when the charges are applied.
Page 363: Re-Enabling An Ies Service
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.8.4 Re-enabling an IES Service To re-enable an IES service that was shut down: configure>service> ies service-id [no] shutdown Example: configure>service# ies 2000 configure>service>ies# no shutdown configure>service>ies# exit 6.9 IES Services CLI Command Reference 6.9.1 Command Hierarchies...
Page 364 Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide — no arp-timeout — transmit-interval [receive receive-interval] [multiplier multiplier] — — delayed-enable [seconds] — no delayed-enable — description description-string — no description — dhcp — description description-string — no description —...
Page 365: Interface Sap Commands
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.9.1.3 Interface SAP Commands configure — service — service-id [customer customer-id] — [no] interface ip-int-name — [no] sap-id — description description-string — no description — egress — filter {ip ip-filter-id | ipv6 ipv6-filter-id} —...
Page 366: Table 319 Shutdown Command
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10 IES Service CLI Configuration Commands The following commands are described: • Generic Commands • IES Global Commands • IES QoS Policy Commands • IES Interface Commands • IES Interface DHCP Commands •...
Page 367: Table 320 Description Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Special Cases IES — The default administrative status of an IES service is down. While the service is down, all its associated virtual router interfaces will be operationally down. The administrative state of the service is not reflected in the administrative state of the virtual router interface.
Page 368: Table 322 Sgt-Qos Command
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>service>ies configure>service>ies>interface Description This command creates a text description stored in the configuration file for a configuration context. The description command associates a text string with a configuration context to help identify the content in the configuration file.
Page 369: Table 324 Egress Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Context configure>service Description This command creates or edits an IES service instance. The ies command is used to create or maintain an Internet Enhanced Service (IES). If the service-id does not exist, a context for the service is created.
Page 370: Table 325 Ingress Command
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>service>ies Description This command enables the context to configure egress rate-limiting policies. If no egress filter is defined, no rate-limiting is performed. (2 of 2) 6.10.3.2 ingress Table 325...
Page 371: Table 327 Rate-Limit Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.10.3.4 rate-limit Table 327 rate-limit command Item Description Syntax rate-limit cir cir-rate pir pir-rate [cbs cbs-size] [pbs pbs-size] no rate-limit Context configure>service>ies>egress Description This command defines the aggregate egress rate limit per IES service. It applies to traffic associated to the IES service which is egressing on regular ports (network ports) The committed information rate and the peak information rate are entered...
Page 372: Table 329 Interface Command
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters cir cir-rate — The committed information rate expressed in kbps. Values: up to 100 Gbps pir pir-rate — The peak information rate expressed in kbps. Values: up to 100 Gbps cbs cbs-size —...
Page 373: Table 330 Address Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Description This command creates a logical IP routing interface for an Internet Enhanced Service (IES). Once created, attributes like an IP address and service access point (SAP) can be associated with the IP interface.
Page 374: Table 331 Operational State
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command assigns an IP address, IP subnet, and broadcast address format to an IES IP router interface. Only one IP address can be associated with an IP interface. An IP address must be assigned to each IES IP interface.
Page 375: Table 332 Arp-Timeout Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.10.4.3 arp-timeout Table 332 arp-timeout command Item Description Syntax arp-timeout seconds no arp-timeout Context configure>service>ies>interface Description This command configures the minimum time, in seconds, an ARP entry learned on the IP interface is stored in the ARP table.
Page 376: Table 334 Delayed-Enable Command
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters transmit-interval - Sets the transmit interval, in milliseconds, for the BFD session. Values 100 — 100000 Default: 100 receive receive-interval - Sets the receive interval, in milliseconds, for the BFD session. Values 100 —...
Page 377: Table 336 Local-Proxy-Arp Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Description This command configures the IP maximum transmit unit (packet) for the interface. If the configured value is less than or equal to 9194, it applies to both the control plane and the data plan (fast path).
Page 378: Table 338 Protect Command
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.4.9 protected Table 338 protect command Item Description Syntax [no] protected Context configure>service>ies>interface Description This command selects the IES interface configuration and the associated configuration for the interface that enables the interface to be operational (manage access from remote clients). The command stores the configuration as part of protected configuration when the user issues the admin software-management IHub database oam-save-protected command.
Page 379 FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Parameters ip-address — The IP address of the IP interface. The ip-address portion of the address command specifies the IP host address that will be used by the IP interface within the subnet. This address must be unique within the subnet and specified in dotted decimal notation.
Page 380: Table 340 Dhcp Command
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.5 IES Interface DHCP Commands 6.10.5.1 dhcp Table 340 dhcp command Item Description Syntax dhcp Context configure>service>ies>interface Description This command enables the context to configure DHCP parameters. 6.10.5.2 gi-address Table 341 gi-address command...
Page 381: Table 342 Lease-Query Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.10.5.3 lease-query Table 342 lease-query command Item Description Syntax lease-query {enable | disable}] no lease-query Context configure>service>ies>interface>dhcp Description Enables lease-query functionality in this interface. Enable will process broadcast LQ and Disable will discard broadcast LQ, but irrespective of Enable/Disable, unicast LQ will be forwarded.
Page 382: Table 345 Server Command
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>service>ies>interface>dhcp>option Description This command configures the Relay Agent Information Option (Option 82) processing. The no form of this command returns the system to the default value. Default The default is to keep the existing information intact.
Page 383: Table 347 Rid-Check-Disable Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Description This command enables dynamic host lease state management for IES IP interfaces. Lease state information is extracted from snooped or relayed DHCP ACK messages to populate lease state table entries for the IP interface.
Page 384: Table 349 Mask-Reply Command
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>service>ies>interface Description This command enables the context to configure Internet Control Message Protocol (ICMP) parameters on an IES service (2 of 2) 6.10.6.2 mask-reply Table 349 mask-reply command Item Description...
Page 385: Table 351 Unreachables Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Parameters number — The maximum number of ICMP TTL expired messages to send, expressed as a decimal integer. This parameter must be specified with the seconds parameter. Values: 10 —...
Page 386: Table 352 Ipv6 Command
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.7 IPv6 Commands 6.10.7.1 ipv6 Table 352 ipv6 command Item Description Syntax [no] ipv6 Context configure>service>ies>interface Description This command configures an IPv6 interface. When IPv6 routing is configured on the IHub and an Note —...
Page 387: Table 354 Dhcp6-Relay Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Parameters ipv6-address/prefix-length — Specifies the IPv6 address on the interface. Values: ipv6-address/prefix: ipv6-address x:x:x:x:x:x:x:x (eight 16-bit pieces) x:x:x:x:x:x:d.d.d.d x [0 — FFFF]H d [0 — 255]D prefix-length 1 —...
Page 388: Table 356 Lease-Populate Command
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.7.5 lease-populate Table 356 lease-populate command Item Description Syntax lease-populate [nbr-of-leases] no lease-populate Context configure>service>ies>interface>ipv6>dhcp6-relay Description This command specifies specify the maximum number of leases maintained in the lease state database.
Page 389: Table 358 Interface-Id Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.10.7.7 interface-id Table 358 interface-id command Item Description Syntax interface-id [ascii-tuple | ifindex | sap-id | string <string>] no interface-id Context configure>service>ies>interface>ipv6>dhcp6-relay>option Description The operator can configure the interface ID option. When the interface ID option is enabled all the relay-forward messages will include interface-id option.
Page 390: Table 360 Server Command
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.7.9 server Table 360 server command Item Description Syntax server ipv6-address [ipv6-address...(up to 8 maximum)] Context configure>service>ies>interface>ipv6>dhcp6-relay Description This command specifies a list of servers where requests will be forwarded. The list of servers can be entered as IP addresses.
Page 391: Table 363 Packet-Too-Big Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.10.7.12 packet-too-big Table 363 packet-too-big command Item Description Syntax packet-too-big [number seconds] no packet-too-big Context configure>service>ies>interface>ipv6>icmp6 Description This command configures the rate for ICMP packet-too-big messages issued on the router interface.
Page 392: Table 365 Time-Exceeded Command
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters number — The maximum number of ICMP param-problem messages to send. This parameter must be specified with the seconds parameter. Values: 10 — 1000 seconds — The time frame in seconds used to limit the number of ICMP param-problem messages that can be issued.
Page 393: Table 367 Local-Proxy-Nd Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Description This command configures the rate for ICMP host and network destination unreachable messages issued on the router interface. The unreachables command enables the generation of ICMP destination unreachables on the router interface.
Page 394: Table 368 Prefix-Stability Command
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.7.17 prefix-stability Table 368 prefix-stability command Item Description Syntax prefix-stability {enable | disable} no prefix-stability Context configure>service>ies>interface>dhcp6-relay Description Enables prefix-stability functionality in this interface. Default The default value is Disabled. Parameters {Enable} —...
Page 395: Table 370 Sap Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.10.8 IES SAP Filter and QoS Policy Commands 6.10.8.1 Table 370 sap command Item Description Syntax sap sap-id no sap sap-id Context configure>service>ies>interface Description This command creates a Service Access Point (SAP) within a service. A SAP is a combination of port and encapsulation parameters which identifies the service access point on the interface and within the ISAM.
Page 396: Table 371 Port And Encapsulation Type Values
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} • port-id Specifies the physical port ID in the following format: <port-id>...
Page 397: Table 372 Filter Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.10.8.2 filter Table 372 filter command Item Description Syntax filter { ip ip-filter-id| ipv6 ipv6-filter-id} no filter [ip ip-filter-id] [ipv6 ipv6-filter-id] Context configure>service>ies>interface>sap>egress configure>service>ies>interface>sap>ingress Description This command associates a filter policy with an ingress or egress Service Access Point (SAP). Filter policies control the forwarding and dropping of packets based on the matching criteria.
Page 398: Table 374 Ingress Command
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.8.4 ingress Table 374 ingress command Item Description Syntax ingress Context configure>service>ies>interface>sap Description This command enables the context to configure ingress SAP filter policies. If no ingress filter is defined, no filtering is performed 6.10.9 Show Commands 6.10.9.1...
Page 399: Table 377 Sap-Using Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Label Description Specifies the SAP assigned to the service. (2 of 2) 6.10.9.2 sap-using Table 377 sap-using command Item Description Syntax sap-using [sap sap-id] sap-using interface [ip-address | ip-int-name] Context show>service Description...
Page 400: Table 378 Show Service Arp Output
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: [port-id | lag-id] vlanid | no-tag • port-id Specifies the physical port ID in the following format: <port-id>...
Page 401: Table 379 Id Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.10.9.3 Table 379 id command Item Description Syntax id service-id {all | arp | base | interface | sap} Context show>service Description Display information for a particular service ID. Parameters service-id —...
Page 402 Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description SAP Count The number of SAPs specified for this service. QoS Rate-Limit Pbits The set of 802.1p bits for which the rate-limiter will be applied Committed rate (kbps) The committed rate in kbps Committed burst size (kB) The committed burst size in kb...
Page 403: Table 382 Arp Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Label Description Low priority offered The packets or octets count of the low priority traffic. Low priority dropped The number of low priority traffic packets/octets dropped. In profile forwarded The number of in-profile packets or octets (rate below CIR) forwarded.
Page 404: Table 383 Show Service Sap Output
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters ip-address — Displays only ARP entries in the ARP table with the specified IP address. Default: All IP addresses. mac ieee-address — Displays only ARP entries in the ARP table with the specified 48-bit MAC address.
Page 405: Table 384 Base Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Label Description Expiry The age of the ARP entry. Interface The interface applied to the service. The SAP ID. (2 of 2) 6.10.9.6 base Table 384 base command Item Description Syntax...
Page 406: Table 387 Lease-State Command
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: [port-id | lag-id] vlanid | no-tag • port-id Specifies the physical port ID in the following format: <port-id>...
Page 407 FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: [port-id | lag-id] vlanid | no-tag • port-id Specifies the physical port ID in the following format: <port-id>...
Page 408: Table 388 Summary Command
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.9.10 summary Table 388 summary command Item Description Syntax summary Context show>service>id>dhcp Description Displays DHCP configuration summary information. Table describes the command output fields. Table 389 Show DHCP Summary Output Label Description Interface Name...
Page 409: Table 391 Summary Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.10.9.12 summary Table 391 summary command Item Description Syntax summary Context show>service>id>dhcp6 Description Displays DHCP6 configuration summary information. Table describes the command output fields. Table 392 Show DHCP6 Summary Output Label Description Interface Name...
Page 410: Table 394 Show Dhcp Lease State Output
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters interface interface-name - Displays DHCP lease state related information for the specified interface. ipv6-address ipv6-prefix[/prefix-length] - Displays DHCP lease state related information for the specified IPv6 address. mac ieee-address - Displays DHCP lease state related information for the specified MAC address.
Page 411: Table 396 Statistics Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Label Description ServerLeaseRenew Time stamp indicates when client last renewed to the server ServerLeaseEnd Time stamp indicates when lease expires (2 of 2) 6.10.9.14 statistics Table 396 statistics command Item Description Syntax...
Page 412: Table 399 Show Service Id Interface Output
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters ip-address — The IP address of the interface for which to display information. Values: ipv4-address: a.b.c.d (host bits must be 0) ip-int-name — Specifies the IP interface name for which to display information. Values: 32 characters maximum family —...
Page 413: Table 400 Sap Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Label Description DHCP Details Description Provides the description of the IES interface. Admin state Specifies the administrative state for DHCP relay. Lease Query Specifies whether the Lease Query is enabled or disabled. Servers Specifies the configured DHCP servers.
Page 414: Table 401 Show Service Sap Output
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: [port-id | lag-id] vlanid | no-tag • port-id Specifies the physical port ID in the following format: <port-id>...
Page 415 FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Label Description Flags Specifies the conditions that affect the operating status of this SAP. Display output includes: ServiceAdminDown, SapAdminDown, InterfaceAdminDown, PortOperDown, PortMTUTooSmall, L2OperDown, SapIngressQoSMismatch, SapEgressQoSMismatch, RelearnLimitExceeded, RxProtSrcMac, ParentIfAdminDown, NoSapIpipeCeIpAddr, TodResourceUnavail, TodMssResourceUnavail, SapParamMismatch, CemSapNoEcidOrMacAddr, StandByForMcRing, ServiceMTUTooSmall, SapIngressNamedPoolMismatch, SapEgressNamedPoolMismatch, NoSapEpipeRingNode, mcStandby (22),...
Page 416: Table 402 Id Command
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.10 Clear Commands 6.10.10.1 Table 402 id command Item Description Syntax id service-id Context clear>service clear>service>statistics Description This command clears parameters for a specific service. Parameters service-id — The ID that uniquely identifies the service to clear. 6.10.10.2 interface Table 403...
Page 417: Table 405 Stp Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Description This command clears FDB entries for the service. Parameters all — Clears all FDB entries. mac ieee-address — Clears only FDB entries in the FDB table with the specified 48-bit MAC address.
Page 418: Table 406 Statistics Command
Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.10.5 statistics Table 406 statistics command Item Description Syntax statistics [sap sap-id | interface ip-address | ip-int-name] Context clear>service>id>dhcp Description This command clears DHCP statistics. Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: [port-id | lag-id] vlanid | no-tag * •...
Page 419: Table 407 Lease-State Command
FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.10.10.6 lease-state Table 407 lease-state command Item Description Syntax lease-state ipv6-address ipv6-prefix[/prefix-length] lease-state mac ieee-address lease-state sap sap-id Context clear>service>dhcp6 Description Clears lease state statistics for DHCP6. Parameters ip-prefix/prefix-length - The destination address of the aggregate route.
Page 420 Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 3HH-11985-AAAA-TQZZA Issue: 13...
Page 421: Virtual Private Routed Network Service
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7 Virtual Private Routed Network Service 7.1 In This Chapter 7.2 VPRN Service Overview 7.3 VPRN Features 7.4 Configuring a VPRN Service with CLI 7.5 Basic Configuration 7.6 Common Configuration Tasks 7.7 Configuring VPRN Components 7.8 Service Management Tasks...
Page 422: Figure 33 Virtual Private Routed Network
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide The ISAM uses an IGP (RIP, OSPF, ISIS) to exchange the routes of a particular CE router with the PE routers that are attached to that ISAM. This is done in a way which ensures that routes from different VPNs remain distinct and separate, even if two VPNs have an overlapping address space.
Page 423: Route Redistribution
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.2.1.1 Route Redistribution Routing information learned from the ISAM-to-PE routing protocols and configured static routes should be injected in the associated local VPN routing/forwarding (VRF). In the case of dynamic routing protocols, there may be protocol specific route policies that modify or reject certain routes before they are injected into the local VRF.
Page 424: Figure 34 Conceptual Diagram
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Figure 34 Conceptual Diagram IPD L3 VPRN VLANs must have system global scope IPD L2 v-VPLS v-VPLS For the MTU size of an IP interface, a fixed value of Note 1 —...
Page 425: Basic Configuration
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Topics in this section include: • Basic Configuration • Common Configuration Tasks • Configuring VPRN Components • Creating a VPRN Service • Configuring Global VPRN Parameters •...
Page 426: Common Configuration Tasks
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide exit vrrp 1 exit exit static-route 6.5.0.0/24 next-hop 10.1.1.2 router-id 10.0.0.1 group "to-cel" export "vprnBgpExpPolCust1" peer-as 65101 neighbor 10.1.1.2 exit exit exit static exit bsr-candidate shutdown exit shutdown exit...
Page 427: Configuring Vprn Components
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7 Define BGP parameters (optional). • BGP must be enabled in the configure>router>bgp context. 8 Define RIP parameters (optional). • RIP must be enabled in the configure>router>rip context. 9 Enable the service.
Page 428: Configuring Router Interfaces
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide vprn 1 customer 1 create vrf-import "vrfImpPolCust1" vrf-export "vrfExpPolCust1" autonomous-system 10000 route-distinguisher 10001:1 exit no shutdown exit ---------------------------------------------- *A:ALA-1>configure>service# 7.7.3 Configuring Router Interfaces Refer to the FD 100/320Gbps NT and FX NT IHub Router Configuration and Protocols Guide for command descriptions and syntax information to configure router interfaces.
Page 429 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service In order to enable a VPRN BGP instance, the BGP protocol must be enabled in the configure>router>bgp context on each participating ISAM router. Careful planning is essential to implement commands Note —...
Page 430: Configuring Vprn Bgp Group And Neighbor Parameters
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.7.4.1 Configuring VPRN BGP Group and Neighbor Parameters A group is a collection of related VPRN BGP peers. The group name should be a descriptive name for the group. Follow your group, name, and ID naming conventions for consistency and to help when troubleshooting faults.
Page 431: Vprn Rip Cli Syntax
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service In order to enable a VPRN RIP instance, the RIP protocol must be enabled in the configure>router> rip context on each participating ISAM. VPRN RIP is administratively enabled upon creation.
Page 432: Configuring Vprn Protocols - Ospf
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide ecmp 2 autonomous-system 10000 route-distinguisher 10001:1 vrf-target target:10001:1 interface "to-ce1" create address 11.1.0.1/24 sap nt:sfp:1:1 create ingress scheduler-policy "SLA2" qos 100 exit egress scheduler-policy "SLA1" qos 1010 filter ip 6 exit exit...
Page 433: Vprn Ospf Cli Syntax
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.7.6.1 VPRN OSPF CLI Syntax Refer to “OSPF Configuration Commands” for CLI syntax to configure VPRN parameters. The following example displays the VPRN OSPF configuration shown above: A:debby-sim1>configure>service# info ---------------------------------------------- vprn 2 customer 1 create...
Page 434: Configuring A Vprn Interface - Sap
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide static-route 6.5.0.0/24 next-hop 10.1.1.2 no shutdown exit ---------------------------------------------- *A:ALA-1>configure>service# 7.7.8 Configuring a VPRN Interface - SAP To associate an IP interface to one or more network ports and/or access/hybrid ports, at least two v-VPLS must be configured, one with a SAP on each associated network/hybrid port, and one with the access/hybrid ports.
Page 435: Deleting A Vprn Service
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service maximum-routes 2000 autonomous-system 10000 route-distinguisher 10001:1 interface "to-ce1" create address 10.1.1.1/24 sap nt:sfp:1:1 create exit exit static-route 6.5.0.0/24 next-hop 10.1.1.2 router-id 10.0.0.1 group "to-ce1" export "vprnBgpExpPolCust1" peer-as 65101 neighbor 10.1.1.2 exit...
Page 436: Re-Enabling A Vprn Service
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide configure>service# vprn 1 configure>service>vprn# shutdown configure>service>vprn# exit *A:ALA-1>configure>service# info ---------------------------------------------- vprn 1 customer 1 create shutdown vrf-import "vrfImpPolCust1" vrf-export "vrfExpPolCust1" ecmp 2 autonomous-system 10000 route-distinguisher 10001:1 auto-bind ldp vrf-target target:10001:1 interface "to-ce1"...
Page 437: Vprn Services Cli Command Reference
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service configure>service# vprn service-id [customer customer-id] no shutdown 7.9 VPRN Services CLI Command Reference 7.9.1 Command Hierarchies This section shows the following command hierarchies: • VPRN Service Configuration Commands •...
Page 438: Interface Commands
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide — [no] on-link — [no] preferred-lifetime {seconds | infinite} — [no] valid-lifetime {seconds | infinite} — [no] reachable-time milli-seconds — [no] retransmit-time milli- seconds — [no] router-lifetime seconds —...
Page 439: Interface Sap Commands
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service — prefix-stability {enable | disable} — no prefix-stability — prfx-hlddwn-time <seconds> — no prfx-hlddwn-time — server ipv6-address [ipv6-address...(up to 8 maximum)] — no server [ipv6-address...(up to 8 maximum)] —...
Page 440 Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide — service — vprn service-id [customer customer-id] — [no] — [no] advertise-inactive — [no] aggregator-id-zero — always-compare-med {zero | infinity} — no always-compare-med — [no] as-path-ignore —...
Page 441 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service — no family — hold-time seconds — no hold-time — import policy-name [policy-name...(up to 5 max)] — no import — keepalive seconds — no keepalive — local-address ip-address —...
Page 442: Ospf Configuration Commands
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide — min-route-advertisement seconds — no min-route-advertisement — multihop ttl-value — no multihop — [no] next-hop-self — [no] passive — peer-as as-number — no peer-as — preference preference —...
Page 443: Rip Configuration Commands
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service — [no] asbr — [no] compatible-rfc1583 — export policy-name [ policy-name...(up to 5 max)] — no export — external-db-overflow limit seconds — no external-db-overflow — external-preference preference —...
Page 444: Show Commands
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide — timers update timeout flush — no timers — [no] neighbor ip-int-name — authentication-key [authentication-key | hash-key] [hash2] — no authentication-key — authentication-type {none | password | message-digest} —...
Page 445: Clear Commands
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service — summary — lease-state [detail] — lease-state [detail] interface interface-name — lease-state [detail] ipv6-address ipv6-prefix[/prefix-length] — lease-state [detail] mac ieee-address — statistics [interface interface-name] — endpoint —...
Page 446: Vprn Service Cli Configuration Commands
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide — flap-statistics [[ip-prefix/mask] [neighbor ip-address]] | [group group-name] | [regex reg-exp] | [policy policy-name] — neighbor {ip-address | as as-number | external | all} [soft | soft-inbound] —...
Page 447: Table 408 Shutdown Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.1 Generic Commands 7.10.1.1 shutdown Table 408 shutdown command Item Description Syntax [no] shutdown Context configure>service>vprn configure>service>vprn configure>service>vprn>interface configure>service>vprn>interface>dhcp configure>service>vprn>interface>ipv6>dhcp6-relay configure>service>vprn>interface>sap configure>service>vprn>bgp configure>service>vprn>bgp>group configure>service>vprn>bgp>group>neighbor configure>service>vprn>ospf configure>service>vprn>ospf>area>interface configure>service>vprn>rip configure>service>vprn>rip>group configure>service>vprn>rip>group>neighbor...
Page 448: Table 409 Description Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.1.2 description Table 409 description command Item Description Syntax description description-string no description Context configure>service>vprn>interface>dhcp configure>service>vprn>bgp configure>service>vprn>rip configure>service>vprn>interface>dhcp configure>service>vprn>interface>ipv6>dhcp6-relay configure>service>vprn>interface>sap configure>service>vprn>interface>dhcp configure>service>vprn>bgp configure>service>vprn>bgp>group configure>service>vprn>bgp>group>neighbor configure>service>vprn>rip configure>service>vprn>rip>group configure>service>vprn>rip>group>neighbor Description This command creates a text description stored in the configuration file for a configuration...
Page 449: Table 411 Vprn Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Parameters description-string — The description character string. Allowed values are any string up to 160 characters long composed of printable, 7-bit ASCII characters. If the string contains special characters (#, $, spaces, etc.), the entire string must be enclosed within double quotes.
Page 450: Table 412 Aggregate Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters service-id — The unique service identification number identifying the service in the service domain. This ID must be unique to this service and may not be used for any other service of any type.
Page 451: Table 413 Autonomous-System Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Parameters summary-only — This optional parameter suppresses advertisement of more specific component routes for the aggregate. as-set — This optional parameter is only applicable to BGP and creates an aggregate where the path advertised for this route will be an AS_SET consisting of all elements contained in all paths that are being summarized.
Page 452: Table 414 Ecmp Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.2.4 ecmp Table 414 ecmp command Item Description Syntax ecmp max-ecmp-routes no ecmp Context configure>service>vprn Description This command enables equal-cost multipath (ECMP) and configures the number of routes for path sharing.
Page 453: Table 416 Maximum-Routes Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Description This command specifies the maximum number of IPv6 routes that can be held within a VPN routing/forwarding (VRF) context. Note that the VPRN service ID must be in a shutdown state in order to modify maximum-routes to lower than the existing routes in the route table.
Page 454: Table 417 Router-Advertisement Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command specifies the maximum number of remote routes that can be held within a VPN routing/ forwarding (VRF) context. Note that local, host, static and aggregate routes are not counted.
Page 455: Table 418 Interface Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.2.8 interface Table 418 interface command Item Description Syntax [no] interface ip-int-name Context configure>service>vprn>router-advertisement Description This command configures router advertisement properties on a specific interface. The interface must already exist in the configure>router>interface context.
Page 456: Table 421 Max-Advertisement-Interval Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command sets the managed address configuration flag. This flag indicates that DHCPv6 is available for address configuration in addition to any address autoconfigured using stateless address autoconfiguration.
Page 457: Table 423 Mtu Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.2.13 Table 423 mtu command Item Description Syntax mtu mtu-bytes no mtu Context configure>service>vprn>router-advertisement>interface Description This command configures the MTU for the nodes to use to send packets on the link. Default no mtu —...
Page 458: Table 426 Autonomous Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameter ip-prefix — The IP prefix for prefix list entry in dotted decimal notation. Values: ipv4-prefix a.b.c.d (host bits must be 0) ipv4-prefix-length 0 — 32 ipv6-prefix x:x:x:x:x:x:x:x (eight 16-bit pieces) x:x:x:x:x:x:d.d.d.d...
Page 459: Table 428 Preferred-Lifetime Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.2.18 preferred-lifetime Table 428 preferred-lifetime command Item Description Syntax [no] preferred-lifetime {seconds | infinite} Context configure>service>vprn>router-advertisement>interface>prefix Description This command configures the remaining length of time in seconds that this prefix will continue to be preferred, such as, time until deprecation.
Page 460: Table 430 Reachable-Time Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.2.20 reachable-time Table 430 reachable-time command Item Description Syntax [no] reachable-time milli-seconds Context configure>service>vprn>router-advertisement>interface Description This command configures how long this router should be considered reachable by other nodes on the link after receiving a reachability confirmation.
Page 461: Table 433 Route-Distinguisher Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Parameter seconds — The length of time, in seconds, (relative to the time the packet is sent) that the prefix is valid for route determination. Values: 0, 4 —...
Page 462: Table 435 Sgt-Qos Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command sets the router ID for a specific VPRN context. If neither the router ID nor the system interface are defined, the router ID from the base router context is inherited.
Page 463: Table 437 Rate-Limit Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Description The ingress QoS policy defines the match criteria used to determine what Forwarding Class (FC) each packet is associated to. Associating a QoS policy to a VPRN service effectively associates the QoS policy to all SAPs of a VPRN service at one time.
Page 464: Table 438 Rate-Limit Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters cir cir-rate — The committed information rate expressed in kbps. Values: up to 100 Gbps pir pir-rate — The peak information rate expressed in kbps. Values: up to 100 Gbps cbs cbs-size —...
Page 465: Table 439 Static-Route Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.2.29 static-route Table 439 static-route command Item Description Syntax [no] static-route {ip-prefix/mask | ip-prefix netmask} [preference preference] [metric metric] [tag tag] [enable | disable] next-hop {ip-int-name | ip-address} [bfd-enable] [no] static-route {ip-prefix/mask | ip-prefix netmask}[preference preference] [metric metric] [tag tag] [enable | disable] black-hole Context...
Page 466 Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters ip-prefix/prefix-length - The destination address of the static route. Values: ipv4-prefix a.b.c.d (host bits must be 0) ipv4-prefix-length 0 — 32 ipv6-prefix x:x:x:x:x:x:x:x (eight 16-bit pieces) x:x:x:x:x:x:d.d.d.d x: [0 —...
Page 467: Table 440 Route Preference Defaults By Route Type
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Parameters next-hop ip-address - Specifies the directly connected next hop IP address used to reach the continued destination. The next-hop keyword and the black-hole keyword are mutually exclusive. If an identical command is entered (with the exception of black-hole parameters), then this static route will be replaced with the newly entered command, and unless specified, the respective defaults for preference and metric will be applied.
Page 468: Table 441 Tiebreaker Order Of Route Types
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Route Type Preference Configurable ROUTE_PREF_BLACKHOLE_AGGR (2 of 2) Table 441 Tiebreaker Order of Route Types Tiebreaker Order Route Type Local Static OSPF IS-IS Aggregate 7.10.3 Interface Commands 7.10.3.1 interface Table 442...
Page 469: Address
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Description This command creates a logical IP routing interface for an Virtual Private Routed Network (VPRN). Once created, attributes like an IP address and service access point (SAP) can be associated with the IP interface.
Page 470: Table 443 Address Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Table 443 address command Item Description Syntax address ip-address[/mask] no address Context configure>service>vprn>interface Description This command assigns an IP address, IP subnet, and broadcast address format to an VPRN IP router interface.
Page 471: Table 444 Operational State
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Table 444 Operational State Address Administrative State Operational State No address dowm No address dowm dowm 1.1.1.1 1.1.1.1 dowm dowm 7.10.3.3 arp-timeout Table 445 arp-timeout command Item Description Syntax...
Page 472: Table 446 Bfd Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Table 446 bfd command Item Description Syntax bfd transmit-interval [receive receive-interval] [multiplier multiplier no bfd Context configure>service>vprn>interface Description This command specifies the bidirectional forwarding detection (BFD) parameters for the associated IP interface.
Page 473: Table 448 Ip-Mtu Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.3.6 ip-mtu Table 448 ip-mtu command Item Description Syntax ip-mtu octets no ip-mtu Context configure>service>vprn>interface Description This command configures the IP maximum transmit unit (packet) for the interface. If the configured value is less than or equal to 2026, it applies to both the control plane and the data plan (fast path).
Page 474: Table 450 Loopback Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Table 450 loopback command Item Description Syntax [no] loopback Context configure>service>vprn>interface Description This command specifies that the associated interface is a loopback interface that has no associated physical interface.
Page 475: Table 453 Secondary Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Description This command enables remote proxy ARP on the interface. Remote proxy ARP is similar to proxy ARP. It allows the router to answer an ARP request on an interface for a subnet that is not provisioned on that interface.
Page 476 Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters ip-address — The IP address of the IP interface. The ip-address portion of the address command specifies the IP host address that will be used by the IP interface within the subnet. This address must be unique within the subnet and specified in dotted decimal notation.
Page 477: Table 454 Dhcp Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.4 VPRN Interface DHCP Commands 7.10.4.1 dhcp Table 454 dhcp command Item Description Syntax dhcp Context configure>service>vprn>interface Description This command enables the context to configure DHCP parameters. 7.10.4.2 gi-address Table 455...
Page 478: Table 456 Option Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.4.3 option Table 456 option command Item Description Syntax no option Context configure>service>vprn>interface>dhcp Description This command enables DHCP Option 82 (Relay Agent Information Option) parameters processing and enters the context for configuring Option 82 sub-options. The no form of this command returns the system to the default.
Page 479: Table 459 Lease-Populate Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Context configure>service>vprn>interface>dhcp Description This command specifies a list of servers where requests will be forwarded. The list of servers can be entered as either IP addresses or fully qualified domain names. There must be at least one server specified for DHCP relay to work.
Page 480: Table 461 Icmp Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>service>vprn>if>dhcp Description This command disables the remote ID check in the interface. Local proxy ARP should be enabled in the respective interface. Default Remote ID check is enabled (no rid-check-disable) Parameters None...
Page 481: Table 463 Ttl-Expired Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.5.3 ttl-expired Table 463 ttl-expired command Item Description Syntax ttl-expired [number seconds] no ttl-expired Context configure>service>vprn>interface>icmp Description This command configures the rate Internet Control Message Protocol (ICMP) TTL expired messages are issued by the IP interface.
Page 482: Table 465 Ipv6 Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters number — The maximum number of ICMP unreachable messages to send. This parameter must be specified with the seconds parameter. Values: 10 — 1000 seconds —...
Page 483: Table 466 Address Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.6.2 address (ipv6) Table 466 address command Item Description Syntax address ipv6-address/prefix-length [eui-64] no address ipv6-address/prefix-length Context configure>service>vprn>interface>ipv6 Description This command assigns an IPv6 address to the VPRN interface. Up to 254 global IPv6 addresses can be configured.
Page 484: Table 469 Option Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>service>vprn>interface>ipv6>dhcp6-relay Description This command specifies specify the maximum number of leases maintained in the lease state database. Lease populate is enabled by default. The operator can change the size of lease table using this command.
Page 485: Table 471 Remote-Id Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Description The operator can configure the interface ID option. When the interface ID option is enabled all the relay-forward messages will include interface-id option. The DHCPv6 server copies this option to the relay-reply message.
Page 486: Table 473 Prfx-Hlddwn-Time Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters enable — Enables the prefix stability feature at the interface leveol. disable — Disables the prefix stability feature at the interface level. Note: Prefix-stability must be enabled before any device movement happens for IPv6 prefixes to be maintained.
Page 487: Table 475 Source-Address Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.6.11 source-address Table 475 source-address command Item Description Syntax source-address ipv6-address no source-address Context configure>service>vprn>interface>ipv6>dhcp6-relay Description This commandspecifies a source IPv6 address which will bthe e used as source IPv6 address in all the relayed DHCPv6 messages.
Page 488: Table 478 Param-Problem Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command configures the rate for ICMP packet-too-big messages issued on the router interface. By default, generation of ICMP packet-too-big messages is enabled at a maximum rate of 100 per 10 second time interval.
Page 489: Table 479 Time-Exceeded Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.6.15 time-exceeded Table 479 time-exceeded command Item Description Syntax time-exceeded [number seconds] no time-exceeded Context configure>service>vprn>interface>ipv6>icmp6 Description This command configures the rate for ICMP time-exceeded messages issued on the router interface.
Page 490: Table 481 Local-Proxy-Nd Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters number — The maximum number of ICMP unreachable messages to send. This parameter must be specified with the seconds parameter. Values: 10 — 1000 seconds —...
Page 491 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Description This command creates a Service Access Point (SAP) within a service. A SAP is a combination of port and encapsulation parameters which identifies the service access point on the interface and within the ISAM.
Page 492: Table 483 Egress Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.8 SAP Filter and QoS Policy Commands 7.10.8.1 egress Table 483 egress command Item Description Syntax egress Context configure>service>vprn>interface>sap Description This command enables the context to configure egress SAP filter policies. If no egress filter is defined, no filtering is performed 7.10.8.2 egress...
Page 493: Table 486 Ingress Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.8.4 ingress Table 486 ingress command Item Description Syntax ingress Context configure>service>vprn Description This command enables the context to configure ingress QoS policies. 7.10.8.5 filter Table 487 filter command Item Description...
Page 494: Table 488 Filter Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.8.6 filter Table 488 filter command Item Description Syntax filter ipv6 ipv6-filter-id no filter [ipv6 ipv6-filter-id] Context configure>service>vprn>interface>sap>egress configure>service>vprn>interface>sap>ingress Description This command associates a IPv6 filter policy with an ingress or egress Service Access Point (SAP).
Page 495: Table 490 Show Gre Tunnel Output
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Parameters gre-tunnel-name — Specifies the name of the GRE tunnel. Tunnel names are from 1 to 32 alphanumeric characters in length. If the string contains special characters (#, $, spaces, etc.), the entire string must be enclosed within double quotes.
Page 496: Table 491 Source Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.8.8 source Table 491 source command Item Description Syntax source ip-address no source Context configure>service>interface>vprn>sap>gre-tunnel Description This command sets the source IPv4 address of GRE encapsulated packets associated with a particular GRE tunnel.
Page 497: Table 493 Delivery-Service Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.8.10 delivery-service Table 493 delivery-service command Item Description Syntax delivery-service {service-id} no delivery-service Context configure>service>interface>vprn>sap>gre-tunnel Description This command sets the delivery service for GRE encapsulated packets associated with a particular GRE tunnel.
Page 498: Table 495 Description Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.8.12 description Table 495 description command Item Description Syntax description <string> no description Context configure>service>interface>vprn>sap>gre-tunnel Default no dscp Description This command sets the description for the GRE tunnel. The no form of this command deletes the description from the GRE tunnel configuration.
Page 499: Table 498 Bgp Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Description This command display information about a particular GRE tunnel or all GRE tunnels. Count option displays the number of GRE tunnels in the system. Parameters gre-tunnel-name —...
Page 500: Table 500 Aggregator-Id-Zero Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.9.3 aggregator-id-zero Table 500 aggregator-id-zero command Item Description Syntax [no] aggregator-id-zero Context configure>service>vprn>bgp configure>service>vprn>bgp>group configure>service>vprn>bgp>group>neighbor Description This command is used to set the router ID in the BGP aggregator path attribute to zero when BGP aggregates routes.
Page 501: Table 502 As-Path-Ignore Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Parameters zero — Specifies that for routes learned without a MED attribute that a zero (0) value is used in the MED comparison. The routes with the lowest metric are the most preferred. infinity —...
Page 502: Table 504 Authentication-Key Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.9.7 authentication-key Table 504 authentication-key command Item Description Syntax authentication-key [authentication-key | hash-key] [hash2] no authentication-key Context configure>service>vprn>bgp configure>service>vprn>bgp>group configure>service>vprn>bgp>group>neighbor Description This command configures the BGP authentication key. Authentication is performed between neighboring routers before setting up the BGP session by verifying the password.
Page 503: Table 506 Auth-Keychain Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Description This command enables the use of bi-directional forwarding (BFD) to control the state of the associated protocol interface. By enabling BFD on a given protocol interface, the state of the protocol interface is tied to the state of the BFD session between the local node and the remote node.
Page 504: Table 508 Damping Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command configures the BGP connect retry timer value in seconds. When this timer expires, BGP tries to reconnect to the configured peer. This configuration parameter can be set at three levels: global level (applies to all peers), peer-group level (applies to all peers in group) or neighbor level (only applies to specified peer).
Page 505: Table 509 Disable-Communities Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.9.12 disable-communities Table 509 disable-communities command Item Description Syntax disable-communities [standard] no disable-communities Context configure>service>vprn>bgp configure>service>vprn>bgp>group configure>service>vprn>bgp>group>neighbor Description This command configures BGP to disable sending communities. Default standard —...
Page 506: Table 512 Export Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.9.15 export Table 512 export command Item Description Syntax export policy [policy...] no export Context configure>service>vprn>bgp configure>service>vprn>bgp>group configure>service>vprn>bgp>group>neighbor configure>service>vprn>rip configure>service>vprn>rip>group configure>service>vprn>rip>group>neighbor Description This command specifies the export policies to be used to control routes advertised to BGP neighbors.
Page 507: Table 514 Group Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.9.17 group Table 514 group command Item Description Syntax group [name] no group Context configure>service>vprn>bgp Description This command creates a context to configure a BGP peer group. The no form of the command deletes the specified peer group and all configurations associated with the peer group.
Page 508: Table 516 Family Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.9.19 family Table 516 family command Item Description Syntax family [ipv4] no family Context configure>service>vprn>bgp>group configure>service>vprn>bgp>group>family>neighbor Description This command specifies the address family or families to be supported over BGP peerings in the base router.
Page 509: Table 518 Ibgp-Multipath Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Default 90 seconds Parameters seconds — The hold-time, in seconds, expressed as a decimal integer. A value of 0 indicates the connection to the peer is up permanently. Values: 0, 3 —...
Page 510: Table 520 Keepalive Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.9.23 keepalive Table 520 keepalive command Item Description Syntax keepalive seconds no keepalive Context configure>service>vprn>bgp configure>service>vprn>bgp>group configure>service>vprn>bgp>group>neighbor Description This command configures the BGP keepalive timer. A keepalive message is sent every time this timer expires.
Page 511: Table 522 Local-As Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Description Configures the local IPv4 or IPv6 address used by the group or neighbor when communicating with BGP peers. Outgoing connections use the local-address as the source of the TCP connection when initiating connections with a peer.
Page 512: Table 523 Local-Preference Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command configures a BGP virtual autonomous system (AS) number. In addition to the AS number configured for BGP in the configure>router>autonomous-system context, a virtual (local) AS number is configured.The virtual AS number is added to the as-path message before the router’s AS number makes the virtual AS the second AS in the as-path.
Page 513: Table 524 Loop-Detect Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Description This command enables setting the BGP local-preference attribute in incoming routes if not specified and configures the default value for the attribute. This value is used if the BGP route arrives from a BGP peer without the local-preference integer set.
Page 514: Table 525 Med-Out Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters drop-peer — Sends a notification to the remote peer and drops the session. discard-route — Discards routes received with loops in the AS path. ignore-loop —...
Page 515: Table 526 Min-As-Origination Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.9.29 min-as-origination Table 526 min-as-origination command Item Description Syntax min-as-origination seconds no min-as-origination Context configure>service>vprn>bgp configure>service>vprn>bgp>group configure>service>vprn>bgp>group>neighbor Description This command configures the minimum interval, in seconds, at which a path attribute, originated by the local router, can be advertised to a peer.
Page 516: Table 528 Multihop Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters seconds — The minimum route advertising interval, in seconds, expressed as a decimal integer. Values: 1 — 255 (2 of 2) 7.10.9.31 multihop Table 528 multihop command Item...
Page 517: Table 530 Next-Hop-Self Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Description This command enables BGP multipath. When multipath is enabled BGP load shares traffic across multiple links. Multipath can be configured to load share traffic across a maximum of 8 routes. If the equal cost routes available are more than the configured value, then routes with the lowest next-hop IP address value are chosen.
Page 518: Table 531 Passive Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.9.34 passive Table 531 passive command Item Description Syntax [no] passive Context configure>service>vprn>bgp>group configure>service>vprn>bgp>group>neighbor Description This command enables passive mode for the BGP group or neighbor. When in passive mode, BGP will not attempt to actively connect to the configured BGP peers but responds only when it receives a connect open request from the peer.
Page 519: Table 533 Preference Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.9.36 preference Table 533 preference command Item Description Syntax [no] preference preference Context configure>service>vprn>bgp configure>service>vprn>bgp>group Description This command configures the route preference for routes learned from the configured peer(s). This configuration parameter can be set at three levels: global level (applies to all peers), group level (applies to all peers in peer-group) or neighbor level (only applies to specified peer).
Page 520: Table 535 Rapid-Withdrawal Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.9.38 rapid-withdrawal Table 535 rapid-withdrawal command Item Description Syntax [no] rapid-withdrawal Context configure>service>vprn>bgp Description This command disables the delay (Minimum Route Advertisement) on sending BGP withdrawals. Normal route withdrawals may be delayed up to the mininum route advertisement to allow for efficient packing of BGP updates.
Page 521: Table 537 Type Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.9.40 type Table 537 type command Item Description Syntax [no] type {internal | external} Context configure>service>vprn>bgp>group configure>service>vprn>bgp>group>neighbor Description This command designates the BGP peer as type internal or external. The type of internal indicates the peer is an IBGP peer while the type of external indicates that the peer is an EBGP peer.
Page 522: Table 539 Area Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.10.2 area Table 539 area command Item Description Syntax [no] area area-id Context configure>service>vprn>ospf Description This command creates the context to configure an OSPF area. An area is a collection of network segments within an AS that have been administratively grouped together.
Page 523: Table 541 Blackhole-Aggregate Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Parameters ip-prefix — The IP prefix in dotted decimal notation for the range used by the ABR to advertise that summarizes the area into another area. Values: 0.0.0.0 —...
Page 524: Table 543 Advertise-Subnet Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command creates a context to configure an OSPF interface. By default interfaces are not activated in any interior gateway protocol such as OSPF unless explicitly configured.
Page 525: Table 545 Authentication-Type Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Description This command configures the password used by the OSPF interface to send and receive OSPF protocol packets on the interface when simple password authentication is configured. All neighboring routers must use the same type of authentication and password for proper protocol communication.
Page 526: Table 546 Dead-Interval Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.10.9 dead-interval Table 546 dead-interval command Item Description Syntax dead-interval seconds no dead-interval Context configure>service>vprn>ospf>area>interface Description This command configures the time, in seconds, that OSPF waits before declaring a neighbor router down.
Page 527: Table 548 Interface-Type Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.10.11 interface-type Table 548 interface-type command Item Description Syntax interface-type {broadcast | point-to-point} no interface-type Context configure>service>vprn>ospf>area>interface Description This command configures the interface type to be either broadcast or point-to-point. Use this command to set the interface type of an Ethernet link to point-to-point to avoid having to carry the broadcast adjacency maintenance overhead if the Ethernet link provided the link is used as a point-to-point.
Page 528: Table 550 Metric Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters keyid — The keyid is expressed as a decimal integer. Values: 1 — 255 md5 key — The MD5 key. The key can be any alphanumeric string up to 16 characters in length.
Page 529: Table 552 Passive Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Description This command configures the OSPF packet size used on this interface. If this parameter is not configured OSPF derives the MTU value from the MTU configured (default or explicitly) in the following contexts: configure>port>ethernet If this parameter is configured, the smaller value between the value configured here and the...
Page 530: Table 554 Retransmit-Interval Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>service>vprn>ospf>area>interface Description This command configures the priority of the OSPF interface that is used an election of the designated router on on the subnet. This parameter is only used if the interface is of type broadcast.
Page 531: Table 555 Transit-Delay Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.10.18 transit-delay Table 555 transit-delay command Item Description Syntax transit-delay seconds no transit-delay Context configure>service>vprn>ospf>area>interface Description This command configures the estimated time, in seconds, that it takes to transmit a link state advertisement (LSA) on the interface.
Page 532: Table 557 Originate-Default-Route Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.10.20 originate-default-route Table 557 originate-default-route command Item Description Syntax originate-default-route [type-7] no originate-default-route Context configure>service>vprn>ospf>area>nssa Description This command enables the generation of a default route and its LSA type (3 or 7) into a Not So Stubby Area (NSSA) by an NSSA Area Border Router (ABR) When configuring an NSSA with no summaries, the ABR will inject a type 3 LSA default route into the NSSA area.
Page 533: Table 559 Summaries Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.10.22 summaries Table 559 summaries command Item Description Syntax [no] summaries Context configure>service>vprn>ospf>area>nssa configure>service>vprn>ospf>area>stub Description This command enables sending summary (type 3) advertisements into a stub area or Not So Stubby Area (NSSA) on an Area Border Router (ABR).
Page 534: Table 562 Asbr Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Default default-metric 1 Parameters metric — The metric expressed as a decimal integer for the default route cost to be advertised into the stub area. Values: 1 —...
Page 535: Table 563 Compatible-Rfc1583 Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.10.26 compatible-rfc1583 Table 563 compatible-rfc1583 command Item Description Syntax [no] compatible-rfc1583 Context configure>service>vprn>ospf Description This command enables OSPF summary and external route calculations in compliance with RFC1583 and earlier RFCs.
Page 536: Table 565 External-Db-Overflow Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.10.28 external-db-overflow Table 565 external-db-overflow command Item Description Syntax external-db-overflow limit interval no external-db-overflow Context configure>service>vprn>ospf Description This command enables limits on the number of non-default AS-external-LSA entries that can be stored in the LSDB and specifies a wait timer before processing these after the limit is exceeded.
Page 537: Table 567 Route Type - Preference
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Description This command configures the preference for OSPF external routes. A route can be learned by the router from different protocols in which case the costs are not comparable;...
Page 538: Table 569 Overload-Include-Stub Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command changes the overload state of the local router so that it appears to be overloaded. When overload is enabled, the router can participate in OSPF routing, but is not used for transit traffic.
Page 539: Table 571 Preference Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Context configure>service>vprn>ospf Description When the router is in an overload state, the router is used only if there is no other router to reach the destination. This command configures the IGP upon bootup in the overload state until one of the following events occur: •...
Page 540: Table 572 Route Type - Preference
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Table 572 Route Type - Preference Route Type Preference Configurable Direct attached Static routes MPLS OSPF interval IS-IS level 1 interval OSPF external IS-IS level 1 exterval Note Preference for OSPF internal routes is configured with the preference command.
Page 541: Table 574 Timers Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Parameters reference-bandwidth — The reference bandwidth in kilobits per second expressed as a decimal integer. Values: 1 — 1000000000 (2 of 2) 7.10.10.35 timers Table 574 timers command Item...
Page 542: Table 576 Lsa-Generate Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.10.37 lsa-generate Table 576 lsa-generate command Item Description Syntax lsa-generate max-lsa-wait [lsa-initial-wait [lsa-second-wait]] no lsa-generate-interval Context configure>service>vprn>ospf>timers Description This parameter customizes the throttling of OSPF LSA-generation. Timers that determine when to generate the first, second, and subsequent LSAs can be controlled with this command.
Page 543: Table 578 Rip Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Parameters max-spf-wait — Specifies the maximum interval in milliseconds between two consecutive SPF calculations. Values: 1 — 120000 Default: 1000 spf-initial-wait — Specifies the initial SPF calculation delay in milliseconds after a topology change.
Page 544: Table 580 Authentication-Type Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>service>vprn>rip configure>service>vprn>rip>group configure>service>vprn>rip>group>neighbor Description This command sets the authentication password to be passed between RIP neighbors. The authentication type and authentication key must match exactly for the RIP message to be considered authentic and processed.
Page 545: Table 581 Check-Zero Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.11.4 check-zero Table 581 check-zero command Item Description Syntax check-zero {enable | disable} no check-zero Context configure>service>vprn>rip configure>service>vprn>rip>group configure>service>vprn>rip>group>neighbor Description This command enables checking for zero values in fields specified to be zero by the RIPv1 and RIPv2 specifications.
Page 546: Table 583 Export Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Default split-horizon enabled (2 of 2) 7.10.11.6 export Table 583 export command Item Description Syntax export policy-name [policy-name…] no export Context configure>service>vprn>rip configure>service>vprn>rip>group configure>service>vprn>rip>group>neighbor Description This command specifies the export policies to be used to control routes advertised to RIP neighbors.
Page 547: Table 585 Message-Size Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Default no import Parameters policy — A route policy statement name. (2 of 2) 7.10.11.8 message-size Table 585 message-size command Item Description Syntax message-size max-num-of-routes no message-size Context configure>service>vprn>rip...
Page 548: Table 587 Metric-Out Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters metric — The value added to the metric of routes received from a RIP neighbor, expressed as a decimal integer. Values: 1 — 16 (2 of 2) 7.10.11.10 metric-out...
Page 549: Table 589 Receive Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Parameters preference — An integer. Values: 1 — 255 Default: 100 (2 of 2) 7.10.11.12 receive Table 589 receive command Item Description Syntax receive receive-type no receive Context configure>service>vprn>rip...
Page 550: Table 591 Timers Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>service>vprn>rip configure>service>vprn>rip>group configure>service>vprn>rip>group>neighbor Description This command specifies the type of RIP messages sent to RIP neighbors. This control can be issued at the global, group or interface level. The default behavior sends RIPv2 messages with the multicast (224.0.0.9) destination address.
Page 551: Table 592 Group Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Parameters update — The RIP update timer value in seconds. Values: 1 — 600 Default: 30 timeout — The RIP timeout timer value in seconds. Values: 1 —...
Page 552: Table 594 Sap-Using Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command creates a context for configuring a RIP neighbor interface. By default, interfaces are not activated in any interior gateway protocol such as RIP unless explicitly configured.
Page 553: Table 595 Show Service Sap Output
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: [port-id | lag-id] vlanid | no-tag • port-id Specifies the physical port ID in the following format: <port-id>...
Page 554: Table 596 Id Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description A.Pol The accounting policy ID assigned to the SAP. The desired state of the SAP. The actual state of the SAP. (2 of 2) 7.10.12.2 Table 596 id command...
Page 555: Table 598 Show All Service-Id Command Output
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Table 598 Show All Service-ID Command Output Label Description Service Detailed Information Service Id The service identifier. Customer Id The customer identifier. Last Status Change The date and time of the most recent change in the administrative or operating status of the service.
Page 556 Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description SAP Statistics Dropped The number of packets or octets dropped. Forwarded In Profile The number of in-profile packets or octets (rate below CIR) forwarded. Forwarded Out Profile The number of out-of-profile packets or octets (rate above CIR) forwarded.
Page 557: Table 599 Arp Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Label Description Peer Sec DNS Addr Specifies a unicast IPv4 address for the secondary DNS server to be signaled to the far-end of the associate PPP/MLPPP link via IPCP extensions. (3 of 3) 7.10.12.4 Table 599...
Page 558: Table 600 Show Service Sap Output
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters ip-address — Displays only ARP entries in the ARP table with the specified IP address. Default: All IP addresses. mac ieee-address — Displays only ARP entries in the ARP table with the specified 48-bit MAC address.
Page 559: Table 601 Base Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Label Description Type Static — FDB entries created by management. Learned — Dynamic entries created by the learning process. OAM — Entries created by the OAM process. The time elapsed since the service was enabled.
Page 560: Table 603 Dhcp Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.12.6 dhcp Table 603 dhcp command Item Description Syntax dhcp Context show>service>id Description This command enables the context to display DHCP information for the specified service. 7.10.12.7 statistics Table 604...
Page 561: Table 605 Show Dhcp Statistics Output
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: [port-id | lag-id] vlanid | no-tag • port-id Specifies the physical port ID in the following format: <port-id>...
Page 562: Table 606 Lease-State Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Client Packets The number of packets received from the DHCP clients that were snooped. Snooped Server Packets The number of packets received from the DHCP server that were discarded. Discarded Server Packets The number of packets received from the DHCP server that were forwarded.
Page 563 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: [port-id | lag-id] vlanid | no-tag • port-id Specifies the physical port ID in the following format: <port-id>...
Page 564: Table 607 Show Dhcp Lease State Output
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Table 607 Show DHCP Lease state Output Label Description IP Address The IPv6 addresses. MAC Address The MAC adresses. Sap/Sdp ID The SAP/SDP identifier. Remaining lifetime The remaining lifetime of the DHCP lease.
Page 565: Table 610 Show Dhcp Summary Output
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Context show>service>id>dhcp Description Displays DHCP configuration summary information. (2 of 2) Table describes the command output fields. Table 610 Show DHCP Summary Output Label Description The configuration identification.
Page 566: Table 612 Show Service-Id Interface Output
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters ip-address — The IP address of the interface for which to display information. Values: 1.0.0.0 — 223.255.255.255 ip-int-name — Specifies the IP interface name for which to display information. detail —...
Page 567: Table 613 Dhcp6 Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Label Description Lease Query Specifies whether the Lease Query is enabled or disabled. Servers Specifies the configured DHCP servers. Gi-Addr Specifies the gateway interface address for DHCP relay. Gi-Addr as Src Ip Specifies whether GI address should be used as the source IP address for DHCP relay packets.
Page 568: Table 615 Show Dhcp6 Summary Output
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Table 615 Show DHCP6 Summary Output Label Description Interface Name Name of the interface. SapId The configuration identification. Used/Max Relay Used — The number of lease-states that are currently in use on a specific interface, that is, the number of clients on that interface got an IP address by DHCP.
Page 569: Table 618 Show Dhcp Lease State Detailed Output
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Label Description Sap/Sdp ID The SAP/SDP identifier. Remaining lifetime The remaining lifetime of the DHCP lease. Lease origin The lease origin. (2 of 2) Table describes the detailed command output fields. Table 618 Show DHCP Lease state Detailed Output Label...
Page 570: Table 620 Show Dhcp6 Statistics Output
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Table describes the command output fields. Table 620 Show DHCP6 Statistics Output Label Description Packets Received The number of packets received from the DHCP clients. Packets Transmitted The number of packets transmitted to the DHCP clients.
Page 571: Table 622 Show Service Sap Output
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: [port-id | lag-id] vlanid | no-tag • port-id Specifies the physical port ID in the following format: <port-id>...
Page 572: Table 623 Aggregate Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Flags Specifies the conditions that affect the operating status of this SAP. Display output includes: ServiceAdminDown, SapAdminDown, InterfaceAdminDown, PortOperDown, PortMTUTooSmall, L2OperDown, SapIngressQoSMismatch, SapEgressQoSMismatch, RelearnLimitExceeded, RxProtSrcMac, ParentIfAdminDown, NoSapIpipeCeIpAddr, TodResourceUnavail, TodMssResourceUnavail, SapParamMismatch, CemSapNoEcidOrMacAddr, StandByForMcRing, ServiceMTUTooSmall, SapIngressNamedPoolMismatch,...
Page 573: Table 624 Show Router Aggregate Output
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Table 624 Show Router Aggregate Output Label Description Prefix Displays the destination address of the aggregate route in dotted decimal notation. Summary Specifies whether the aggregate or more specific components are advertised. AS Set Displays an aggregate where the path advertised for the route consists of all elements contained in all paths that are being summarized.
Page 574: Table 627 Bgp Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Interface The IP interface name associated with the ARP entry. No. of ARP Entries The number of ARP entries displayed in the list. (2 of 2) 7.10.12.18 Table 627 bgp command...
Page 575 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Description This command displays BGP routes with have been dampened due to route flapping. This command can be entered with or without a route parameter. When the keyword detail is included, more detailed information displays.
Page 576: Group
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Peer AS The autonomous system number of the advertising router. Peer Router-Id The router ID of the advertising router. Local Pref BGP local preference path attribute for the route. The time elapsed since the service was enabled.
Page 577 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Table 632 Show Group Output Label Description Group BGP group name Group Type No Type — Peer type not configured. External — Peer type configured as external BGP peers. Internal —...
Page 578: Neighbor
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Remove Private Disabled — BGP will not remove all private AS numbers from the AS path attribute in updates sent to the neighbor in the peer group. Enabled —...
Page 579 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Description This command displays BGP neighbor information. This command can be entered with or without any parameters. When this command is issued without any parameters, information about all BGP peers displays.
Page 580 Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description State Idle — The BGP peer is not accepting connections. Active — BGP is listening for and accepting TCP connections from this peer. Connect — BGP is attempting to establish a TCP connection from this peer. Open Sent —...
Page 581 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Label Description Num of Flaps The number of flaps in the neighbor connection. Recd. Paths The number of unique sets of path attributes received from the BGP neighbor. IPv4 Recd.
Page 582: Paths
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Remote capability Export Policy The configured export policies for the peer group. Import Policy The configured import policies for the peer group. (4 of 4) Table describes the command output fields for both the standard and detailed information for a neighbor.
Page 583: Routes
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Table describes the command output fields for BGP path. Table 637 Show BPG Path Output Label Description BGP Router ID The local BGP router ID. The configured autonomous system number. Local AS The configured local AS setting.
Page 584 Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command displays BGP route information. When this command is issued without any parameters, then the entire BGP routing table displays. When this command is issued with an IP prefix/mask or IP address, then the best match for the parameter displays.
Page 585 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Table 639 Show BGP Routes Output Label Description BGP Router ID The local BGP router ID. The configured autonomous system number. Local AS The configured local AS setting. If not configured, then the value is the same as the Network Route IP prefix and mask length for the route.
Page 586: Summary
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.12.25 summary Table 640 summary command Item Description Syntax summary [all] summary [family family] [neighbor ip-address] Context show>router>bgp Description This command displays a summary of BGP neighbor information. If confederations are not configured, that portion of the output will not display.
Page 587: Interface
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Label Description Total BGP Routes The total number of BGP routes learned from BGP peers. Total BGP Paths The total number of unique sets of BGP path attributes learned from BGP peers. Total Path Memory Total amount of memory used to store the path attributes.
Page 588 Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Table 643 Show IP Interface Standard Output Label Description Interface-Name The IP interface name. Type n/a — No IP address has been assigned to the IP interface, so the IP address type is not applicable.
Page 589 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Label Description Port Id The port ID of the IP interface. Egress Filter The egress IP filter policy ID associated with the IP interface. none — Indicates no egress filter policy is associated with the interface. Ingress Filter The ingress IP filter policy ID associated with the IP interface.
Page 590: Dhcp6
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.12.27 dhcp6 Table 646 dhcp6 command Item Description Syntax dhcp6 Context show>router Description This command enables the context to display DHCP6 related information. 7.10.12.28 statistics Table 647 statistics command Item Description...
Page 591: Summary
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Label Description Client Packets The number of packets received from the DHCP clients that were forwarded. Relayed Client Packets The number of packets received from the DHCP clients that were snooped. Snooped Server Packets The number of packets received from the DHCP server that were discarded.
Page 592: Neighbour
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Table 651 routes command Item Description Syntax routes [interface ip-int-name [ip-prefix/prefix-length]] Context show>router>dhcp6 Description This command displays the routes for DHCP6. If no IP address or interface name is specified, then all configured routes are displayed. If an IP address or interface name is specified, then only data regarding the specified route is displayed.
Page 593: Database
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Label Description Interface Displays the name of the IPv6 interface name. MAC Address Specifies the link-layer address. State Displays the current administrative state. Displays the number of seconds until the entry expires. Type Displays the type of IPv6 interface.
Page 594: Neighbor
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Table 656 Show RIP Route Database Output Label Description Destination The RIP destination for the route. Displays how many seconds the specific route will remain in the routing table. When an entry reaches 0, it is removed from the routing table.
Page 595 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Label Description Down — The RIP neighbor interface is operationally down. Up — The RIP neighbor interface is operationally up. Primary IP The primary IP address of the RIP neighbor interface. Send Mode Bcast —...
Page 596: Peer
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Metric In The metric value added to routes received from a RIP neighbor. Metric Out The value added to routes exported into RIP and advertised to RIP neighbors. Split Horizon Disabled —...
Page 597: Statistics
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Label Description Last Update The number of days since the last update. No. of Peers The number of RIP peers. (2 of 2) 7.10.12.36 statistics Table 662 statistics command Item Description...
Page 598 Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Triggered Updates Total — The total number of triggered updates sent. These updates are sent before the entire RIP routing table is sent. Last 5 Min — The number of triggered updates that were sent in the last 5 minutes. Last 1 Min —...
Page 599: Route-Table
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Label Description RIPv2 Requests Received Total — The total number of times the router received RIPv2 route requests from other routers. Last 5 Min — The number of times the router received RIPv2 route requests from other routers in the last 5 minutes.
Page 600: Rtr-Advertisement
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Next Hop The next hop IP address for the route destination. Type Local — The route is a local route. Remote — The route is a remote route. Protocol The protocol through which the route was learned.
Page 601: Static-Route
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Label Description Nbr Solicitation Tx The number of neighbor solicitations sent and time since they were sent. Nbr Advertisement Tx The number of neighbor advertisements sent and time since they were sent. Rtr Advertisement Rx The number of router advertisements received and time since they were received.
Page 602: Summary
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Table describes the standard command output fields for the route table. Table 669 Show Route Table Standard Output Label Description IP Addr/mask The static route destination address and mask. Pref The route preference value for the static route.
Page 603: Clear Commands
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Label Description Info Option Indicates whether Option 82 is enabled. Admin State Indicates the administrative status. (2 of 2) 7.10.13 Clear Commands 7.10.13.1 Table 672 arp command Item Description Syntax...
Page 604: Statistics
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.13.3 statistics Table 674 statistics command Item Description Syntax statistics Context clear>router>dhcp6 Description This command clears DHCP6 statistics. 7.10.13.4 forwarding-table Table 675 forwarding-table command Item Description Syntax forwarding-table Context...
Page 605: Table 677 Damping Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.13.6 damping Table 677 damping command Item Description Syntax damping [[ip-prefix/ip-prefix-length] [neighbor ip-address]] | [group name] Context clear>router>bgp Description This command clears or resets the route damping information for received routes. Parameters ip-prefix/prefix-length —...
Page 606: Table 679 Neighbor Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.13.8 neighbor Table 679 neighbor command Item Description Syntax neighbor {ip-address | as as-number | external | all} [soft | soft-inbound] neighbor {ip-address | as as-number | external | all} statistics neighbor ip-address end-of-rib Context clear>router>bgp...
Page 607: Table 681 Database Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.10.13.10 database Table 681 database command Item Description Syntax database Context clear>router>rip Description This command flushes all routes in the RIP database. 7.10.13.11 statistics Table 682 statistics command Item Description...
Page 608: Table 684 Id Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.13.13 Table 684 id command Item Description Syntax id service-id Context clear>service clear>service>statistics Description This command clears parameters for a specific service. Parameters service-id — The ID that uniquely identifies the service to clear. 7.10.13.14 statistics Table 685...
Page 609: Table 687 Sap Command
FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Item Description Description Clears lease state statistics for DHCP6. Parameters ip-prefix/prefix-length - The destination address of the aggregate route. Values: ipv6-prefix x:x:x:x:x:x:x:x (eight 16-bit pieces) x:x:x:x:x:x:d.d.d.d x: [0 —...
Page 610: Table 688 Stp Command
Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: [port-id | lag-id] vlanid | no-tag • port-id Specifies the physical port ID in the following format: <port-id>...
Page 611: Mirror Services
These are, at best, only able to mirror from one port to another on the same device. Nokia Service Mirroring extends and integrates these capabilities into the network and provides significant operational benefits. Each system can mirror packets from a defined set of ports to any destination point in the network.
Page 612: Mirror Source And Destinations
Mirror Services FD 100/320Gbps NT and FX NT IHub Services Guide Nokia’s implementation of packet mirroring is based on two assumptions: • Packets in ingress direction are mirrored as they appear on the wire. This is important for troubleshooting encapsulation and protocol issues. When mirroring at ingress, the HW sends an exact copy of the original ingress packet to the mirror destination while normal forwarding proceeds on the original packet.
Page 613: Figure 35 Local Mirroring Example
FD 100/320Gbps NT and FX NT IHub Services Guide Mirror Services Figure 35 Local Mirroring Example ALA-A 2/1/1 2/1/2 2/1/3 Sniffer Configure a mirror service specifying source and destination parameters 8.3 Configuration Notes This section describes mirroring configuration caveats. • 1 mirroring service ID may be created within a single system.
Page 614: Basic Mirroring Configuration
Mirror Services FD 100/320Gbps NT and FX NT IHub Services Guide 8.4 Basic Mirroring Configuration Destination mirroring parameters must include at least: • A mirror destination ID (same as the mirror source service ID). • A mirror destination. Mirror source parameters must include at least: •...
Page 615: Figure 36 Local Mirrored Service Tasks
FD 100/320Gbps NT and FX NT IHub Services Guide Mirror Services Figure 36 Local Mirrored Service Tasks Mirror Source 1/1/2 ALA-A Mirror Destination 1/1/3 1/1/1 1/1/2 1/1/3 Sniffer 8.6 Mirror Service CLI Command Reference This section shows the following command hierarchies: •...
Page 616: Table 689 Description Command
Mirror Services FD 100/320Gbps NT and FX NT IHub Services Guide 8.6.3 Show Commands show — mirror mirror-dest [service-id] 8.7 Mirror Service CLI Configuration Commands The following commands are described: • Generic Commands • Mirror Configuration Commands • Debug Configuration Commands •...
Page 617: Table 690 Shutdown Command
FD 100/320Gbps NT and FX NT IHub Services Guide Mirror Services 8.7.1.2 shutdown Table 690 shutdown command Item Description Syntax [no] shutdown Context configure>mirror>mirror-dest debug>mirror-source Description The shutdown command administratively disables an entity. When disabled, an entity does not change, reset, or remove any configuration settings or statistics. Many entities must be explicitly enabled using the no shutdown command.
Page 618: Table 691 Mirror-Dest Command
Mirror Services FD 100/320Gbps NT and FX NT IHub Services Guide 8.7.2 Mirror Configuration Commands 8.7.2.1 mirror-dest Table 691 mirror-dest command Item Description Syntax mirror-dest service-id no mirror-dest Context configure>mirror Description This command creates a context to set up a service that is intended for packet mirroring. It is configured as a service to allow mirrored packets to be directed locally (within the same router).
Page 619: Table 692 Sap Command
FD 100/320Gbps NT and FX NT IHub Services Guide Mirror Services 8.7.2.2 Table 692 sap command Item Description Syntax sap sap-id no sap Context configure>mirror>mirror-dest Description This command creates a service access point (SAP) within a mirror destination service. It also associates a predefined SAP within another service ID to a mirror source.
Page 620: Table 693 Port And Encapsulation Type Values
Mirror Services FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: [port-id | lag-id] vlanid | no-tag • port-id Specifies the physical port ID in the following format: <port-id>...
Page 621: Table 694 Mirror-Source Command
FD 100/320Gbps NT and FX NT IHub Services Guide Mirror Services 8.7.3 Debug Configuration Commands 8.7.3.1 mirror-source Table 694 mirror-source command Item Description Syntax [no] mirror-source service-id Context debug Description This command configures mirror source parameters for a mirrored service. The mirror-source command is used to enable mirroring of packets specified by the association of the mirror-source to sources of packets defined within the context of the mirror-dest-service-id.
Page 622 Mirror Services FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command enables mirroring of traffic ingressing or egressing a port (Ethernet port, or Link Aggregation Group (LAG)). The port command associates a port or LAG to a mirror source. The port is identified by the port-id.
Page 623: Table 696 Cpu-Port Command
FD 100/320Gbps NT and FX NT IHub Services Guide Mirror Services 8.7.3.3 cpu-port Table 696 cpu-port command Item Description Syntax cpu-port {port-id | lag lag-id} {[egress] [ingress]} cpu-no port {port-id | lag lag-id} [egress] [ingress] Context debug>mirror-source Description This command enables mirroring of traffic ingressing a port that has the CPU as destination or traffic leaving the CPU and egressing the port.
Page 624: Table 698 Show Mirror-Dest Command Output
Mirror Services FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context show>mirror Description Displays mirror configuration and operation information. Parameters service-id - Specify the mirror service ID. (2 of 2) Table describes the command output fields. Table 698 Show Mirror-dest Command Output Label Description...
Page 625 Customer document and product support Customer documentation Customer Documentation Welcome Page Technical Support Product Support Portal Documentation feedback Customer Documentation Feedback...

This manual is also suitable for:

7330 7360

Nokia 7302 Manual

Preface

Getting Started

Services Overview

Virtual Leased Line Services

4 Virtual Leased Line Services

Quick Links

Related Manuals for Nokia 7302

Summary of Contents for Nokia 7302