Page 1
Introduction Fundamental safety instructions Description SINUMERIK Operator control and display elements SINUMERIK 840D sl Machine Pushbutton Panel: MPP Mounting 464 IE H Connecting Equipment Manual Initialization Service and maintenance Technical data Spare parts/accessories Valid for: Control system SINUMERIK 840D sl/840DE sl SINUMERIK ONE 03/2021 A5E50810237B AA...
Page 2
Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
1.2.1 Structure, content, target group, ... Validity This Equipment Manual deals with the MPP 464 IE H Machine Pushbutton Panel. This documentation is valid for the systems SINUMERIK 840D sl and SINUMERIK ONE. Target group This Equipment Manual addresses planners, installers and configuration engineers in the field of automation technology.
This document may contain hyperlinks to third-party websites. Siemens is not responsible for and shall not be liable for these websites and their content. Siemens has no control over the information which appears on these websites and is not responsible for the content and information provided there.
Feedback on the technical documentation If you have any questions, suggestions or corrections regarding the technical documentation which is published in the Siemens Industry Online Support, use the link "Send feedback" link which appears at the end of the entry.
Page 8
Siemens support on the go With the award-winning "Siemens Industry Online Support" app, you can access more than 300,000 documents for Siemens Industry products – any time and from anywhere. The app can support you in areas including: • Resolving problems when implementing a project •...
• Certificates • Product announcements and much more The "Siemens Industry Online Support" app is available for Apple iOS and Android. Data matrix code on the nameplate The data matrix code on the nameplate contains the specific device data. This code can be read with a smartphone and technical information about the device displayed via the "Industry...
Page 10
Introduction 1.7 Important product information Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
• Only use power supplies that provide SELV (Safety Extra Low Voltage) or PELV- (Protective Extra Low Voltage) output voltages for all connections and terminals of the electronics modules. Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Page 12
• Tighten the screws with the torque specified in the technical documentation. • Use a torque wrench or a mechanical precision nut runner with a dynamic torque sensor and speed limitation system. Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Page 13
• Therefore, if you move closer than 20 cm to the components, be sure to switch off radio devices or mobile telephones. • Use the "SIEMENS Industry Online Support app" only on equipment that has already been switched off. WARNING...
– Wearing ESD shoes or ESD grounding straps in ESD areas with conductive flooring • Only place electronic components, modules or devices on conductive surfaces (table with ESD surface, conductive ESD foam, ESD packaging, ESD transport container). Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Siemens’ products and solutions undergo continuous development to make them more secure. Siemens strongly recommends that product updates are applied as soon as they are available and that the latest product versions are used. Use of product versions that are no longer supported, and failure to apply the latest updates may increase customer’s exposure to cyber...
Page 17
6. Influence of network-connected communication systems, e.g. ripple-control transmitters or data communication via the network For more information about the residual risks of the drive system components, see the relevant sections in the technical user documentation. Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Page 18
Fundamental safety instructions 2.5 Residual risks of power drive systems Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Description Overview The MPP 464 IE H Machine Pushbutton Panel (IE = Industrial Ethernet, H = handheld unit connection) enables user-friendly operation of machine functions at complex machining stations. It is suitable for machine-level operation of milling, turning, grinding and special machines.
• Free space for a second override switch System configuration The MPP 464 IE H is integrated into the control system in the same way as the MPP 483 IE (see chapter "System features" in the "MPP 483 IE" manual).
Description 3.4 Interfaces Interfaces 3.4.1 Overview Figure 3-2 Rear and side view of MPP 464 IE H with interfaces Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Page 23
Table 3-6 User keys Position num‐ Inter‐ Designation Max. cable Type face length ⑲ Individual wiring 100 m RJ45 ⑳ ① ② ③ Extension 100 m RJ45 ④ Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Reference potential S3, S11 S_S11.43 NO contact S3, S11 3.4.2.2 COM board Pin assignment For details, see "Pin assignment of the interfaces" (Page 45) in the Section "Connecting". Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Page 27
Reference potential NC contacts S7 ... S10 S_S7 NO contact S7 S_S8 NO contact S8 S_S9 NO contact S9 S_S10 NO contact S10 BZ S_S7-10 Reference potential NO contacts S7 ... S10 Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Page 28
Ext. key S56 LED_S56 Ext. key S57 LED_S57 Ext. key S58 LED_S58 Viewed from the PCB: B: at top of plug connector A: at bottom of plug connector Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Page 29
N.C. Not assigned N.C. Not assigned Receive data - N.C. Not assigned N.C. Not assigned Note Only connect the Ethernet interfaces to the LAN, not to telecommunication networks. Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Page 30
The connector is only used to assist looping through. The connected pins 1 and 2 as well as 3 and 4 have no additional function on the connection module. Enabling X20 Connector designa‐ tion: Connector type: MCV 1.5/8-G3.81 Cable length (max.): 30 m Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
To unlatch the emergency stop button, turn it to the left. When the emergency stop button is activated, the emergency stop chain of the MPP 464 IE H will ensure personal safety and protect the machine in hazardous situations.
Mounting space with blanking cover for EKS identification system ⑦ Handheld unit connection HT2/ HT8 ⑧ Emergency stop override button Figure 4-1 Standard version MPP 464 IE H Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Page 37
Command devices can be connected at the following locations according to the table in the chapter "Accessories and spare parts" > "Displays and operator controls": • S1 to S4 • S7 to S10 Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Busfault Assembled PCB customer keys Diagnostics LEDs LED1 (H1) Voltage monitoring of customer keys LED2 (H2) Voltage monitoring of customer keys LED3 (H3) Voltage monitoring of customer keys Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Page 39
Operator control and display elements 4.3 Rear side Assembled PCB handheld unit connection ① Figure 4-3 Rear MPP 464 IE H with LEDs on HGA board HT 8 Color Meaning LED1 (H1) Green X1 RJ45 Connection established LED2 (H2) Yellow...
Page 40
Operator control and display elements 4.3 Rear side Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
225 ± 0.5 100 + 15 *) plus 40 mm when using signal line handwheel 6FX8002-2CB00-1Axy. Clearance for adjacent devices: external device dimensions + at least 2 mm all-round Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Page 42
• Corner radius R5 or chamfer 5x45° • Sealing area circumferential 7+1 mm Tension jacks The MPP 464 IE H is attached to the rear of the operator panel using 8 clamps (included in the scope of supply). The tightening torque is 0.4 Nm. Note The distance to the next MPP all around must be at least 1 mm.
Page 43
3. Change the lamp using service tool LZ6 or a suitable insulating tube 4. Reinstall the key carrier and button cap in reverse order. Lamp remover LZ6 is not a SIEMENS product. It can be obtained from Schlegel: Georg Schlegel GmbH & Co. KG...
Page 44
Mounting Note When using LEDs, make sure that they are connected with the correct polarity, see figure: "Mounting position LEDs MPP 464 IE H". Mounting additional operator controls According to the specifications of the respective manufacturer. Inserting the slide-in labels Note Slide in the labels when the MPP is not yet installed.
KT3_IN Customer key 3 Ground Universal input X52 Connector designation: Connector type: Male connector, 4-pin Signal name Signal type Meaning KT4_IN Customer key 4 KT5_IN Customer key 5 Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Page 48
When using an external power supply, make sure that the fuse used has a tripping rating that corresponds to the maximum possible short-term short-circuit current of the power supply unit used. Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
0.85 m Table 6-1 Assignment of connector X11 Name Type Meaning Direct key 1 DT16 Direct key 16 + 5 V (fused) + 5 V (fused) Ground Ground Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Damage to the device caused by unfused supply voltages The 24 V DC power supply must always be grounded and designed as Protective Extra-Low Voltage (PELV) - protection by functional extra low voltage with safe isolation! Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
• Fuse according to UL248: 1.6 A. If you use the encoder supply X20:A15/A16 or VS1/VS2 of the ET200S block 4/8 F DI 24 VDC PROFIsafe, the external fuse can be omitted. Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
In addition to the B10d value of the emergency stop button, the B10d value of S11 must also be considered for the assessment in both emergency stop circuits. Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Page 56
3, PL d according to EN ISO 13849-1:2008 can be met with this measure. Wire these contacts accordingly. All other functions can be found in the following figure: Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Page 57
Signal to PLC: triggers time monitoring. If the signal level is still "Low" or "Open" after the monitoring time has elapsed (max. 5 min), the PLC must trigger an EMERGENCY OFF. Figure 6-6 Handheld unit connection HT 8 Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
The following circuit diagram relates to the lights in HS1 to HS4 and HS7 to HS10, see figure "Individual wiring of customer keys" in chapter "Customer keys". Figure 6-7 External control of the indicator lights Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Page 59
Connecting 6.6 Circuits and wiring System wiring Figure 6-8 System wiring Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Page 60
Connecting 6.6 Circuits and wiring Connection of direct keys Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
("Waiting for Client"). LEDs on the COM board The LEDs on the COM board of the MPP 464 IE H (rear) are not controlled by the software. They are used exclusively to signal the hardware states, e.g. "Power supply OK".
Page 62
Once communication has taken place, the software version is only displayed again after the power to the MPP 464 IE H has been switched OFF and ON. Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
• Mechanical vibration and shock • Dust • Humidity • Strong magnetic fields Checking the emergency stop button Check the emergency stop button regularly to ensure that it functions correctly. Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Page 64
• Unusual or no functioning • Unusual heat generation • Smoke development Repair Send the device back to the manufacturer for repair. The device must only be repaired there. Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Temperature limit values (storage) -20 ... 55° C (cyclic) Temperature limit values (operation) 0 ... 45° C (front) 0 ... 55° C (rear) Temperature change Max. 30 K/h Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Page 66
The use of aggressive compounds and additives can damage components and result in their failure. Avoid contact between the operator components with coolants and lubricants, as resistance to all coolants and lubricants cannot be guaranteed. Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
(EN 60947-5-1) Rated operational voltage 24 V 24 V AC-12 10 A AC-15 Switching capacity DC-12 10 A DC-13 Min. rated operating current at 5 V 1 mA Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Page 68
0.7 A / output L signal Max. signal level 2 V (idling) 0.3 mA Short-circuit protection Typ. response threshold 1.1 A RMS short-circuit current 0.5 A Electrical isolation Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
European Community: • 2014/30/EU "Electromagnetic Compatibility" (EMC Directive) • Directive 2011/65/EC on the restriction of the use of certain hazardous substances in electrical and electronic devices (RoHS II) Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
The products described in this manual can be mostly recycled due to the fact that they contain very few damaging substances. To recycle and dispose of your old device in an environmentally friendly way, please contact an appropriate disposal company. Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Spare parts/accessories 10.1 Overview Numerous spare parts and accessories are available for the MPP 464 IE H. Contact your Siemens representative to order accessories and spare parts. A connecting cable is available for connecting the handwheels, see Chapter "Connection of the handwheels (Page 73)".
Page 72
Schlegel or 3SU1 following selection BP20 ... BP23 signaling devices from Low-Voltage Controls and Distribu‐ tion Catalog (LV 1) EKS identification sys‐ Serial interface EKS-A-ISX-G01-ST09/03 BP17 tem Euchner Interface EKS-A-IDX-G01-ST09/03 PROFIBUS DP Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Nameplate of the cable with article number, length in m, manufacturer, month/year of manu‐ facture ② Pin cable lug ③ Ring cable lug ④ Flexible cable 0.75 mm Figure 10-1 Connecting cable for handwheel Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...
Marking of the keys of the MPP 464 IE H in the standard version The figure shows the marking of the keys of the MPP 464 IE H in the standard version. You can create your own slide-in labels to label the keys differently. A printable blank film (DIN A4) is supplied with the panel for this purpose.
Page 75
Files for printing the blank film For printing the blank film, the DOConCD contains two files as a ZIP file in the "Slide-in/Labelling Templates" folder: • Template_MPP 483.doc [assignment for the standard variant of the MPP 464 IE H - (A)] • SymbolsMPP483.doc [(B)] Note You can find more information on the slide-in labels on the Internet: https://support.industry.siemens.com/cs/ww/en/view/107745917...
Page 77
2. Place the blank film in the printing direction in the slot of your laser printer (see figure: "Blank film for MPP 464 IE H membrane keyboard"). 3. Select "film" as the printable medium if your printer allows this setting.
Page 78
– Draw the graphic or add an image in the center of this square. – Copy the graphic and square and add them both to the file "Template_MPP483.doc". Machine Pushbutton Panel: MPP 464 IE H Equipment Manual, 03/2021, A5E50810237B AA...