hit counter script
  1. Manuals
  2. Brands
  3. Maco Manuals
  4. Indoor Furnishing
  5. MULTI POWER
  6. Aassembly instructions

Maco MULTI POWER Aassembly Instructions

Hide thumbs Also See for MULTI POWER:
Table of Contents

Advertisement

Quick Links

Download this manual
www.maco.eu
ASSEMBLY INSTRUCTIONS
MULTI POWER
in thresholds
TECHNOLOGY IN MOTION
only by certified specialists!
TILT AND TURNHARDWARE
Use

Advertisement

Table of Contents
loading

Related Manuals for Maco MULTI POWER

Summary of Contents for Maco MULTI POWER

  • Page 1 TECHNOLOGY IN MOTION www.maco.eu ASSEMBLY INSTRUCTIONS MULTI POWER in thresholds only by certified specialists! TILT AND TURNHARDWARE...

  • Page 2: Table Of Contents

    Table of Contents Item Page Important Information Key and Abbreviations General processing instructions 6 - 10 Proper Use Application notes 6 - 9 Application diagram Threshold Transit Personal 11 - 17 Basic processing instructions Cross-section sash, cross-section packer profile 12 - 13 Hardware installation on the frame 14 - 17 Floor threshold Transit extendable with strip gasket 18 - 26...
  • Page 3 Table of Contents Item Page Roto Eifel TB Threshold 65 - 76 Basic processing instructions Cross-section frame installation, cross-section sash, cross-section 66 - 68 Hardware installation on the frame 69 - 74 Hardware installation on the sash 75 - 76 Ground threshold Profine A075 or A076 77 - 90 Basic processing instructions Cross-section frame installation, cross-section sash, cross-section 78 - 80 Hardware installation on the frame...

  • Page 4: Important Information

    Important Information Target audience This documentation is intended exclusively for specialist companies and certified specialists. The work-steps described here in may only be carried out by certified specialists. Instructions for use • Unless otherwise indicated, measurements are made in millimetres. • Mount all hardware parts professionally as described in this manual and observe all safety instructions. • All diagrams are only symbolic. • Further technical documents can be found in our online catalogue (TOM) at extranet.maco.eu. • This print document is constantly being revised and is available for download in the current version at www.maco.eu. • Printing errors, mistakes and changes are reserved. • Please send feedback or suggestions and ideas for improvements on our instructions by email to: feedback@maco.eu Material notes •...

  • Page 5: Key And Abbreviations

    Key and Abbreviations Sash rebate height (SRH) Backset (DM) Rebate Gap (FL) Sash rebate width (SRW) Rebate Leg (Ü) Sash rebate width and height Maximum sash weight Offset (V) Rebate depth (FT) Turn and Tilt Element (DK) MMKS MULTI-MATIC (MM) Tilt and Turn element (KD) MMKS MULTI-MATIC Turn-only element (DR) with tilt-lock bolt (MM-KS) AWD = Application diagram = central lock WINDOWS · DOORS · SLIDING DOORS...

  • Page 6: General Processing Instructions

    General processing instructions Intended Use These assembly instructions for the hinge side MULTI POWER in thresholds are binding. The use and assembly of the components is only permitted in the manner listed below. Any other use is not provided for and therefore does not correspond to the intended use. The following points also need to be considered: • Information on application areas, sash weights and fabrication guidelines from profile manufacturers or system providers must be considered in a binding manner! • The centre of gravity or position of the glass pane can affect application areas and max. weights and must be requested if necessary! In the event of non-compliance, no claims will be considered! Application notes Application materials (frame material) Timber* Aluminum * only Transit threshold Applications / Sash version WINDOWS ·...
  • Page 7 Window design * see assembly instructions Order Number 757332 Type of opening Opening distance ≤ 100° Hardware program MMKS WINDOWS · DOORS · SLIDING DOORS...
  • Page 8 Hardware overview (security) EN 1627 RC 1 - 6 Fitting groove The fitting groove must be implemented according to the information in our Print and Online Catalogues! Frame rebate FT 24 FT 18 IMPORTANT! TIMBER: The pivot post must be fully flat! Glue grooves in frame! FT 30 FT 20 WINDOWS · DOORS · SLIDING DOORS...
  • Page 9 Screw dimension For fixing the corner support and scissor stay support in timber and PVC profiles, a special screw Ø 4.5 x 38 mm, Article No. 362918 (Phillips) or 367828 (TX 20) must be used. Use a Ø 3.9 x 25 mm screw for fixing in aluminum. DANGER! The fixing of the bearing parts must meet the requirements of the TBDK guidelines (quality ∅7,2 association for locks and hardware - www.schloss- industrie de) or comply with EN 13126-8! ∅4,5 IMPORTANT! ∅3,9 Use screws as long as possible to fix the ∅4,5 rebated corner support. DIN 7982 C № 362918 At least Ø 4.0 x 30 mm! № 367828 With PVC, the fixing with screws must be done in the steel reinforcement! Any other case must be consulted with us! WINDOWS...

  • Page 10: Application Diagram

    Application diagram kg/ m² 2800 IMPORTANT! 2600 Some systems might cause limits to maximum 2400 sash weights. Note the weight specifications for 2200 each version! 2000 1800 1600 1400 1200 ≤ 150 kg 1000 ≤ 3,0 m² ≤ 30 kg ≤ 1,0 m² 1000 1200 1400 1600 1650 Allowable area...

  • Page 11: Threshold Transit Personal

    80 kg, the packer Article No. 473860 must be used! The application diagram applies The application diagram applies to MULTI POWER with a maximum sash to MULTI POWER with a maximum weight of 150 kg! sash weight of 110 kg! If a load transfer device is additionally...

  • Page 12: Cross-Section Sash, Cross-Section Packer Profile

    Sash cross-section Profile with sash gasket IMPORTANT! When using a cover cap for the MULTI POWER pivot post, the rebate gap must be a minimum of 13 mm (without cap profile)! ATTENTION! The distance of the sash to the floor should be a minimum of 5 mm, to prevent small items on the floor causing damage. Profile with frame gasket WINDOWS · DOORS · SLIDING DOORS...
  • Page 13 Packer profile cross-section Examples IMPORTANT! The threshold with frame must be packed along the entire length. The load must be carried by the packer profile! IMPORTANT! The length of the packer profile must be flush on both sides with the frame outer edge. IMPORTANT! Threshold The inner edge of the Packer profile / sub-structure threshold must be flush with the packer profile.

  • Page 14: Hardware Installation On The Frame

    Hardware installation on the frame Pre-drilling for pivot post Insert drill jig Article No. 217092 (right) or 217093 (left) as shown and pre-drill with Ø 3 mm drill. WINDOWS · DOORS · SLIDING DOORS...
  • Page 15 Insert pivot post (Article No. 215812, FT24 9V right bzw. 215813, FT24 9V left) or 215810 (FT24 13V right) or 215811 (FT24 13V left) and fix in position. IMPORTANT! Maximum sash weight 130 kg. From a sash weight of 80 kg, the packer Article No. 473890 must be used (lower diagram). IMPORTANT! Fixing screws must be chosen in such a way that the screw heads are no more than 7.2 mm in diameter. They must not protrude above the base plate! IMPORTANT! Fixing screws for the pivot post must not be Horizontal:...
  • Page 16 Apply cover cap Article No. 364498 (right) or 364499 (left). Open pivot post fully. H ang the cover cap into the corner area. C lip the cover cap into the baseplate. Rebate gap lower horizontal minimum 13 mm! WINDOWS · DOORS · SLIDING DOORS...
  • Page 17 Cover profile Cut the rest profile to length with the cover cap and insert it into the threshold. T o remove the cover cap, the rest profile must be removed beforehand! WINDOWS · DOORS · SLIDING DOORS...

  • Page 18: Floor Threshold Transit Extendable With Strip Gasket

    110 kg 150 kg The application diagram applies The application diagram applies to to MULTI POWER with a maximum MULTI POWER with a maximum sash sash weight of 110 kg! weight of 150 kg! If a load transfer device is additionally...

  • Page 19: Cross-Section Sash, Cross-Section Packer Profile

    Sash cross-section IMPORTANT! When using a cover cap for the MULTI POWER pivot post, the rebate gap must be a minimum of 13 mm (without cap profile)! ATTENTION! The distance of the sash to the floor should be a minimum of 5 mm, to prevent small items on the floor causing damage. NOTE! *Gasket track must be flush sideways with the sash rebate! Only the threshold with a construction height of 24 mm is permitted in the...
  • Page 20 Packer profile cross-section Example IMPORTANT! The threshold with frame must be packed along the entire length. The load must be carried by the packer profile! IMPORTANT! The length of the packer profile must be flush on both sides with the frame outer edge. IMPORTANT! Further information on the Transit threshold can be found in the assembly instructions Order No. 750097.

  • Page 21: Adjusting The Floor Threshold For Multi Power

    Adjusting the threshold for MULTI POWER Set the width of the rail (see also assembly instructions for Transit threshold Order No. 750097). Depending on the rebate depth, shorten the width of the adapter ; with ← a → rebate depth less than 42 mm, the thermal isolation must also be milled down. WINDOWS · DOORS · SLIDING DOORS...
  • Page 22 Adjust the adapter to the width of the frame ← a →; shorten the aluminium profile to the length of the adapter ← b →. WINDOWS · DOORS · SLIDING DOORS...
  • Page 23 Screw the adapter onto the frame and onto the threshold and seal the joints of the threshold with silicone. Frame profile: Vertical screw Ø 2.9 x 9.5 mm Threshold: Vertical screw Ø 5.0 × 50 mm WINDOWS · DOORS · SLIDING DOORS...

  • Page 24: Hardware Installation On The Frame

    Hardware installation on the frame Insert pivot post Article No. 215812 (FT24 9V right) or 215813 (FT24 9V left) or 215810 (FT24 13V right) or 215811 (FT24 13V left) and fix in the open state. IMPORTANT! Maximum sash weight 130 kg. IMPORTANT! Fixing screws must be chosen in such a way that the screw heads are no more than 7.2 mm in diameter. They must not protrude above the base plate! IMPORTANT! Fixing screws for the pivot post must not be over-tightened! IMPORTANT! General MULTI POWER...
  • Page 25 Fix threshold with packer IMPORTANT! Maximum sash weight 130 kg. IMPORTANT! Fixing screws must be chosen in such a way that the screw heads are no more than 7.2 mm in diameter. They must not protrude above the base plate! IMPORTANT! Fixing screws for the pivot post must not be over-tightened! IMPORTANT! General MULTI POWER assembly instructions...
  • Page 26 Apply cover cap Article No. 364498 (right) or 364499 (left). Open pivot post fully. H ang the cover cap into the corner area. C lip the cover cap into the baseplate. Rebate gap lower horizontal minimum 13 mm! WINDOWS · DOORS · SLIDING DOORS...

  • Page 27: Ground Threshold Grundmeier Combi

    Aluminium The application diagram applies The application diagram applies to version, not for the PVC to MULTI POWER with a maximum MULTI POWER with a maximum sash version! sash weight of 110 kg! weight of 150 kg!

  • Page 28: Cross-Section Frame Installation, Cross-Section Sash, Cross-Section

    Frame cross-section „Alternative fixing” This „alternative fixing” processing guideline from Grundmeier KG must always be performed in a binding manner! Otherwise, our data regarding weight etc. cannot be adhered to! W ith the „alternative fixing”, the screw connection is done from below through the threshold into the PVC frame profile. If the „alternative fixing” version in the profile channels of the plastic profile is not possible and the use of a filler core is considered, it is imperative to contact us beforehand for advice! This version of the connection with a filler core is not approved by us! WINDOWS · DOORS · SLIDING DOORS...
  • Page 29 Sash cross-section * W hen using a cover cap with the MULTI POWER pivot post, the rebate gap must be at least 18.5 mm (without cover cap profile)! WINDOWS · DOORS · SLIDING DOORS...
  • Page 30 Packer profile cross-section Example IMPORTANT! The threshold with frame must be packed along the entire length. The load must be carried by the packer profile! IMPORTANT! The length of the packer profile must be flush on both sides with the frame outer edge. IMPORTANT! > 2/3*T The width of the packer > 50 profile must be a minimum of 2/3 of the Threshold...

  • Page 31: Hardware Installation On The Frame

    Hardware installation on the frame C ut the threshold to length (observe the manufacturer's instructions). Mill out the pivot post recess. F or depth, see point 3 - cross-section representation Milling for threshold in the pivot post area Allowed area of milling below the frame profile (straight milling section) Connect the threshold and threshold holder with the frame according to the specifications of Grundmeier KG. Rebate surface for pivot post must be maintained T he base plate of the pivot post must be attached flush to the rebate surface at the rear to accommodate the maximum sash weight.
  • Page 32 Pre-drilling for pivot post Ø3 Ø3 227810 227810 Insert drilling jig Article No. 227810 as shown and pre-drill with Ø 3 mm drill. * Do not use a hole (no bush)! WINDOWS · DOORS · SLIDING DOORS...
  • Page 33 Drilling pattern horizontal Drilling pattern vertical WINDOWS · DOORS · SLIDING DOORS...
  • Page 34 V ertical packer for profile adjustment (see catalogue 12.14 for list of profile adjustments) IMPORTANT! Observe MULIT POWER fixing instructions for single PVC profile systems (756991)! (applies to profiles without reinforcement and profiles with fixing outside of the reinforcement.) Separate the vertical part of the packer and cut to length in such a way that the packer does not collide with the threshold holder. The drill holes of the packer must be aligned with the drill holes of the frame profile. Insert the vertical part of the packer in the profile (horizontal part is not required), but do not yet fix it in place. Horizontal packer for threshold adjustment Push the packer for the threshold adjustment into the groove, Article No. 369939. The drill holes of the packer must be aligned with the drill holes of the threshold.
  • Page 35 I nsert pivot post Article No. 227286 (right) or 227287 (left) and fix in place. IMPORTANT! Fixing screws must be chosen in such a way that the screw heads are no more than 7.2 mm in diameter. They must not protrude above the base plate! IMPORTANT! Fixing screws for the pivot post must not be over-tightened! IMPORTANT! General MULTI POWER assembly instructions and supplied package leaflets must be observed in a binding manner!
  • Page 36 Apply cover cap Article No. 364498 (right) or 364499 (left). Open pivot post fully. H ang the cover cap into the corner area. C lip the cover cap into the baseplate. Rebate gap below horizontal at least 12.5 mm! WINDOWS · DOORS · SLIDING DOORS...
  • Page 37 Rest profile Cut the rest profile to length with the cover cap and insert it into the threshold. T o remove the cover cap, the rest profile must be removed beforehand! WINDOWS · DOORS · SLIDING DOORS...
  • Page 38 Fix the threshold with the packer. P re-drill the threshold in the pivot post area, lower it in and fix into the packer with the longest possible screws! The screws must not be smaller than Ø 5 x 50 mm. WINDOWS · DOORS · SLIDING DOORS...

  • Page 39: Hardware Installation On The Sash

    Hardware installation on the sash Attachment for corner support R emove fixing part by pushing the wedge (1.) and lifting upwards (2.). I nsert attachment Article No. 368390 into the corner of the corner support (1.) and then press into the recess (2.). WINDOWS · DOORS · SLIDING DOORS...
  • Page 40 Corner support I nsert corner support Article No. 215804 (right) or 215805 (left) in the fitting groove and fix with Ø 4 x 30 mm screws. The screw length must be chosen in such a way that it protrudes sufficiently through the fitting groove base. However, it must not collide with the steel reinforcement. Assemble weather bar profile with gaskets and lateral end caps according to manufacturer instructions WINDOWS · DOORS · SLIDING DOORS...

  • Page 41: Threshold Trocal Z029

    150 kg 130 kg The application diagram applies The application diagram applies to to MULTI POWER with a maximum MULTI POWER with a maximum sash sash weight of 130 kg! weight of 150 kg! If a load transfer device is additionally...
  • Page 42 Cross-section Frame T he processing guidelines of Trocal GmbH (Profine Group) must always be adhered to in a binding manner! O therwise, our data regarding weight etc. cannot be adhered to! T he connection of the frame profile and the threshold must be carried out exactly according to the specifications of Trocal GmbH. The standard version of the connection of the frame and threshold by means of a filler core has been tested by us and is approved for the specified formats and weights. All other versions are not approved by us! Any other case must be consulted with us! WINDOWS · DOORS · SLIDING DOORS...
  • Page 43 Sash cross-section * W hen using a cover cap for the MULTI POWER pivot post, the rebate gap must be at least 13 mm! D epending on the weather bar used, the gasket may collide with the hardware. To avoid this, the bottom rebate gap must be increased! WINDOWS · DOORS · SLIDING DOORS...
  • Page 44 Packer profile cross-section Example IMPORTANT! The threshold with frame must be packed along the entire length. The load must be carried by the packer profile! IMPORTANT! The length of the packer profile must be flush on both sides with the frame outer edge. IMPORTANT! The width of the packer profile must be a minimum of 2/3 of the > 2/3*T threshold depth, but no >...

  • Page 45: Hardware Installation On The Frame

    Hardware installation on the frame C ut the threshold to length (observe the manufacturer's instructions). Connect the threshold and frame with milling contour according to the specifications of Trocal GmbH (Profine Group). Pre-drilling for pivot post. Ø3 Ø3 217092 217093 Insert drill jig Article No. 217092 (right) or 217093 (left) as shown and pre-drill with Ø 3 mm drill. * Do not use a hole (no bush)! WINDOWS · DOORS · SLIDING DOORS...
  • Page 46 Drilling pattern horizontal 16,5 Drilling pattern vertical 16,5 WINDOWS · DOORS · SLIDING DOORS...
  • Page 47 V ertical packer for profile adjustment IMPORTANT! Pay attention to MULTI POWER screw fixing instructions for single PVC profile systems (756991). (applies to profiles without reinforcement and profiles with fixing outside of the reinforcement). Separate vertical part of the packer Article No. 364174 or 364175. Insert the vertical part of the packer in the profile (horizontal part is not required). T he drill holes of the packer must be aligned with the drill holes of the frame profile. Horizontal packer for threshold adjustment Insert the base for the threshold adjustment Article No. 369945 into the recess, this clamps slightly in the contour. The drill holes of the packer must be aligned with the drill holes of the threshold. WINDOWS · DOORS · SLIDING DOORS...
  • Page 48 I nsert pivot post Article No. 215810 (right) or 215811 (left) and fix in place. IMPORTANT! Fixing screws must be chosen in such a way that the screw heads are no more than 7.2 mm in diameter. They must not protrude above the base plate! IMPORTANT! Fixing screws for the pivot post must not be over-tightened! IMPORTANT! General MULTI POWER assembly instructions and supplied package leaflets must be observed in a binding manner!
  • Page 49 Apply cover cap Article No. 365224 (right) or 365225 (left). Open pivot post fully. H ang the cover cap into the corner area. C lip the cover cap into the baseplate. Rebate gap below horizontal at least 13 mm! WINDOWS · DOORS · SLIDING DOORS...
  • Page 50 Fix the threshold with the packer. P re-drill the threshold in the pivot post area, lower it in and fix into the packer with the longest possible screws! The screws must not be smaller than Ø 5 x 50 mm. WINDOWS · DOORS · SLIDING DOORS...

  • Page 51: Hardware Installation On The Sash

    Hardware installation on the sash Corner support I nsert corner support Article No. 215804 (right) or 215805 (left) insert into fitting groove and fix with Ø 4 x 30 mm screws. The screw length must be chosen in such a way that it protrudes sufficiently through the fitting groove base. However, it must not collide with the steel reinforcement. Assemble weather bar profile with gaskets and lateral end caps according to manufacturer’s instructions. WINDOWS · DOORS · SLIDING DOORS...

  • Page 52: Ground Threshold Veka

    110 kg 150 kg The application diagram applies The application diagram applies to to MULTI POWER with a maximum MULTI POWER with a maximum sash sash weight of 110 kg! weight of 150 kg! If a load transfer device is additionally...

  • Page 53: Cross-Section Frame Installation, Cross-Section Sash, Cross-Section

    Frame cross-section T he processing guidelines of VEKA AG must always be adhered to in a binding manner! O therwise, our data regarding weight etc. cannot be adhered to! T he connection of the frame profile and the threshold must be carried out exactly according to the specifications of VEKA AG. The above-shown connection of the frame and threshold by means of flange connectors , foldable connectors and contour milling on the frame has been tested by us and is approved for the specified formats and weights. It should be noted that the reinforcement in the frame profile reaches all the way down. All other versions are not approved by us! Any other case must be consulted with us! WINDOWS · DOORS · SLIDING DOORS...
  • Page 54 Sash cross-section * W hen using a cover cap for the MULTI POWER pivot post, the rebate gap must be at least 19 mm (without cover cap profile)! WINDOWS · DOORS · SLIDING DOORS...
  • Page 55 Packer profile cross-section Example IMPORTANT! The threshold with frame must be packed along the entire length. The load must be carried by the packer profile! IMPORTANT! The length of the packer profile must be flush on both sides with the frame outer edge. IMPORTANT! The width of the > 2/3*T packer profile must be > 50 a minimum of 2/3 of the threshold depth, but no less than 50 mm.

  • Page 56: Hardware Installation On The Frame

    Hardware installation on the frame C ut the threshold to length (observe the manufacturer's instructions). Connect the threshold and frame with milling contour according to the specifications of VEKA AG. * Do not set the screw! Ø3 Pre-drilling for pivot post. Ø3 217094 217094 Insert drill jig Article No. 217094 as shown and pre-drill with Ø 3 mm drill. * Do not use a hole (no bush)! WINDOWS · DOORS · SLIDING DOORS...
  • Page 57 Drilling pattern horizontal Drilling pattern vertical WINDOWS · DOORS · SLIDING DOORS...
  • Page 58 Packer for threshold Insert packer for threshold Article No. 369973 (right) or 369974 (left) in the frame rebate corner. Fix the packer horizontally with three Ø 4.3 x 13 mm screws. Do not fix the large screw hole at the front (* = fixing in the packer) yet! WINDOWS · DOORS · SLIDING DOORS...
  • Page 59 I nsert pivot post Article No. 215814 (right) or 215815 (left) and fix in place. IMPORTANT! Fixing screws must be chosen in such a way that the screw heads are no more than 7.2 mm in diameter. They must not protrude above the base plate! IMPORTANT! Fixing screws for the pivot post must not be over-tightened! IMPORTANT! General MULTI POWER assembly instructions and supplied package leaflets must be observed in a binding manner!
  • Page 60 Apply cover cap Article No. 365224 (right) or 365225 (left). Open pivot post fully. H ang the cover cap into the corner area. C lip the cover cap into the baseplate. Rebate gap below horizontal at least 19 mm! WINDOWS · DOORS · SLIDING DOORS...
  • Page 61 Fix the threshold with the packer. P re-drill the threshold at the front screw hole of the packer and fix it into the packer with the longest possible screws. The screws must not be smaller than Ø 5 x 50 mm. WINDOWS · DOORS · SLIDING DOORS...
  • Page 62 IMPORTANT! To remove the cover cap, the threshold cap must be removed beforehand! C ut the cap to length with the cover cap and insert it into the threshold. WINDOWS · DOORS · SLIDING DOORS...

  • Page 63: Hardware Installation On The Sash

    Hardware installation on the sash Attachment for corner support R emove fixing part by pushing the wedge (1.) and lifting upwards (2.). I nsert attachment Article No. 368390 into the corner of the corner support (1.) and then press into the recess (2.). WINDOWS · DOORS · SLIDING DOORS...
  • Page 64 Corner support I nsert corner support Article No. 215804 (right) or 215805 (left) in the fitting groove and fix with Ø 4 x 30 mm screws. The screw length must be chosen in such a way that it protrudes sufficiently through the fitting groove base. However, it must not collide with the steel reinforcement. Assemble weather bar profile with gaskets and lateral end caps according to manufacturer’s instructions. WINDOWS · DOORS · SLIDING DOORS...
  • Page 65 The application diagram applies The application diagram applies to threshold manufacturer, to MULTI POWER with a maximum MULTI POWER with a maximum sash along with a steel sash weight of 110 kg! weight of 150 kg! reinforcement in a size...
  • Page 66 Frame cross-section T he processing guidelines of Roto Frank AG must always be adhered to in a binding manner! Otherwise, our data regarding weight etc. cannot be adhered to! T he connection of the frame profile and the threshold must be carried out exactly according to the specifications of the profile manufacturer and in combination with Roto Frank AG. The standard version of the connection of the frame and threshold using a threshold holder with screw fixing in the profile channel has been tested by us and is approved for the specified formats and weights. All other versions (e.g. alternative fixing in the filler core) are not approved by Any other case must be consulted with us. WINDOWS · DOORS · SLIDING DOORS...
  • Page 67 Sash cross-section * W hen using a cover cap with the MULTI POWER pivot post, the rebate gap must be at least 18.5 mm (without cover cap profile)! WINDOWS · DOORS · SLIDING DOORS...
  • Page 68 Packer profile cross-section Example IMPORTANT! The threshold with frame must be packed along the entire length. The load must be carried by the packer profile! IMPORTANT! The length of the packer profile must be flush on both sides with the frame outer edge. IMPORTANT! Threshold Packer profile / sub-structure To support 110 kg sash weight, the use of a sub-structure with suitable reinforcement is mandatory. The...
  • Page 69 Hardware installation on the frame Cut the threshold to length (observe the manufacturer's instructions). Connect the floor threshold and threshold connector with the frame according to the specifications of the profile manufacturer and the threshold manufacturer. Pre-drilling for pivot post. Screw on the steel reinforcement in the substructure profile and then connect the substructure profile to the threshold. Ø3 Ø3 227810 227810 Insert drill jig Article No. 227810 as shown and pre-drill with Ø 3 mm drill. * Do not use a hole (no bush)! WINDOWS · DOORS · SLIDING DOORS...
  • Page 70 Drilling pattern horizontal Drilling pattern vertical WINDOWS · DOORS · SLIDING DOORS...
  • Page 71 V ertical packer for profile adjustment IMPORTANT! Pay attention to MULTI POWER screw fixing instructions for single PVC profile systems (756991) (applies to profiles without reinforcement and profiles with fixing outside of the reinforcement). Separate the vertical part of the packer Article no. 364076 or 364077 and cut to length in such a way that the packer does not collide with the threshold holder. The drill holes of the packer must be aligned with the drill holes of the frame profile. Insert the vertical part of the packer in the profile (horizontal part is not required). Horizontal packer for threshold adjustment 369944 Insert the packer for the threshold adjustment Article No. 369944 into the recess, this clamps slightly in the contour. The drill holes of the packer must be aligned with the drill holes of the threshold. WINDOWS · DOORS · SLIDING DOORS...
  • Page 72 I nsert pivot post Article No. 227286 (right) or 227287 (left) and fix in place. IMPORTANT! Fixing screws must be chosen in such a way that the screw heads are no more than 7.2 mm in diameter. They must not protrude above the base plate! IMPORTANT! Fixing screws for the pivot post must not be over-tightened! IMPORTANT! General MULTI POWER assembly instructions and supplied package leaflets must be observed in a binding manner!
  • Page 73 Apply cover cap Article No. 364498 (right) or 364499 (left). Open pivot post fully. H ang the cover cap into the corner area. C lip the cover cap into the baseplate. Rebate gap below horizontal at least 13 mm! WINDOWS · DOORS · SLIDING DOORS...
  • Page 74 Fix the threshold with the packer. Pre-drill the threshold and packer in the pivot post area, lower it in and fix into the sub-structure with the longest possible screws! The screw must protrude at least 40 mm into the sub-structure. WINDOWS · DOORS · SLIDING DOORS...
  • Page 75 Hardware installation on the sash Attachment for corner support Remove fixing part by pushing the wedge (1.) and lifting upwards (2.). Insert attachment Article No. 368390 into the corner of the corner support (1.) and then press into the recess (2.). WINDOWS · DOORS · SLIDING DOORS...
  • Page 76 Corner support Insert corner support Article No. 215804 (right) or 215805 (left) in the fitting groove and screw in place. The screw length must be chosen in such a way that it protrudes sufficiently through the fitting groove base. However, it must not collide with the steel reinforcement. A ssemble weather bar profile with gaskets and lateral end caps according to manufacturer’s instructions. WINDOWS · DOORS · SLIDING DOORS...
  • Page 77 100 kg 150 kg The application diagram applies The application diagram applies to to MULTI POWER with a maximum MULTI POWER with a maximum sash sash weight of 100 kg! weight of 150 kg! If a load transfer device is additionally...
  • Page 78 Frame cross-section T he processing guidelines of Profine GmbH must always be adhered to in a binding manner! Otherwise, our data regarding weight etc. cannot be adhered to! T he connection of the frame profile and the threshold must be carried out exactly according to the specifications of Profine GmbH. The above shown connection with threshold holder has been tested by us and is approved for the specified formats and weights. All other versions (e.g. alternative fixing in the filler core) are not approved by Any other case must be consulted with us! WINDOWS · DOORS · SLIDING DOORS...
  • Page 79 Sash cross-section * W hen using a cover cap for the MULTI POWER pivot post, the rebate gap must be at least 18.5 mm (without cover profile)! WINDOWS · DOORS · SLIDING DOORS...
  • Page 80 Packer profile cross-section Example IMPORTANT! The threshold with frame must be packed along the entire length. The load must be carried by the packer profile! IMPORTANT! The length of the packer profile must be flush on both sides with the frame outer edge. IMPORTANT! The width of the packer > 2/3*T profile must be a >...
  • Page 81 Hardware installation on the frame C ut the threshold to length (observe the manufacturer's instructions). Mill out the pivot post recess. for depth, see point 3 - cross-section representation Milling for threshold in the pivot post are (straight part of the milling) Milling in the area under the frame profile permitted C onnect the threshold and threshold holder with the frame according to the specifications of Profine GmbH. The base plate of the pivot post must be attached flush to the rebate surface at the rear to accommodate the maximum sash weight. Rebate surface for pivot post must be maintained WINDOWS ·...
  • Page 82 S lide the faceplate into the threshold chamber. ≥30 Pre-drilling for pivot post Ø3 Ø3 227810 227810 Insert drill jig Article No. 227810 as shown and pre-drill with Ø 3 mm drill. * Do not use a hole (no bush)! WINDOWS · DOORS · SLIDING DOORS...
  • Page 83 Drilling pattern horizontal Drilling pattern vertical WINDOWS · DOORS · SLIDING DOORS...
  • Page 84 V ertical packer for profile adjustment. IMPORTANT! Observe MULIT POWER fixing instructions for single PVC profile systems (756991)! (applies to profiles without reinforcement and profiles with fixing outside of the reinforcement.) Separate the vertical part of the packer Article no. 367262 or 367263 and cut to length in such a way that the packer does not collide with the threshold holder. The drill holes of the packer must be aligned with the drill holes of the frame profile. Insert the vertical part of the packer in the profile (horizontal part is not required), but do not yet fix it in place. WINDOWS · DOORS · SLIDING DOORS...
  • Page 85 I nsert pivot post Article No. 227286 (right) or 227287 (left) and fix in place. IMPORTANT! Fixing screws must be chosen in such a way that the screw heads are no more than 7.2 mm in diameter. They must not protrude above the base plate! IMPORTANT! Fixing screws for the pivot post must not be over-tightened! IMPORTANT! General MULTI POWER assembly instructions and supplied package leaflets must be observed in a binding manner!
  • Page 86 Apply cover cap Article No. 364498 (right) or 364499 (left). Open pivot post fully. H ang the cover cap into the corner area. C lip the cover cap into the baseplate. Rebate gap below horizontal at least 12.5 mm! WINDOWS · DOORS · SLIDING DOORS...
  • Page 87 Fix the threshold with the packer. P re-drill the threshold in the pivot post area, lower it in and fix into the packer with the longest possible screws! The screws must not be smaller than Ø 5 x 50 mm. WINDOWS · DOORS · SLIDING DOORS...
  • Page 88 Threshold cover IMPORTANT! To remove the cover cap, the threshold cap must be removed beforehand! C ut the threshold cap to length with the cover cap and insert it into the threshold. WINDOWS · DOORS · SLIDING DOORS...
  • Page 89 Hardware installation on the sash Attachment for corner support Remove fixing part by pushing the wedge (1.) and lifting upwards (2.). Insert attachment Article No. 368390 into the corner of the corner support (1.) and then press into the recess (2.). WINDOWS · DOORS · SLIDING DOORS...
  • Page 90 Corner support Insert corner support Article No. 215804 (right) or 215805 (left) in the fitting groove and screw in place. The screw length must be chosen in such a way that it protrudes sufficiently through the fitting groove base. However, it must not collide with the steel reinforcement. A ssemble weather bar profile with gaskets and lateral end caps according to manufacturer’s instructions. WINDOWS · DOORS · SLIDING DOORS...

  • Page 91: Additional Information

    Additional information Hinging and unhinging of the sash Information on the hinging and unhinging of the sash can be found in the assembly instructions Order No. 757332. Adjusting of pivot post and scissor stay hinge All adjustment information can be found in the maintenance and adjustment instructions Order No. 757070EN.
  • Page 92 MACO MULTI-MATIC Satisfied? MAYER & CO We look forward to your BESCHLÄGE GMBH feedback@maco.eu Alpenstraße 173 Created: February 2019 - Changed: 04.03.2020 A-5020 Salzburg Order no. 757905 All rights reserved and subject to change. Tel.: +43 662 6196-0 This print document is revised regularly. The latest version is available at E-Mail: maco@maco.eu https://www.maco.eu/assets/757905...

Table of Contents