Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to
Wear eye
instructions
protection
1. SAFETY
DANGER! BE AWARE, LEAD-ACID BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS
REASON, IT IS VERY IMPORTANT TO READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY, EACH TIME YOU USE THE
BATTERY TESTER.
Follow these instructions and those published by the battery and vehicle manufacturers, and the maker of any equipment you intend
to use in the vicinity of the battery. Remember to review warning marks on all products and on engines.
1.1.
PERSONAL PRECAUTIONS
ensure that there is another person within hearing range and close enough to come to your aid, should a problem arise when working
9
near a lead-acid battery.
Wear safety eye protection and protective clothing. Avoid touching eyes while working near battery.
9
Have fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes.
9
Wash immediately with soap and water if battery acid contacts skin or clothing. if acid enters eye, flush eye immediately with cool, clean
9
running water for at least 15 minutes and seek immediate medical attention.
remove personal metallic items such as rings, bracelets, necklaces and watches. A lead-acid battery can produce a short-circuit current
9
which is high enough to weld such items to the vehicle and cause severe burns.
ensure that hands, clothing (especially belts) are clear of fan blades and other moving or hot parts of engine. remove ties and contain
9
long hair.
DO NOT smoke or allow a spark or flame in the vicinity of the battery or engine.
8
1.2.
GENERAL SAFETY
familiarise yourself with the application, limitations and potential hazards of the tester. Also refer to the vehicle manufacturer's hand
9
book. IF IN ANY DOUBT CONSULT A QUALIFIED VEHICLE ELECTRICIAN.
ensure that the tester is in good condition before use. if in any doubt do not use the unit and contact a qualified vehicle electrician.
9
only use recommended attachments and parts. to use unapproved items may be dangerous and will invalidate your warranty.
9
Keep tools and other items away from the engine and ensure that you can see the battery and working parts of engine clearly.
9
determine the system voltage before using the tester.
9
if the tester receives a sharp knock or blow the unit must be checked by a qualified service agent before using.
9
if the battery terminals are corroded or dirty clean them before using the tester.
9
Keep children and unauthorised persons away from the work area.
9
DO NOT disassemble the tester for any reason. the tester must only be checked by qualified service personnel.
8
WARNING! To prevent the risk of sparking, short circuit and possible explosion DO NOT drop metal tools in the battery area, or allow
‰
them to touch the battery terminals.
DO NOT cross-connect tester to battery. ensure positive (red) clamp is to positive terminal and negative (blAcK) clamp is to negative
8
terminal. if battery symbols cannot be distinguished, remember that the negative terminal is the one directly connected to the vehicle
bodywork.
DO NOT use the tester outdoors, or in damp, or wet locations and DO NOT use in the vicinity of flammable liquids or gases.
8
ensure there is effective ventilation to prevent a build-up of explosive gases.
9
DO NOT use the tester for a task for which it is not designed.
8
When not in use, store the tester carefully in a safe, dry, childproof location.
9
2. INTRODUCTION
Professional diagnosis of battery and alternator faults. tests battery condition with as little as 1V of residual charge. no heat, no sparks and no
misdiagnosis. checks condition of starter – no complicated connections or interpretation required. Analyses the vehicle's charging system at rest
and under load to determine condition of the alternator. connect the bt2002.V2 and follow the prompts on the lcd screen for straightforward
answers. incorporates simple voltmeter for voltage tests and additional system diagnostics. rugged construction.
© Jack sealey limited
instructions for
DIGITAL BATTERY & ALTERNATOR TESTER
BT2002.V2
model no:
Wear
Wear
protective
protective
clothing
gloves
Original Language Version
Warning:
Warning:
explosive
corrosive
material
substance
bt2002.V2| issue:1 30/05/17
Advertisement
Related Manuals for Sealey BT2002.V2
Summary of Contents for Sealey BT2002.V2
- Page 1 – no complicated connections or interpretation required. Analyses the vehicle’s charging system at rest and under load to determine condition of the alternator. connect the bt2002.V2 and follow the prompts on the lcd screen for straightforward answers.
- Page 2 3. SPECIFICATION model no: ..............bt2002.V2 rated battery Voltage ............. 6-12V charging system capability ......... 12, 24V rated systems ........sAe, din, en, iec, Jis test range ....... 40-2100ccA en, 40-2000ccA sAe, ..............30-1500ccA iec ..............25-1300ccA din ............bY bAtterY tYPe Jis minimum power requirement ..........
- Page 3 Contact your local solid waste authority for recycling information. Battery Removal Remove battery from tester. Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705. NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.