hit counter script
Download Print this page
NEC NEAX 2000 Cheat Sheet
NEC NEAX 2000 Cheat Sheet

NEC NEAX 2000 Cheat Sheet

Ip ccis trunking to ipk
Hide thumbs Also See for NEAX 2000:

Advertisement

Quick Links

Page 1 of 6
Here is an example of IP CCIS trunking to an NEC IPK. IP addressing, trunk, route, and station numbers
are for example only. The programming examples for either system can be used for connection to any
other like system or the NEAX 2400.
Originating Point Code 00001
IPTB IP Address 192.168.1.100
Gateway/Route Address
192.168.1.1
Station 200
Before you start with the IPS you should......
1. Confirm the revision of the IPTB card to be version B2 2.06 or higher. Check the white revision
sticker on the board or in programming with CM F85>XX11>, CM F85>XX>12, and CM
F85>XX13> where XX = the sense wheel of the IPTB board.
2. Confirm the 3 cables from the IPTB board to the VCTI boards are connected as per the IVS2 IP
Manual (rev 3) Chapter 2 page 29. Do this wrong and you will smell smoke.
3. The IPTB board with VCTI cards have very specific power requirements in that depending on the
number of cards to be installed you must have vacant slots available in the PIM. These conditions
MUST be confirmed with the IVS2 IP Manual (rev 3) Chapter 2 page 27.
4. VCTI boards can be mounted in LT slots 08~11 if required.
5. Out of the box the IPTB boards on the NEAX 2000 are defaulted to G729a voice compression.
The IPK IAD card does G 7.11. Obviously one side MUST be changed.
6. The IPTB board CAN be set for 10 or 100 Mbps (MODE Rotary SW and SW2) but in either
setting the data is at half duplex only.
7. Fax is available through the IPTB but modem data communication is not.
8. CM F88 must have 1 CCIS license (F88>05>) and 1 IP license (F88>11>) for each IPTB installed
in the system. Total of 8 IPTB's can be installed each with 4 VCTI's (total of 128 IP CCIS trunks).
9. See item 5 in "Before you start with the IPK you should.....".
IP CCIS Trunking to IPK
WAN/LAN
NEAX 2000 Cheat Sheet
Originating Point Code 00002
IAD IP Address 192.168.2.150
Gateway/Route Address
192.168.2.1
Station 300

Advertisement

loading

Summary of Contents for NEC NEAX 2000

  • Page 1 IP CCIS Trunking to IPK Here is an example of IP CCIS trunking to an NEC IPK. IP addressing, trunk, route, and station numbers are for example only. The programming examples for either system can be used for connection to any other like system or the NEAX 2400.
  • Page 2 Page 2 of 6 NEAX 2000 Cheat Sheet Before you start with the IPK you should…… 1. Load Service pack 4 to the IAD board and the Key System must be at minimum R2500. CPU software must be either 2.5, 3.5, 4.5, 4.6 or 4.7 to support IP_CCIS.
  • Page 3 Page 3 of 6 NEAX 2000 Cheat Sheet Feature Programming NEAX 2000 IPS Programming for the IPS with IPTB board in LT06 and VCTI boards in LT07 and LT08. LT slots 09, 10, and 11 are empty. The IPTB Sense wheel is on a 08. IP addressing, trunk, route, and station numbers are for example only.
  • Page 4 Page 4 of 6 NEAX 2000 Cheat Sheet System Programming Elite IPK 1. MB 7-1 assign the card as a DTI (8) 2. MB 1-11-03 assign CCIS over IP as YES 3. MB 1-11-05 turn ON the first 8 line keys 4.
  • Page 5: Neax 2000Ips

    Page 5 of 6 NEAX 2000 Cheat Sheet 11. Click on the Port Tab on the top of the screen. Change the preference to G.729 (The 2000 is set for G.729) Uncheck the use all available Codec’s for incoming calls...
  • Page 6 5. For QOS go to and assign either IP Precedence or DiffServ to protocols to the main page of the IAD card. 6. For CCIS Voice Codec. The IAD is default G711. NEAX 2000 default is G729. One side should be changed.

This manual is also suitable for:

Neax 2400