PIONEER Service Manual. A subscription to, or additional copies Also test with plug reversed of, PIONEER Ser vice Manual may be obtained at a (Using AC adapter Earth nominal charge from PIONEER. plug as required)
Page 3
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. PDP-R05E...
5. PCB PARTS LIST ............................114 6. ADJUSTMENT ............................. 132 6.1 HOW TO ENTER SERVICE FACTORY MODE..................132 6.2 POSSIBLE CASES WHERE READJUSTMENT IS REQUIRED ............132 6.3 USING RS-232C COMMANDS......................133 6.4 ADJUSTMENT ITEMS ........................... 134 6.5 TRAP SWITCH ............................137 PDP-R05E...
Page 5
6.8 LIST OF RS-232C COMMANDS ......................156 6.9 OUTLINE OF COMMANDS........................159 7. GENERAL INFORMATION ...........................164 7.1 DIAGNOSIS............................164 7.1.1 TROUBLESHOOTING........................164 7.1.2 DISASSEMBLY ..........................177 7.2 EXPLANATION ............................180 7.2.1 PROCESSING IN ABNORMALITY ....................180 7.2.2 SEQUENCE .............................184 7.3 PARTS ..............................185 7.3.1 IC..............................185 7.4 CLEANING .............................210 8. PANEL FACILITIES ............................211 PDP-R05E...
1. SPECIFICATIONS Item Media Receiver, Model:PDP-R05XE Media Receiver, Model:PDP-R05E Colour System Analogue PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60 Digital PAL/SECAM Not Applicable TV Function Receiving System B/G,D/K,I,L/L ’ (Analogue) Tuner VHF/UHF E2 –E69ch,F2 –F10ch,I21 –I69ch,IR A –IR Jch CATV Hyper-band,S1 –S41ch Auto Channel Preset...
Page 7
Only the power cord that is appropriate in your country or Remote control unit region is supplied. (AXD1491) AA size battery x 2 Screw x 4(for stand) Screw hole cap x 4 (Manganese battery) (PMB40P120FTB) (AMR3386) Stand System cable (3 m) T wo operating instructions (AXG1009) (ADF1026) PDP-R05E...
For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING SECTION 1, 26, 27, 29, 30, 33, 34 ×4 ×4 PDP-R05E...
Page 9
IM Pad See Contrast table (2) Top Pad See Contrast table (2) Accessory Box See Contrast table (2) (2) CONTRAST TABLE PDP-R05E/WYVI, /WYVIXK, PDP-R05XE/WYVIXK, PDP-R05FE/WYVI and / WYVIXK are constructed the same except for the following: PDP-R05E/ PDP-R05E/ PDP-R05XE/ PDP-R05FE/ PDP-R05FE/...
2.2 EXTERIOR SECTION (1) PDP-R05XE only Except PDP-R05FE PDP-R05XE only Refer to "2.3 EXTERIOR SECTION (2)". Refer to "2.4 FRONT PANEL SECTION". PDP-R05E...
Page 12
(2) CONTRAST TABLE PDP-R05E/WYVI, /WYVIXK, PDP-R05XE/WYVIXK, PDP-R05FE/WYVI and / WYVIXK are constructed the same except for the following: PDP-R05E/ PDP-R05E/ PDP-R05XE/ PDP-R05FE/ PDP-R05FE/ Mark Description WYVI WYVIXK WYVIXK WYVI WYVIXK TUNER BOARD Assy Not used Not used AWE1301 Not used...
2.4 FRONT PANEL SECTION Refer to below. Except PDP-R05FE For PDP-R05E and PDP-R05FE For PDP-R05XE Please cut-off 2 portion Please cut-off 1 portion before assembly. before assembly. PDP-R05E...
Page 17
See Contrast table (2) Front Panel See Contrast table (2) Door Holder L AMR3414 Door Holder R AMR3415 (2) CONTRAST TABLE PDP-R05E/WYVI, /WYVIXK, PDP-R05XE/WYVIXK, PDP-R05FE/WYVI and / WYVIXK are constructed the same except for the following: PDP-R05E/ PDP-R05E/ PDP-R05XE/ PDP-R05FE/ PDP-R05FE/ Mark...
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM 3.1 BLOCK DIAGRAM 3.1.1 SIGNAL ROUTE PDP-R05XE,PDP-R05E,PDP-R05FE Block Diagram Data signal Antenna U7501 Analog Audio signal Control signal Analog Video signal Input AXF1133 RF signal Component signal Digital Video signal IC7501 Digital Audio signal...
I2C_tun SPDIF Converter [IC4003] SDRAM [IC3000] 128Mbit Audio L/R in Audio A/D [IC4008] SPDIF out OMEGA [IC2000] SDRAM AudioLPF [IC3003] opamp 128Mbit Video Buffer Transistor Analogue Audio out Flash [IC3002] Analogue Video out TxRx,controls CPLD [IC6000] Digital Video out PDP-R05E...
I I C8505 V+5V • Component SW and around it R8528 IC8506 V+5V R8531 • FE and around it V+3V IC8507 R8543 V+3_DR • TELE TEXT, memory, and SW Q8511 FET_SW V+2V IC8508 R8545 PSW1 • IF Ucom and around it PDP-R05E...
Page 29
Therefore, when replacing, be sure to use parts of identical designation. • : The power supply is shown with the marked box. 1/12 - 12/12 MR MAIN BOARD ASSY (PDP-R05E, : AWZ6944) PDP-R05XE : AWZ6990) (PDP-R05FE : AWZ6945) MDR ASSY (AWZ6948)
3.3 MR MAIN BOARD ASSY (1/12) 1/12 MR MAIN BOARD ASSY (PDP-R05E : AWZ6944) NOT USED (PDP-R05XE : AWZ6990) (PDP-R05FE : AWZ6945) ¶ GR BLOCK SIDE A 12/12 12/12 NOT USED 1/12 PDP-R05E...
Page 31
NOT USED 2/12-9/12, 11/12-12/12 SIDE A 2/12, 3/12 NOT USED 1/12 PDP-R05E...
3.4 MR MAIN BOARD ASSY (2/12) 2/12 MR MAIN BOARD ASSY (PDP-R05E : AWZ6944) ¶ MICHEL MAIN BLOCK (PDP-R05XE : AWZ6990) (PDP-R05FE : AWZ6945) 8/12, 10/12 4/12, 7/12, 8/12 MAIN Y/C SEP. CHROMA DEC. MAIN 1/12 2/12 PDP-R05E...
Page 33
4/12, 12/12 SIDE A SIDE A 3/12 SIDE A (EU : PDP-R05E, PDP-R05XE) (EUB : PDP-R05FE) SIDE A 4/12 SIDE A 12/12 SIDE A 12/12 SIDE A 3/12, 8/12, 12/12 12/12 3/12 3/12, 8/12, 9/12, 12/12 1/12, 3/12-12/12 3/12, 6/12,...
3.6 MR MAIN BOARD ASSY (4/12) 4/12 (PDP-R05E : AWZ6944) MR MAIN BOARD ASSY (PDP-R05XE : AWZ6990) ¶ AD MAIN BLOCK (PDP-R05FE : AWZ6945) (EU : PDP-R05E, PDP-R05XE) (EUB : PDP-R05FE) 12/12 8/12 SIDE A SIDE A Selector SIDE A...
Page 37
SIDE A 2/12, 7/12, 8/12 SIDE A 8/12 2/12, 7/12, 8/12 1/12-3/12, 5/12-12/12 Filter Filter 2/12, 12/12 Through Selector Conversion 8/12 SIDE A Component SIDE A 8/12 4/12 PDP-R05E...
3.7 MR MAIN BOARD ASSY (5/12) 5/12 (PDP-R05E : AWZ6944) MR MAIN BOARD ASSY (PDP-R05XE : AWZ6990) ¶ AD SUB BLOCK (PDP-R05FE : AWZ6945) 12/12 SIDE A SIDE A SIDE A SIDE A 3/12, 5/12, 7/12, 9/12 12/12 3/12, 7/12, 9/12...
Page 39
(EU : PDP-R05E, PDP-R05XE) (EUB : PDP-R05FE) 3/12, 7/12, 9/12 3/12, 7/12, SIDE A 9/12 9/12 1/12-4/12, 6/12-12/12 Conversion Selector Filter Through Filter 3/12, 12/12 Through 3/12, 12/12 SIDE A 9/12 Component 5/12 PDP-R05E...
3.14 MR MAIN BOARD ASSY (12/12) ¶ REGULATOR BLOCK CN8651 SIDE A CN8652 2/12 4/12 3/12 5/12 4/12 5/12 6/12, Connector for JTAG/SDI 4/12, 5/12 12/12 10/12 11/12 SIDE A CN8654 6/12 11/12 1/12-11/12 6/12 SIDE A 12/12 6/12 PDP-R05E...
3.20 AV BOARD ASSY (6/9) AV BOARD ASSY (PDP-R05E : AWZ6946) (PDP-R05XE : AWZ6986) (PDP-R05FE : AWZ6947) ¶ UCOM BLOCK SIDE A SIDE B 1/9-5/9, 7/9, 8/9 PDP-R05E...
Page 65
Writing Connector SIDE A SIDE B SIDE B SIDE A SIDE B PDP-R05E...
30PRA60-FC S355 HT3.15A K2543 CR89 SRW28EC-T76V012 NEUTRAL MD1CUR22J K2862 S355 CR27 AC SW ASSY (AWZ6920) T P 7 3 8 2 T P 7 3 8 3 CN 7 4 5 6 LIVE AC IN NEUTRAL AC INLET (AKP1272) PDP-R05E...
Field effect SIDE B P.C.Board Chip Part transistor Resistor array 3-terminal regulator 4.1 SW and MDR ASSYS SIDE A SIDE B MDR ASSY MDR ASSY Q9302 Q9301 Q9303 IC9301 CN7402 IC9302 (ANP2088-B) (ANP2088-B) SW ASSY SW ASSY (ANP2093-A) (ANP2093-A) PDP-R05E...
4.3 AV BOARD and SR ASSY SIDE A AV BOARD ASSY CN7454 CN4000 CN7455 CN8652 CN8662 CN8654 (ANP2088-B) CN7451 CN9651 PC CARD MODULE CP51 PC CARD MODULE PDP-R05E...
Page 105
SIDE A 4000 SR ASSY (ANP2088-B) CN9452 CN6002 CN6001 CN9502 PDP-R05E...
Page 106
SIDE B AV BOARD ASSY SR ASSY (ANP2088-B) PDP-R05E...
4.4 FRONT and LED ASSY SIDE A SIDE A FRONT ASSY LED ASSY IC9602 IC9601 Q9506 Q9507 Q9508 Q9651 Q9654 CN8656 Q9653 (ANP2083-A) Q9502 Q9501 IC9501 CN8653 Q9505 Q9501 IC9502 Q9504 Q9503 (ANP2083-A) PDP-R05E...
Page 109
SIDE B SIDE B LED ASSY FRONT ASSY (ANP2083-A) (ANP2083-A) PDP-R05E...
Ex.2 When there are 3 effective digits (such as in high precision metal film resistors). 5.62k Ω 562 x 10 5621 RN1/4PC 5 6 2 1 • LIST OF ASSEMBLIES PDP-R05E/ PDP-R05E/ PRO-R05XE/ PDP-R05FE/ PDP-R05FE/ Mark Symbol and Description WYVI...
PC CARD Unit replacement is allowed. The assembly must be replaced as a unit, and no part TUNER Board Assy replacement is allowed. Other assemblies No adjustment required Adjustment items 1 AFC Adjustment 2 RF-AGC Adjustment 3 Video Level Adjustment PDP-R05E...
3-10 seconds. Then within 3 seconds after the key is released, use the SET key on the remote control unit to set to RS-232C (the baud rate last selected is chosen) or the HOME MENU key to set to SR+. PDP-R05E...
6.4 ADJUSTMENT ITEMS If readjustment is necessary because of adjustment error at shipment, perform adjustments as shown below. ¶ Adjustment Points AV BOARD ASSY Rear side SIDE A SIDE A SIDE B TP7506 TP7502 VR7504 L7504 TP7501 VR7502 VR7503 PDP-R05E...
The TRAP switch is disabled while the unit is turned off. When performing internal diagnosis of the PDP, fix the switch to the OFF position using adhesive tape before turning on the unit. After servicing, be sure to remove the adhesive tape. TRAP switch PDP-R05E...
About connections • Connect the SR OUT connector of a Pioneer product having that connector (a DVD in the following example) and the SR IN connector of the Media Receiver, using the SR cable. As the remote control sensor is not provided with the Media Receiver, this connection is required for using the remote control unit if the panel is not available.
Function: TV Numeric keys Function: TV (previously selected channel number is selected) POWER Power OFF Turning the power off FACTORY Factory OFF Turning Service Factory mode off MENU Menu ON Turning Service Factory mode off and Menu mode on PDP-R05E...
Page 140
3.AUTO PRESET 4. EDIT WRITE MODE 5. CH PRESET MUTE MUTE 3 INDIVIDUAL mode 1. CVY GAIN 2. RY GAIN 3. GY GAIN 4. BY GAIN MUTE 4 COMMON ADJ. mode 1. RGB 1 2. PANEL 1 3. PANEL 2 PDP-R05E...
Page 141
On-Screen Display NTSC Composite input/ S-connector input SECAM 4.43NTSC BLACK/WHITE Y / CB / CR Y / PB / PR Digital video signal 4 Option (Destination, etc.) Options On-Screen Display Advanced : PDP-R05XE Standard : PDP-R05E Basic : PDP-R05FE PDP-R05E...
Page 143
(?: available, ×: not available) 3rd Character Description on GUI VIDEO Remarks × DOT BY DOT 4 : 3 FULL (FULL1) × ZOOM × CINEMA × WIDE Indude WIDE-HD × FULL 14 : 9 × CINEMA 14 : 9 FULL2 HDTV1035i × OVERSCAN PDP-R05E...
Page 144
P A S SWO R 1 2 3 4 Device Name Display Version Display Remarks DTV Software Version 4 character PDP-R05XE only PC Card Software Version CARD 8 character Except PDP-R05FE Teletext ucom Software Version TEXT 60 character USER Password PASSWORD 4 character PDP-R05E...
Page 145
Remarks (MAIN) Abnormality in IC 4 communication Subcategories exist. Abnormality in module microcomputer IIC MD-IIC (EROM4K : IC5206, communication EROM2K : IC402, VOLIC : IC3502) Abnormality in RST2 RST2 Abnormality in panel temperature TEMP1 Short-circuiting of the speakers AUDIO PDP-R05E...
Page 146
The value of the Fan output is displayed. At shipment, the output is controlled in 2 steps, and the value for strong output is set to about 131, and the value for weak output is set to about 93. PDP-R05E...
Page 147
V D 1 – 0 1 3 – N T V – S T 1 C U N T E R 0 0 0 0 0 0 0 0 T I M E S The cumulative number of times the panel was turned on is displayed. PDP-R05E...
Page 148
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 N F O R M A T I O N V D 1 – 0 1 3 – N T V – S T 1 E E P R OM Y E S PDP-R05E...
Page 149
– 3 C : 0 0 – 0 8 : 0 0 – 3 D : 0 0 – 0 C : 0 0 – 0 D : 0 0 – 0 E : 0 0 For technical discussion PDP-R05E...
Page 150
Change the power supply voltage for the digital tuner antenna. This setting item is not recorded in the memory. Return in the user setting when finish the factory mode. 2.3 AUTO PRESET Make the frequency range narrow for shipment check, and auto preset. PDP-R05E...
Page 151
RY GAIN <=> Input GAIN adjustment of component (Cr)/RGB(R) series 000-255 AD 0x08B D7-D0 GY GAIN <=> Input AIN adjustment of component (Y)/RGB(G) series 000-255 AD 0x08B D7-D0 BY GAIN <=> Input GAIN adjustmentof component (Cb)/RGB(B) series 000-255 AD 0x08B D7-D0 PDP-R05E...
Page 152
SUB side AD/PLL input-R OFFSET adjustment 064-191 A/D(S) 0x0B D7-D1 AD SUB G OFFSET <=> SUB side AD/PLL input-G OFFSET adjustment 064-191 A/D(S) 0x0C D7-D1 AD SUB B OFFSET <=> SUB side AD/PLL input-B OFFSET adjustment 064-191 A/D(S) 0x0D D7-D1 PDP-R05E...
Page 154
• Frequency selection while the mask is displayed Corresponding No. Function/Display Content RS-232C Command Video 50-Hz sequence V60 (initial value) Video 60-Hz sequence PC 60-Hz sequence PC 70-Hz sequence Video 72-Hz sequence Video 75-Hz sequence PDP-R05E...
Page 155
9600-232C To set to RS-232C (9600 BPS) 19200-232C To set to RS-232C (19200 BPS) 38400-232C To set to RS-232C (38400 BPS) Tips: How to change the SR+/RS-232C setting without entering Service Factory mode Refer to "6.3 USING RS-232C COMMANDS". PDP-R05E...
Obtaining the PANEL REVISE data Obtaining the PULSE METER data Obtaining the PANEL W/B data Obtaining the version data for each device Obtaining data on various operations Obtaining the any version Obtaining shutdown information Adjusting side mask G GY GAIN PDP-R05E...
Page 157
Command Operation Remarks INC*** Selection of the tuner for terrestrial digital signals PDP-R05XE only Selection of SD card/PCMCIA card PDP-R05XE and PDP-R05E only INPS01 Input selection: Input 1 INPS02 Input selection: Input 2 INPS03 Input selection: Input 3 INPS04 Input selection: Input 4...
Page 158
U1 leading-edge pulse of X-SUS U2 leading-edge pulse of X-SUS D1 trailing-edge pulse of Y-SUS D2 trailing-edge pulse of Y-SUS D3 trailing-edge pulse of Y-SUS D4 trailing-edge pulse of Y-SUS U1 leading-edge pulse of Y-SUS U2 leading-edge pulse of Y-SUS PDP-R05E...
GPC: Returning the cumulative number of times the power to the PDP was turned on Data Size Order Power-on counter 8 bytes • Commands for clearing the logs Corresponding Parameter RS-232C Command PD INFO SD INFO NG INFO HOUR METER MR HOUR METER (Only for the system model) PULSE METER P ON COUNTER PDP-R05E...
Page 160
Data on temperature for the eighth latest PD (TEMP1) 3 bytes • Details on "1st/2nd PD" data Data Power-down Point No power-down Not used (for MR-POWER) P-POWER SCAN SCN-5V Y-DRIVE Y-DCDC Y-SUS ADRS X-DRIVE X-DCDC X-SUS DIG-DCDC Power-down point not identified PDP-R05E...
Page 161
Panel having abnormally high temperature Audio failure (short-circuiting of the speakers) 6 - F Spares • Data on the shutdown subcategories for the module microcomputer IIC Data Cause of Shutdown No subcategory EEPROM (4k) (IC5206) EEPROM (2k) (IC4002) Volume IC (IC3502) PDP-R05E...
Page 162
Cause of Shutdown No subcategory (DTV for North America) Communication failure of the DTV microcomputer (PS/RST) DTV NG (DEVICE) DTV microcomputer (CMD) DTV microcomputer communication (RETRY) PC CARD Communication NG (CD-COM) PC CARD Mdule (CD-DEV) PC CARD Reset NG (CD-RST) PDP-R05E...
Page 163
GS6: Returning information of the Flash Device Data Size Order Display Information 3 bytes Version of the DTB (PDP-R05XE only) 4 bytes Version of the PC Card (Except PDP-R05FE) 8 bytes Version of the Text 60 bytes User Passward 4 bytes PDP-R05E...
Finishing troubleshooting • Diagnosis points MR MAIN BOARD ASSY AV BOARD ASSY • For check the communication with the microcomputer, refer to the section 6.7 SERVICE FACTORY MODE. • The encircled numbers denote measuring point in the Waveforms for Troubleshooting. PDP-R05E...
Page 165
IC8002. Check around IC8002 and Is a signal output from check the communications IC8002? between IC8002 and the (41) microcomputer. Has the signal arrived at Check the communication TP7705? between IC8002 and TP7705. Check around the jack. PDP-R05E...
Page 166
IC on the found to have a failure in MR MAIN BOARD Assy and communication and the the microcomputer normal? microcomputer. Has the symptom been settled when the MR MAIN The panel is defective. BOARD Assy is replaced? Finishing troubleshooting PDP-R05E...
Page 167
Check around the jack. IC8008? Check around IC8008. (7) (10) Is a signal output from IC8007? Check around IC8007. (1) (7) Is the flexible cable between Reconnect the flexible cable CN8653 and CN9502 then check again. correctly connected? Check around the jack. PDP-R05E...
Page 168
Is a signal input to IC8002? Check the communications (62), (64) between IC7502 and Is a signal input to IC8002? Check the communications IC8002. between the jack and IC8002. Check around IC8002 and check the communications between IC8002 and the microcomputer. PDP-R05E...
Page 169
Has the symptom been settled when the system The panel is defective. Is a signal output from cable is replaced? IC8007? Check around IC8007. (1), (7) Has the signal arrived at Finishing troubleshooting TP7710? Check around Q7761. Check around the jack. PDP-R05E...
Page 170
Finishing troubleshooting DTB is defective. Is an animation output by Is a signal output from RGB, Replace DTB. Monitor OUT? CVBS and Y/C of CN4000?. Check the communication between CN4000 and CN8665, between CN8665 and IC8002, between CN8665 and IC8005. PDP-R05E...
Page 171
Does a sound except DTB Is a signal output from LA_IN Check the communication output it? and RA IN of CN4000?. between CN4000 and CN8665, between CN8665 and IC8003. DTB is defective. Finishing troubleshooting Replace DTB. DTB is defective. Replace DTB. PDP-R05E...
Remove the front panel section. Please remove it after pulling it in a rear direction because bonnet top and metal bonnet bottom are hard to reduce. Metal bonnet top Rear view Metal bonnet bottom Metal bonnet top Front panel section Metal bonnet bottom PDP-R05E...
Page 178
Remove the PC board TUNER. Top can Rear view Remove the two screws. Disconnect the two connectors. Disconnect the two flexible cables. Remove the TUNER BOARD Assy. Bottom can Disconnect the one connector. PC board TUNER TUNER BOARD Assy ×2 PDP-R05E...
Page 179
PCB Location MDR Assy POWER SUPPLY Unit MR MAIN BOARD Assy LED Assy SW Assy AV BOARD Assy SR Assy PC Card Module FRONT Assy PDP-R05E...
FAN_NG2 (H_act) (DIGITAL TUNER FAN) Specifications for port monitoring Port Name SD/PD Indication Assigned Pin Active FAN_NG 1 Shutdown with H FAN_NG 2 Shutdown with H TEMP2 Abnormally high Shutdown when the temperature in the value exceeds the predetermined value PDP-R05E...
Page 181
TRAP_SW Circuit diagram TRAP_SW MR MAIN BOARD Assy V+3V_COM TRAP_SW MAIN_UCOM PULL_D Specifications for port monitoring Port Name SD/PD Indication Assigned Pin Active TRAP_SW Modification tried OFF with L PDP-R05E...
5 : MOD microcomputer controls the relay of PDP power supply MOD, and activate the power supply of PDP side. 6 : Main microcomputer controls the relay of MR power supply MOD, and activate the power supply of MR side. PDP-R05E...
Page 186
MIDSCV Internal middle scale voltage bias CLAMP Clamp input (External clamp signal) − Analog power supply (3.3V) − Ground − Ground − Analog power supply (3.3V) BAIN Analog input for converter B − Ground − Analog power supply (3.3V) PDP-R05E...
Page 187
RED 5 Converter Red output RED 4 Converter Red output RED 3 Converter Red output RED 2 Converter Red output RED 1 Converter Red output RED 0 Converter Red output − Power supply (3.3V) − Power supply (3.3V) − Ground PDP-R05E...
Page 189
Analog 5V supply Analog RINA or YINA signal input. Sync signal is input on SYNCIN pin. GSR1 ROUT/YOUT output buffer gain set input Analog RINB or YINB signal input. Sync signal is input on SYNCIN pin. − (NC) No connection PDP-R05E...
Page 190
Block Diagram HSCTL POLH H SYNC DET. C / HSYNC IN EXIH VIDEO IN POLV SYNC SEPA. VSEPA EXIV HOR. SYNC CONTROL V SYNC SEPA. VSYNC IN CVPOL HDRV V SYNC DET. CVEXI CLAMP CPSEL VDRV CLAMP PULSE GEN. CPWID PDP-R05E...
Page 191
Indecates whether the vertical synchronization signal exists. Vertical polarity output POLV Indicates the polarity of the vertical synchronization signal. Horizontal existence output EXIH Indicates whether the horizontal synchronization signal exists. Horizontal polarity output POLH Indicates the polarity of the horizontal synchronization signal. PDP-R05E...
Page 192
83,84 BOARD RXC± MASK CONTROL PANEL LINK SPDIF 86,87 RX0± TMDS CONTROL SIGNALS DIGITAL CORE VIDEO 91,92 RX1± COLOR HSYNC CONTROL SIGNALS RX2± 96,97 SPACE VSYNC CONVERTER ODCK UP/DOWN SAMPLING 36-39,42-44,48-55, Q[23-0] 58-63,68-70 AnGY VIDEO AnRPr AnBPb RSET COMP PDP-R05E...
Page 193
OVCC Output bus power supply (3.3V) RX2+ TMDS data input − 24-bit output pixel data bus AGND Analog ground − 24-bit output pixel data bus Digital ground − 24-bit output pixel data bus 100 VCC Digital power supply (3.3V) PDP-R05E...
Page 194
34 DQ18 Burst 36 DQ19 Counter 37 DQ20 39 DQ21 40 DQ22 42 DQ23 45 DQ24 47 DQ25 48 DQ26 50 DQ27 CAS Latency Pipe Line Control Mode Register Data Out Control 51 DQ28 53 DQ29 54 DQ30 56 DQ31 PDP-R05E...
Page 195
I/O Data input/output DQ13 I/O Data input/output DQ22 I/O Data input/output DQ14 I/O Data input/output − − VDDQ Power supply for output buffer VSSQ Ground for output buffer DQ23 I/O Data input/output DQ15 I/O Data input/output − − Power supply Ground PDP-R05E...
Page 196
Write enable DW/W 16 bit, 32 bit mode switch Write protect Acceleration − 17, 27, 33, 64, 74, 79 V Ground − 12, 18, 28, 58, 63, 73 V Power supply 1-5, 41-50, − N.C. No connection 83-85, 89, 90 PDP-R05E...
Page 197
CONFIGURATION ENGINE EEPROM LOGIC BLOCK HSYNC VSYNC EXT_SWING IDCK+ IDVK- 21,22 TXC± PANEL LINK 24,25 TX0± ENCRYPTED TMDS 36-47, DATA CLEAR DATA 27,28 TX1± DIGITAL CORE 50-55, MASK DATA CAPTURE D[23-0] 58-63 LOGIC BLOCK 30,31 TX2± CONTROL SIGNALS CTL3 PDP-R05E...
Page 198
24-bit pixel bus input 24-bit pixel bus input 24-bit pixel bus input 24-bit pixel bus input 24-bit pixel bus input 24-bit pixel bus input 24-bit pixel bus input 24-bit pixel bus input 24-bit pixel bus input 24-bit pixel bus input PDP-R05E...
Page 199
24-bit / 12-bit pixel bus input 24-bit / 12-bit pixel bus input 24-bit / 12-bit pixel bus input 24-bit / 12-bit pixel bus input 24-bit / 12-bit pixel bus input 24-bit / 12-bit pixel bus input − Digital ground PDP-R05E...
Page 201
4 : 3 letter-box signal at 1.3 V or more to 2.5 V or less S2-3 16 : 9 picture squeezed signal at 2.5 V or more S2-4 This pin is pulled down to GND by a 100 k ohm resistor, so the 4 : 3 video signal is selected when open. PDP-R05E...
Page 202
Connects trap circuit for subcarrier. TRAP2 Audio signal output mute. Mute OFF at 1.5 V or less − MUTE Mute ON at 2.5 V or more Mute OFF when open. Internal reference bias (VCC/2). − BIAS Connect to GND via a capacitor. PDP-R05E...
Page 204
Volume capacitor MAIN AHVSS Analog ground AGNDC Analog reference voltage high-voltage part Not connected Not connected Not connected SC1_IN_L SCRAT 1 input, left SC1_IN_R SCRAT 1 input, right VREFTOP Reference voltage IF A/D converter MONO_IN Mono input AVSS Analog ground PDP-R05E...
Page 207
D-Cache Data XTAL (6 MHz) X-BUS Instr./Data 36 nodes (8 ext.) XRAM 2 Kbyte GPT1 OCDS GPT2 Channel USART Watchdog D-Sync 7-bit JTAG FIFO 3 x 6 Bit Port 5 Port 3 Port 2 Port 4 Port 6 UEB10716 PDP-R05E...
Page 208
O External memory read strobe for ROM. RD is activated for every external instruction or data read access. 47 RD − 48 UDQM O Write disable for high byte − 49 LDQM O Write disable for low byte − 50 WR O Memory write strobe PDP-R05E...
Page 209
I/O General purpose I/O port/Field signal of field detection 98 P6.3 SCL1 I/O General purpose I/O port/I2C bus clock line 1 99 P6.4 SDA1 I/O General purpose I/O port/I2C bus data line 1 − 100 P6.5 I/O General purpose I/O port PDP-R05E...
General purpose Input port/Analog input for A/D-converter − 128 TMODE Test mode pin 7.4 CLEANING Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools: Position to be cleaned Cleaning tools Fans Cleaning paper : GED-008 PDP-R05E...
INPUT 4 terminal (S-VIDEO) INPUT 4 terminal (VIDEO) INPUT 4 terminals (AUDIO) PC INPUT terminal (AUDIO) PDP-505XDE/435XDE only 10 PC INPUT terminal (ANALOG RGB) PDP-505XDE/435XDE only 11 PC CARD slot PDP-505XDE/435XDE only 12 PC CARD EJECT button PDP-505XDE/435XDE only PDP-R05E...
Page 212
(COMPONENT VIDEO: Y, P 8 DIGITAL OUT terminal (OPTICAL) 19 INPUT 3 terminal (HDMI) PDP-505XDE/435XDE only 20 SYSTEM CABLE terminal (WHITE) 9 COMMON INTERFACE slot 21 SYSTEM CABLE terminal (BLACK) PDP-505XDE/435XDE only • For a CA Module with a smart card PDP-R05E...
Page 213
TELETEXT mode: Stops updating Teletext pages. Press again to release the hold mode. TELETEXT mode: Selects a page. 8 TV/DTV (PDP-505XDE/435XDE only) • When using the remote control unit, point it at the Switches between the TV and DTV input mode. Plasma Display. PDP-R05E...