Advertisement
Quick Links
Lossnay Remote Controller
PZ-62DR-E
Installation Manual
This installation manual describes how to install the Lossnay Remote Controller.
Please be sure to read this installation manual before proceeding with the installation.
Failure to follow the instructions may result in equipment damage.
For information on how to wire and install the Lossnay units, refer to the Lossnay unit Installation Manual.
After the installation, hand over this manual to users.
1. Safety Precautions
● Thoroughly read the following safety precautions prior to installation.
● Observe these precautions carefully to ensure safety.
WARNING
Indicates a risk of death or serious injury.
CAUTION
Indicates a risk of serious injury or structural damage.
● After reading this manual, pass it on to the end user to retain for future reference.
● Keep this manual for future reference and refer to it as necessary. This manual should be made available to those who repair or relocate
the controller. Make sure that the manual is passed on to any future users.
General precautions
WARNING
Do not install the unit in a place where large amounts of oil, steam,
organic solvents, or corrosive gases, such as sulfuric gas, are present
or where acidic/alkaline solutions or sprays are used frequently. These
substances can compromise the performance of the unit or cause
certain components of the unit to corrode, which can result in electric
shock, malfunctions, smoke, or fire.
To reduce the risk of shorting, current leakage, electric shock,
malfunctions, smoke, or fire, do not wash the controller with water
or any other liquid.
To reduce the risk of electric shock, malfunctions, smoke or fire, do
not operate the switches/buttons or touch other electrical parts with
wet hands.
CAUTION
To reduce the risk of fire or explosion, do not place flammable
materials or use flammable sprays around the controller.
To reduce the risk of damage to the controller, do not directly spray
insecticide or other flammable sprays on the controller.
To reduce the risk of electric shock or malfunctions, do not touch
the display or buttons with a pointy or sharp object.
All electric work must be performed by qualified personnel.
For distribution to dealers and contractors
To reduce the risk of injury or electric shock, before spraying a
chemical around the controller, stop the operation and cover the
controller.
To reduce the risk of injury or electric shock, stop the operation and
switch off the power supply before cleaning, maintaining, or inspecting
the controller.
Properly install all required covers to keep moisture and dust out of the
controller. Dust accumulation and water can cause electric shock,
smoke, or fire.
To reduce the risk of injury, keep children away while installing,
inspecting, or repairing the controller.
To reduce the risk of injury and electric shock, avoid contact with
sharp edges of certain parts.
To avoid injury from broken glass, do not apply excessive force on the
glass parts.
To reduce the risk of injury, wear protective gear when working on the
controller.
Eng-1
English
2105875H17001
Advertisement
Related Manuals for Mitsubishi Electric PZ-62DR-E
Summary of Contents for Mitsubishi Electric PZ-62DR-E
- Page 1 English 2105875H17001 Lossnay Remote Controller PZ-62DR-E Installation Manual For distribution to dealers and contractors This installation manual describes how to install the Lossnay Remote Controller. Please be sure to read this installation manual before proceeding with the installation. Failure to follow the instructions may result in equipment damage.
- Page 2 This controller is designed for exclusive use with the Lossnay by To avoid damage to the controller, do not overtighten the screws. Mitsubishi Electric. The use of this controller for other systems or for other purposes may cause malfunctions. Use a flat-head screwdriver with a blade width of 4-7 mm (5/32-9/ 32 inch).
- Page 3 To avoid damage to the controller, provide protection against static Do not install the controller on the control panel door. electricity. Vibrations or shocks to the controller may damage the controller or cause the controller to fall. Do not use solderless terminals to connect cables to the terminal block.
-
Page 4: Selecting An Installation Site
3. Field-supplied parts/Required tools (1) Field-supplied parts The following parts are field-supplied parts. . y t c t i Not required for direct wall installation l l o l l a y l l Remote controller cable Necessary (Use a 0.3 mm² (AWG22) 2-core sheathed cable.) (2) Field-supplied tools ●... - Page 5 5. Installation/Wiring work (1) Installation work Controller can be installed either in the switch box or directly on the wall. Perform the installation properly according to the method. Conduit Wall 1 Drill a hole in the wall. tube Installation using a switch box Locknut ●...
- Page 6 5 Install the bottom case. Installation using a switch box ● Secure at least two corners of the switch box with screws. Direct wall installation ● Thread the cable through the groove. ● Secure at least two corners of the remote controller with screws. ●...
- Page 7 8 Route the wire to the top case. Important Hold the cables in place with clamps to prevent undue force from being applied to the terminal block and causing cable breakage. Clamp Insert the wire. 9 Install the front cover and top case on the bottom case. Two mounting tabs are at the top of the top case.
- Page 8 3 Installing the cover and top case Two mounting tabs are at the top of the top case. Wall Hook those two tabs onto the bottom case, and click the top case into place. Install the cover on the top case in the same way as with the top case.
- Page 9 7. Remote controller button functions (5) Backlit LCD (7) Function buttons F1, F2, F3, and F4 from the left (6) ON/OFF lamp (1) ON/OFF button (3) RETURN button (4) MENU button (2) SELECT button (1) ON/OFF button Pressing the button will bring up the Main menu as Press to turn ON/OFF the Lossnay unit.
-
Page 10: Turning On The Power
8. Turning on the power Make sure that the remote controller is properly installed according to the instructions in the Installation Manual and that the Lossnay unit installation has been completed before turning on the power. (1) When the power is turned on, the following screen will appear. Note: •... - Page 11 9. Initial setting menu (Remote controller settings) <Administrator password is required.> From the Main display, select Commissioning menu>Initial setting, and make the remote controller settings on the screen that appears. Press the button to move the Initial setting menu Initial setting menu cursor.
- Page 12 (4) Remote controller display details setting Make the settings for the remote-controller-related items as necessary. Display details Clock No 24h Press the button to save the changes. Temperature Sensor value / No Select: Cursor Change [1] Clock display [Button operation] Clock display Clock •...
- Page 13 (5) Administrator password setting [Button operation] [1] To enter the current Administrator password (4 numerical digits), move the cursor to the digit you Administrator password want to change with the button, and set each number (0 through 9) with the Enter administrator password button.
-
Page 14: Service Menu
10. Service menu <Administrator password is required.> Select “Service menu” from the Main menu > Commissioning and press the button. Commissioning menu The service menu will appear. Initial setting Airflow Auto bypass External input Service Main menu: Cursor Page (1) Input maintenance Info. Service menu Select “Input maintenance Info.”...