Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instruction
manual
1. SAFETY
WARNING! DO NOT use the torque wrench if damaged or thought to be faulty.
‰
Ensure all workshop safety rules, regulations and conditions are complied with when using the torque wrench.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the working area.
9
Avoid over-torquing the wrench (110% of maximum torque range) as this will cause loss of accuracy.
9
Keep the wrench away from magnets.
9
In operation when you hear the continuous tone, stop pulling immediately especially in case the target torque/ angle is low.
9
Ensure all sockets, extensions and drivers are rated correctly and are of flawless construction. Avoid using adaptors and extensions for
9
best accuracy.
DO NOT use the torque wrench if the batteries are low, torque accuracy will be affected.
8
DO NOT use the wrench as a hammer or similar.
8
DO NOT use on live electrical circuits the plastic handle is not insulated.
8
DO NOT subject the wrench to excessive force or shocks.
8
DO NOT drop, throw, or violently shake the wrench.
8
DO NOT operate the wrench in damp conditions.
8
DO NOT operate the wrench in dusty conditions.
8
DO NOT push on the LCD panel.
8
DO NOT use wrench until first instructed in its use by a qualified person.
8
DO NOT leave the wrench in a place exposed to excessive heat, humidity or direct sunlight.
8
DO NOT use organic solvents such as alcohol or thinners to clean the wrench.
8
After use, turn the wrench off, clean with a soft dry cloth, place torque wrench in its storage case, and store in a safe, dry, childproof
8
location.
Remove the batteries if the torque wrench is not to be used for a long time, to prevent damage from leaking.
9
2. INTRODUCTION
Rugged and resilient digital torque wrench suitable for workshop and factory use. LCD read-out with LED, vibration and audible alarms
to indicate achieved and target torque levels. Features angle mode, eliminating the need for angle gauges and protractors providing an
accurate and fast way to measure torque plus angle tightening sequences. Will also accumulate angle measurement when
multiple turns are required, ideal for use where access is limited. Selectable track or peak modes and up to five user preset memories
available. Read-outs in Nm, lb.in, lb.ft, kgf.m or degrees. Reversible Chrome Vanadium 72-tooth ratchet allows torque reading in either
direction. Accurate to ±2% of wrench's stated capacity. Supplied with test certificate and storage case.
3.
SPECIFICATION
Model No: ......................................................... STW310
Angle Range: ...................................................... 5-360°
Battery: ............................................. 4 x AAA (supplied)
Drive: .................................................................. 1/2"Sq
Length: ............................................................... 675mm
Range: ..................................... 30-340Nm (22-250 lb.ft)
4.
CALIBRATION
We recommend to ensure continued accuracy the calibration of the wrench should be checked annually,beginning one year after the
first time of use. Calibration should also be checked after any impact,
over-torquing or other misuse. Contact your Sealey Stockist to arrange recalibration.
© Jack Sealey Limited
1/2"SQ DRIVE DIGITAL TORQUE WRENCH WITH
ANGLE FUNCTION 30-340Nm
STW310
MODEL NO:
Original Language Version
STW310 Issue:1 22/02/23
Advertisement
Related Manuals for Sealey STW310
Summary of Contents for Sealey STW310
- Page 1 STW310 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 (Peak) mode or back to (Track) mode. 5.4.2. During the “Peak” mode, the maximum value reached will be saved additionally and the value is shown on the display for approx. 2 seconds. After that, this value is flashing then you keep going for the next application or press button to zero then keep going for the next application. Original Language Version STW310 Issue:1 22/02/23 © Jack Sealey Limited...
- Page 3 ANGLE measuring, will be shown on the screen. Hold the wrench still and stable, the wrench will self-test a few seconds, and show target angle and display 0°. © Jack Sealey Limited Original Language Version STW310 Issue:1 22/02/23...
- Page 4 Remove the batteries. Dispose of according to local government guidelines. Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.