Table of Contents
Advertisement
Introduction
The 104E colour monitor displays sharp and brilliant images of text and
graphics with a maximum resolution up to 1024x768 pixels. It is optimal
for Windows, spread sheets, and any other application.
This monitor automatically scans horizontal frequencies from 30KHz to
54KHz, and ver tical frequencies from 50Hz to 120Hz. With
microprocessor based digital controlled circuit, the monitor can
automatically adjust itself to the video card's scanning frequency and
displays an image with precise parameters you desire. The wide range
of scanning frequency supports variety of operating platforms, such as
IBM PC and compatibles, including Intel based platforms such as 386,
486, Pentium and Pentium II.
Feature Highlights
•
Global Styling demonstrates a soft & smart image.
•
Digital Control feature provides user-friendliness and ease-of-use
when operating the monitor.
•
Anti-Glare screen coating eliminate any bad effects caused by the
screen surface such as reflection of the room lights.
•
85Hz refresh rate:
The maximum display resolution is 1024 x 768 pixels non-interlaced
mode. The recommanded optimum resolution up to 800 x 600 pixels
non-interlaced by maximum 85Hz refresh rate.
•
DDC1/DDC2B allows communication between the monitor and PC
system for optimal video configuration.
E
N
1
Advertisement
Table of Contents
Related Manuals for Philips 104E
Summary of Contents for Philips 104E
-
Page 1: English Introduction
Introduction The 104E colour monitor displays sharp and brilliant images of text and graphics with a maximum resolution up to 1024x768 pixels. It is optimal for Windows, spread sheets, and any other application. This monitor automatically scans horizontal frequencies from 30KHz to 54KHz, and ver tical frequencies from 50Hz to 120Hz. - Page 2 Note: If you experienced your monitor display is changing from color to mono, it's possible that you are using a non-VESA-DDC-standard video card. Please consult with your local PCEC dealer for more information. NERGY TAR is a s an NERGY...
-
Page 3: Safety Precautions And Maintenance
Safety precautions and maintenance Disconnect the monitor from the mains supply if the monitor is not to be used for an extended period of time. Do not attempt to remove the back cover, as you will be exposed to a shock hazard. The back cover should only be removed by qualified service personnel. -
Page 4: Installation
When positioning this monitor, make sure that the mains plug and socket are easily accessible. Pedestal With the built-in pedestal you can tilt and / or swivel the monitor for a most comfortable viewing angle. To fit the pedestal, refer to the illustration on the inside front-cover of this manual. -
Page 5: Connection
Failure to do so may cause serious personal injury as well as permanent damage to your computer equipments. Intel Based platform: 386, 486, Pentium, or other compatibles: • Connect the monitor to the computer using the supplied interface cables. Monitor rear view 1) IBM PC connection... -
Page 6: Connection To The Mains
Connection to the mains Connecting to the mains This monitor is set to operate at a mains supply of 100-240 volts AC. If the mains voltage in your home is not between this, consult your dealer. Connect one end of the mains cord to the mains socket at the rear of monitor, and the other end to the mains supply. -
Page 7: Front Control Locations And Functions
Front Control locations and functions For an optimized adjustment of the picture following controls are available at the front. POWER. Press this knob, the green LED lights and the power is ON. Press this knob again, the green LED disappears and the power is OFF. - Page 8 H-Size : to adjust the horizontal amplitude of the image. H-Center : to adjust the horizontal position of the image. V-Size : to adjust the vertical amplitude of the image. V-Center : to adjust the vertical position of the image. Pincushion: to correct the barrel distortion of the image.
-
Page 9: Adjustment
Adjustment The monitor is pre-set with 7 modes for optimal display size and centering as indicated in the following table: Resolution Mode (dots x lines) Freq.(KHz) 720 x 400 640 x 480 VESA/85 640 x 480 VESA/75 800 x 600... - Page 10 Active Stand-by Blanked Suspend Blanked Blanked Note: The video will be blanked and the power LED color will change into following colors whenever the monitor goes into power management status. Green LED light Amber LED light Amber LED light This monitor is a computer equipped with DPMS.
-
Page 11: Technical Information
Technical information (I) General: Picture tube Screen area Recommended Display Area: 250 mm (H) x 188 mm (V) Maximum Display Area Line (Horizontal) frequency : 30 - 54 KHz (automatically) Raster (Vertical) frequency : 50 - 120 Hz (automatically) Mains voltage Power consumption Maximum dot rate Video input signal... - Page 12 (III) Pin assignment: (1) The 15-pin D-sub connector (male) of the signal cable (IBM systems): Pin No. Assignment Red video input Green video input Blue video input Identification output - Connected to pin 10 Ground Red video ground Green video ground Blue video ground Because of a policy of continuous product improvement, the above specifications are subject to change without notice.
-
Page 13: Table Of Contents
14E4220T Digital Auto Scan Colour Monitor Contents English Introduction Feature Highlights Safety precautions and maintenance Package End of life disposal Installation Connection Connection to the mains Front Control locations and functions ... 7 Adjustment Technical information ... 1 ... 1 ... - Page 14 OTHER LANGUAGE VERSIONS FRENCH(FRANÇAIS) Appendix English Information for Users in the U.S. Deutsch Français ... 13 FCC Declaration WARRANTY Hinweis / GS / ACHTUNG FCC Declaration ... A1 ... A2 ... A5 ... A3 ... A4...