Table of Contents
Related Manuals for Toro Power Clear 39921T
Summary of Contents for Toro Power Clear 39921T
- Page 1 Form No. 3461-705 Rev A 21in Power Clear ® Flex-Force Power System ™ 60V MAX Snowthrower Model No. 39921—Serial No. 400000000 and Up Model No. 39921T—Serial No. 400000000 and Up *3461-705* Register at www.Toro.com. Original Instructions (EN)
- Page 2 Whenever you need service, genuine Toro parts, or For assistance, please see additional information, contact an Authorized Service www.Toro.com/support Dealer or Toro Customer Service and have the model for instructional videos and serial numbers of your product ready. Figure 1...
- Page 3 Charge the battery pack with only the battery to reduce the risk of fire, electric shock, or injury, charger specified by Toro. A charger suitable for including the following: 1 type of battery pack may create a risk of fire when used with another battery pack.
- Page 4 Replace the battery pack with a genuine common sense when operating the machine. Toro battery pack only; using another type of Do not use the machine while ill, tired, or under battery pack may cause a fire or risk of injury.
- Page 5 SAVE THESE INSTRUCTIONS...
-
Page 6: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal145-8252 decal145-8251 145-8252 145-8251 decal137-2257 137-2257 1. Warning—read the Operator’s Manual. 3. - Page 7 decal137-9463 137-9463 1. The battery pack is charging. 2. The battery pack is fully charged. 3. The battery pack is over or under the appropriate temperature range. 4. Battery pack charging fault decal137-9462 137-9462 decal137-9461 137-9461 1. Battery charge status decal137-9454 137-9454 1.
- Page 8 decal114-9035 114-9035 1. Cutting/dismemberment hazard of hand, impeller; cutting/dismemberment hazard of foot, auger—do not place your hand in the chute; remove the key and read the Operator’s Manual before performing maintenance. decal147-1787 147-1787 1. The combined Ah rating of 2. Read the Operator's all installed batteries must Manual.
- Page 9 Setup Important: The battery pack is not fully charged when you purchase it. Before using the machine for the first time, refer to Charging the Battery Pack (page 14). Mounting the Battery Charger (Optional) No Parts Required Procedure If desired, mount the battery charger securely on a wall using the wall-mount key holes on the back of the charger.
-
Page 10: Unfolding The Handle
Unfolding the Handle Parts needed for this procedure: Handle lock Handle knob Procedure g389401 Installing the Discharge Chute Parts needed for this procedure: Discharge chute assembly Hex washer head screw Chute handle Procedure g291515... -
Page 11: Product Overview
Contact your Authorized Service Dealer or authorized Toro distributor or go to www.Toro.com for a list of all approved attachments and accessories. To ensure optimum performance and continued safety... -
Page 12: Operation
Starting the Machine Operation Ensure that the battery pack (or battery packs) are installed in the machine; refer to Installing Installing the Battery the Battery Pack(s) (page 12). Pack(s) Insert the electric-start button into the electric starter (A of Figure Important: Use a battery pack only in Squeeze the bail and hold it to the handle (B... -
Page 13: Activating Eco Mode
Activating ECO Mode Removing the Battery Pack(s) from the Machine Using ECO mode may extend battery life by reducing rotor speed; use ECO mode whenever you are Lift up the battery-compartment lid. moving snow a short distance. Activate ECO mode using the ECO switch as shown in Figure Press the battery pack-latch to release the... -
Page 14: Charging The Battery Pack
Charging the Battery Pack To remove the battery pack, slide the battery backward out of the charger. Important: The battery pack is not fully charged Refer to the following table to interpret the LED when you purchase it. Before using the tool for indicator light on the battery charger. -
Page 15: Adjusting The Discharge Chute And Chute Deflector
Adjusting the Discharge Clearing a Clogged Chute and Chute Deflector Discharge Chute To adjust the discharge chute, move the chute handle. If the machine is running but there is no snow coming out of the discharge chute, the discharge chute may To adjust the chute deflector (and therefore the height be clogged. -
Page 16: Maintenance
Maintenance Stop the machine, remove the electric-start button, remove the battery pack from the machine, and wait for all movement to stop before adjusting, servicing, cleaning, or storing the machine. Inspecting the Rotor Blades Service Interval: Yearly—Inspect the rotor blades and have an Authorized Service Dealer replace the rotor blades and scraper if necessary. - Page 17 Call2Recycle seal, please contact your local municipality for more information on how to responsibly recycle the battery. If you are located outside of the US and Canada, please contact your authorized Toro distributor.
-
Page 18: Troubleshooting
5. The auger/impeller drive belt is loose 5. Install and/or adjust the auger/impeller or is off the pulley. drive belt; refer to www.Toro.com for servicing information or take the machine to an Authorized Service Dealer. 6. The auger/impeller drive belt is worn 6. - Page 19 Problem Possible Cause Corrective Action The LED indicator light on the battery 1. There is an error in the communication 1. Remove the battery pack from the charger is blinking red. between the battery pack and the battery charger, unplug the battery charger.
- Page 20 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.