hit counter script
DeWalt DCS355D2-GB Original Instructions Manual
  1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Power Tool
  5. DCS355D2-GB
  6. Original instructions manual
DeWalt DCS355D2-GB Original Instructions Manual

DeWalt DCS355D2-GB Original Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
DCS355

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DCS355D2-GB

Summary of Contents for DeWalt DCS355D2-GB

  • Page 1 DCS355...
  • Page 2 Dansk (oversat fra original brugsvejledning) Deutsch (übersetzt von den originalanweisungen) English (original instructions) Español (traducido de las instrucciones originales) Français (traduction de la notice d’instructions originale) Italiano (tradotto dalle istruzioni originali) Nederlands (vertaald vanuit de originele instructies) Norsk (oversatt fra de originale instruksjonene) Português (traduzido das instruções originais) Suomi (käännetty alkuperäisestä...
  • Page 3 Figure 1 Figure 2...
  • Page 4 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7...
  • Page 5 Figure 8 Figure 9 Figure 10 Figure 11 Figure 12 Figure 13 Figure 14...
  • Page 6 Figure 15 Figure 16 Figure 17 Figure 18 Figure 19...

  • Page 7: Technical Data

    ENGLISH CORDLESS OSCILLATING MULTI-TOOL DCS355 The vibration emission level given in this information Congratulations! sheet has been measured in accordance with a You have chosen a D WALT tool. Years of standardised test given in EN 60745 and may be experience, thorough product development and used to compare one tool with another.

  • Page 8: Defi Nitions: Safety Guidelines

    ENGLISH Horst Grossmann Fuses Vice President Engineering and Europe 230 V tools 10 Amperes, mains Product Development U.K. & Ireland 230 V tools 13 Amperes, in plugs WALT, Richard-Klinger-Strasse 11, D-65510, Idstein, Germany Defi nitions: Safety Guidelines 03.07.2013 The definitions below describe the level of severity for each signal word.
  • Page 9 ENGLISH When operating a power tool outdoors, Do not use the power tool if the switch use an extension cord suitable for outdoor does not turn it on and off. Any power use. Use of a cord suitable for outdoor use tool that cannot be controlled with the switch is dangerous and must be repaired.

  • Page 10: Residual Risks

    ENGLISH 6) SERVICE Residual Risks Have your power tool serviced by a In spite of the application of the relevant safety qualified repair person using only identical regulations and the implementation of safety replacement parts. This will ensure that the devices, certain residual risks cannot be avoided.
  • Page 11 ENGLISH • Do not disassemble the charger; take it to CAUTION: Children should be an authorised service centre when service or supervised to ensure that they do not repair is required. Incorrect reassembly may play with the appliance. result in a risk of electric shock, electrocution or NOTICE: Under certain conditions, with fire.

  • Page 12: Charging Process

    ENGLISH READ ALL INSTRUCTIONS Charging Process • Do not charge or use the battery pack Refer to the table below for the state of charge of in explosive atmospheres, such as in the the battery pack. presence of flammable liquids, gases or State of charge dust.

  • Page 13: Storage Recommendations

    ENGLISH • If battery contents come into contact with Problem pack or charger. the skin, immediately wash the area with mild soap and water. If the battery liquid gets into the eye, rinse water over the open eye for Problem powerline. 15 minutes or until irritation ceases.

  • Page 14: Electrical Safety

    ENGLISH 25 Assorted sandpaper pieces** Electrical Safety 1 9.5 mm x 43 mm Wood detail blade** The electric motor has been designed for one 1 3 mm Carbide grout removal blade** voltage only. Always check that the battery pack (100 mm half moon) voltage corresponds to the voltage on the rating plate.
  • Page 15 ENGLISH WARNING: Use only D WALT battery and is flush with the shaft. Ensure the accessory packs and chargers. is oriented as shown in figure 4. 4. Release the accessory clamp lever. Inserting and Removing the NOTE: Some accessories, such as scrapers and Battery Pack from the Tool (fi...
  • Page 16 ENGLISH 1. Attach the cut guide block (f) by inserting 2. Insert screw (o) and washer (u) into the dust the accessory tabs (m) on the guide into the extraction adaptor (q) and tighten with the accessory side mount slots (e) on the main supplied hex key (p).

  • Page 17: Helpful Hints

    ENGLISH Proper hand position requires the tool to be held as MAINTENANCE shown in figure 14. Your D WALT power tool has been designed to operate over a long period of time with a minimum Using the Dust Extraction Adaptor of maintenance.

  • Page 18: Optional Accessories

    ENGLISH Optional Accessories Local regulations may provide for separate collection of electrical products from the household, at WARNING: Since accessories, other municipal waste sites or by the retailer when you than those offered by D WALT, have purchase a new product. not been tested with this product, use WALT provides a facility for the collection and of such accessories with this tool could...
  • Page 19 ENGLISH GUARANTEE WALT is confident of the quality of its products and offers an outstanding guarantee for professional users of the product. This guarantee statement is in addition to and in no way prejudices your contractual rights as a professional user or your statutory rights as a private non-professional user.

  • Page 20: Troubleshooting

    ENGLISH TROUBLESHOOTING PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION Unit will not Battery not Install battery in tool handle and ensure it is seated correctly. start. installed correctly. Battery is not Place battery on charger and install a fully charged battery pack in charged.

This manual is also suitable for:

Dcs355

Table of Contents