No. 0243 32LD8D20E 32LD8D20EA 32LD8D20U 32LD8D20UA SERVICE MANUAL 32LD8D20UC MANUEL D'ENTRETIEN 37LD8D20E WARTUNGSHANDBUCH 37LD8D20U 37LD8D20UA CAUTION: 37LD8D20UC Before servicing this chassis, it is important that the service technician read the “Safety Precautions” and “Product Safety Notices” in this service manual.
1. INTRODUCTION 17MB22 Main Board consists of Micronas concept , VCTP as controller. This IC is capable of handling Audio processing, video processing, motion adaptive up conversion(MAU), Scaling-Display processing and FPD control (DPS), unified memory for audio video and Text, 3D comb filter, PC connectivity, OSD and text processing. TV supports PAL, SECAM, NTSC colour standards and multiple transmission standards as B/ G, D/K, I/I’...
3. AUDIO AMPLIFIER STAGE WITH MP7722 3.1 General Description The MP7722 is a stereo 20W Class D Audio amplifier, intended for use as low frequency power amplifier in a wide range of applications in radio and TV sets. It uses a minimum number of external components to complete a stereo Class D audio amplifier.
3.3 Applications Surround Sound DVD Systems Televisions Flat Panel Monitors Multimedia Computers Home Stereo Systems 3.4 Absolute Ratings 3.5 Pinning 4. POWER STAGE The DC voltages required at various parts of the chassis and inverters are provided by a main power supply unit and power interface board. The main power supply unit is designed for 24V and 12V DC supply.
5. MICROCONTROLLER (VCTP) 5.1 General Features The VCT 6wxyP is dedicated to high-quality FPD and double-scan TV sets. The VCT 6wxyP family is based on functional blocks contained and approved in existing products like VCT 49xxI, VSP 94x5B, and DPS 94xxA. Each member of the family contains the entire audio, video, up-conversion processing for 4:3 and 16:9 50/ 60 Hz progressive or 100/120 Hz interlaced stereo TV sets and the control/data...
Page 6
non-linear colorspace enhancement (NCE) with 32 programmable slopes and sections per RGB component (blue stretch, static black stretch, gamma correction). Dynamic contrast enhancement (DCE) (histogram based black stretch with peak black and activity detection and contrast adaption) Luma sharpness enhancement (LSE) Colour transient improvement (CTI) Selective colour enhancement (SCE) for skin tone correction, blue and green stretch...
Page 7
The TVT provides an integrated general-purpose, fully 8051-compatible microcontroller with television-specific hardware features. The microcontroller has been enhanced to provide powerful features such as memory banking, data pointer, additional interrupts, shared memory access etc. The TVT has an internal XRAM of 32 KB and a BOOT ROM of 4 KB. For operation the code is fetched from a 16bit FLASH, which can be addressed up to 1 MByte.
Page 8
4-level, 24-input interrupt controller Patch module for 16 ROM locations Two 16-bit reloadable timers Capture compare timer for infrared decoding Watchdog timer Uart Real time clock PWM units (2 channels 14-bit, 6 channels 8-bit) 8-bit ADC (4 channels) I2C bus master/slave interface Up to 32 programmable I/O ports 5.5 OSD and Teletext Features The on-chip display unit for displaying Level 1.5 Teletext data can also be used for...
6. DRX 3961A 6.1 General Desription The DSP-based Analog TV IF Demodulator DRX 396xA performs the entire multistandard Quasi Split Sound (QSS) TV IF processing, AGC, video demodulation, and generation of the sound IF (SIF), requiring only one SAW filter. The IC is designed for applications in TV sets, VCRs, PC cards, and TV tuners.
Programmable IF frequency (38.9 MHz, 45.75 MHz, 32.9 MHz, 58.75 MHz, 36.125 MHz etc.) Digital IF processing for the following standards: B/G, D/K, I, L/L’, and M/N Standard specific digital post filtering Standard specific digital video/audio splitting Standard specific digital picture carrier recovery: -Alignment-free -Quartz-stable and accurate -Stable frequency lock at 100% modulation and overmodulation up to...
RANDOM and SEQUENTIAL READ Modes Self-Timed Programming Cycle Automatic Address Incrementing Enhanced ESD/Latch-Up Protection More than 1 Million Erase/Write Cycles More than 40-Year Data Retention 7.3 Absolute Maximum Ratings 7.4 Pinning 8. CLASS AB STEREO HEADPHONE DRIVER TDA1308 8.1. General Description The TDA1308 is an integrated class AB stereo headphone driver contained in an SO8 or a DIP8 plastic package.
High slew rate Low distortion Large output voltage swing. Power supply maximum 60 mW to 32 (THD<0.1%) 5V single supply SNR 110 dB Power supply ripple rejection Typically 3 mA supply current at no load 8.3. Pinning 9. SAW FILTER X6966M 9.1 Features: - IF filter for digital cable TV - Plastic package SIP5K...
10. IC DESCRIPTIONS AND INTERNAL BLOCK DIAGRAM LM1117 LM1086 MP1593 FDC642P SIL9011 24LC02 μPA672T M74HC4052 Max809 24LC21 10.1. LM1117 10.1.1. General Description The LM1117 is a series of low dropout voltage regulators with a dropout of 1.2V at 800mA of load current. It has the same pin-out as National Semiconductor’s industry standard LM317.
Page 23
10.1.4. Absolute Maximum Ratings 10.1.5. Pinning 10.2. LM1086 10.2.1. General Description The LM1086 is a low dropout three terminal regulator with 1.5A output current capability. The output voltage is adjustable with the use of a resistor divider. Dropout is guaranteed at a maximum of 500 mV at maximum output current.
Page 24
High Efficiency "Green" Computer Systems SMPS Post-Regulator Power PC Supplies Powering VGA & Sound Card 10.2.4. Absolute Maximum Ratings 10.2.5. Pinning 10.3. MP1593 10.3.1. General Description The MP1593 is a step-down regulator with an internal Power MOSFET. It achieves 3A continuous output current over a wide input supply range with excellent load and line regulation.
Page 25
10.3.2. Features 3A Output Current Programmable Soft-Start 100m Internal Power MOSFET Switch Stable with Low ESR Output Ceramic Capacitors Up to 95% Efficiency 20μA Shutdown Mode Fixed 385KHz Frequency Thermal Shutdown Cycle-by-Cycle Over Current Protection Wide 4.75 to 28V Operating Input Range Output Adjustable from 1.22V Under Voltage Lockout Available in 8-Pin SOIC Package...
Page 26
10.3.5. Electrical Characteristics 10.3.6. Pinning Pin1:BS High-Side Gate Drive Boost Input. BS supplies the drive for the high-side N-Channel MOSFET switch. Connect a 10nF or greater capacitor from SW to BS to power the high side switch. Pin2:IN Power Input. IN supplies the power to the IC, as well as the step-down converter switches.
Page 27
Soft-Start Control Input. SS controls the soft-start period. Connect a capacitor from SS to GND to set the soft-start period. A 0.1μF capacitor sets the soft-start period to 10ms. To disable the soft-start feature, leave SS unconnected. 10.4. FDC642P 10.4.1. General Description This p-channel 2.5V specified MOSFET is produced using Fairchild’s advanced PowerTrench process that has been especially tailored to minimize on state resistance and yet maintain low gate charge for superior switching performance.
Page 28
10.5. SIL9011 The Sil 9011 is a third generation HDMI receiver compatible with the HDMI 1.1 specification. Backwards compatibility with DVI 1.0 allows HDMI systems to connect to existing DVI 1.0 hosts over a single cable. The Sil 9011 is capable of receiving and outputting 2 to 8 channels of digital audio of up to 192kHz.
Page 29
Organized as 1 block of 256 bytes (1 x 256 x 8) 2-wire serial interface bus, I C™ compatible Schmitt Trigger inputs for noise suppression Output slope control to eliminate ground bounce 100 kHz (24AA02) and 400 kHz (24LC02B) compatibility Self-timed write cycle (including auto-erase) Page write buffer for up to 8 bytes 2ms typical write cycle time for page write...
Page 30
10.7.2. Features Two MOS FET circuits in package the same size as SC-70 Automatic mounting supported 10.7.3 Absolute Maximum Ratings 10.7.4 Pinning 10.8. M74HC4052 10.8.1. General Description The M74HC4052 is a dual four-channel analog MULTIPLEXER/DEMULTIPLEXER fabricated with silicon gate C2MOS technology and it is pin to pin compatible with the equivalent metal gate CMOS4000B series.
Page 31
70W TYP. (VCC - VEE = 4.5V) 50W TYP. (VCC - VEE = 9V) WIDE ANALOG INPUT VOLTAGE RANGE: ±6V FAST SWITCHING: tpd = 15ns (TYP.) at TA = 25 °C LOW CROSSTALK BETWEEN SWITCHES HIGH ON/OFF OUTPUT VOLTAGE RATIO WIDE OPERATING SUPPLY VOLTAGE RANGE (VCC - VEE) = 2V TO 12V LOW SINE WAVE DISTORTION: 0.02% at VCC - VEE = 9V HIGH NOISE IMMUNITY: VNIH = VNIL = 28 % VCC (MIN.)
Page 32
10.9. Max809 10.9.1. General Description The MAX809 and MAX810 are cost effective system supervisor circuits designed to monitor VCC in digital systems and provide a reset signal to the host processor when necessary. No external components are required. The reset output is driven active within 10 _sec of VCC falling through the reset voltage threshold.
Page 34
10.10. 24LC21 10.10.1. General Description The 24LC21 is a 1K bit electrically erasable programmable memory (EEPROM), organized by 8 bits.This device can operate in two modes: Transmit Only mode and I2C bidirectional mode. When powered, the device is in Transmit Only mode with EEPROM data clocked out from the rising edge of the signal applied on VCLK.
10.10.4 Pinning 11.SERVICE MENU SETTINGS In order to reach service menu, First Press “MENU” Then press the remote control code, which is “4725” 11.1. Video Setup Picture Mute <..> If “Yes” selected, “Picture mute” feature is active. Blue Screen <..> If “Yes”...
Page 36
SRS WOW Virtual Dolby Surround <..> If “Yes” selected, Virtual Dolby Surround feature is seen in “Sound” menu with selected Virtual Dolby Text. Virtual Dolby Text The selected item is seen as Virtual Dolby Srround Text. Virtual Dolby 3D Panorama AVL <..>...
Page 37
Select Languages <..> “Yes” selected languages are seen as option under the “Language” item in “Feature” menu Language Set 1 o German <..> o French <..> o Spanish <..> o Italian <..> o Danish <..> o Finnish <..> o Swedish <..> Language Set 2 o Greek <..>...
Page 38
11.5. Service Scan/Tuning Setup Search for L/L’ <..> Pref. Search Standard <...> BG, DK, I L/L’ Station Ident <..> ATS Delay Time (ms) <..> Value between 20 to 250 Color Killer Threshold <..> Value between 0 to +255 Tuner Options <..> Control Byte <..>...
Page 39
x Colour Temp <..> Cool Normal Warm x Contrast <..> Value between 0 to +63 x Brightness <..> Value between 0 to +63 x Sharpness <..> Value between 0 to +15 x Colour <..> Value between 0 to +63 x Backlight <..> Value between 0 to +255 x R <..>...
Page 40
NO DEFECT APPEARANCE DEFECT IDENTIFICATION AND SOLUTIONS When the TV is operated for the first time, IC403 E2Epron is plugged empty, after the programming process of the first values has finished, TV will switch on by itself. STANDBY LED lights but the TV switches on Are there 3.3V on IC001's bottomright pin? If no, 3.3V are not drawing in, there can be an error in PW board;...
Page 48
13.5.1 IDTV Module Block Diagram ANALOG AV CON POWER IF INPUT BUCK SAW Filter VIDEO AUDIO 3.3V 1.8V 1.5V LIN.REGULATOR S/PDIF EMMA2LL COFDM DEMOD 16 MB CPU + MPEG DECODER DDRAM VCXO 2 MB PROGRAM FLASH (UART) JTAG DIGITAL AV CON BUFFERS &...
Page 50
14.4. IF Connector Description IF + IF - 14.5. PROGRAMMING Connector Description 14.6. S/PDIF Connector Description S/PDIF 14.7. DIGITAL AV Connector Description Description 1 I2S Word Select 11 GND 2 I2S Serial Clock 12 Digital Video Pixel Clock 3 I2S Serial Data 13 Digital Video Y/Cb/Cr DATA7 4 GND 14 Digital Video Y/Cb/Cr DATA6...
Page 51
14.8. PCMCIA Connector Signal Description Signal Description 35 GND Ground Ground 36 CD1# Data bit 3 Card Detect 37 MDO3 Data bit 4 MPEG Data Out 3 38 MDO4 Data bit 5 MPEG Data Out 4 39 MDO5 Data bit 6 MPEG Data Out 5 40 MDO6 Data bit 7...
15. CONCEPT ICs 15.1. μPD61115 15.1.1 Description The μPD61115 device is a member of the second generation of multimedia processors based on NEC’s Enhanced MultiMedia Architecture (EMMArchitecture). These devices provide nearly all the functionality required to realise a high performance and cost-effective digital set-top box or integrated digital TV. 15.1.2 Features MPEG1 and MPEG2-TS/PS compliant High performance MIPS32™...
Page 53
15.2.2 Features Highest level of front-end integration and flexibility: Integrated PGA (programmable gain amplifier) 30 dB Single 8 MHz SAW filter operation 2 AGC control signals available for RF and IF amplifier control Flexible clock reference options Re-use of 4 MHz tuner clock reference Pre-SAW sense input for optimal RF AGC setting and RF-level measurement Excellent digital reception performance: Superior digital and analog adjacent channel performance (>...
Page 54
15.3.2 Description The PI6CX100-27 is a low-cost, high-performance 3.3V VCXO, designed to replace expensive VCXO modules. The on-chip Voltage Controlled Crystal Oscillator accepts a 0 to 3.3V input voltage to cause clocks to vary by ±120ppm. This device uses an inexpensive external pullable crystal at 27 MHz to produce the same output frequency.The PI6CX100-27 is designed for Set-Top Box applications.
Page 55
15.5.2 Applications Cable set top boxes Satellite set top boxes DVD players HDTV Personal video recorders (PVR) Video on demand (VOD) 15.5.3 Description The FMS6145 Low Cost Video Filter (LCVF) is intended to replace passive LC filters and drivers with a low-cost integrated device.
Page 56
Thermal Shutdown Cycle-by-Cycle Over Current Protection Wide 4.75 to 28V Operating Input Range Output Adjustable from 1.22Vs Under Voltage Lockout Available in 8-Pin SOIC Package 15.6.3 Applications Distributed Power Systems Battery Chargers Pre-Regulator for Linear Regulators Flat Panel TVs Set-Top Boxes Cigarette Lighter Powered Devices DVD/PVR Devices...
Page 63
SHEET2 S612 OPTIONAL L603 HP_OUT_L VIN_24V AMP_24V BC558B Q603 VCC_5V D611 L604 1N4148 22uH_3.9A_SMD IC600 D610 C614 C3V6 C636 1000UF 30000361 USED 8 VDD OUTA HP_OUT_R 100u SHEET3 TO REDUCE POWER C623 R613 ON HP POPPING IF AMP_MUTE HIGH ENOUGH TO ENABLE AMPLIFIER OPTIONAL RESISTOR WILL BE USED 7 OUTB INA- HEADPHONE_R...
19. PCB Layout Diagrams [17PW15-9 POWER BOARD used in 32LD8D20E, 32LD8D20U, 37LD8D20U and 37LD8D20UA models ONLY] S914 C495 R420 R487 PL210 LIVE L904 S911 R403 PL200 C873 R543 S462 C873 R1010 R224 C918 C810 L815 R1008 R1004 R981 R912 S908...
Page 76
[17PW15-9 POWER BOARD used in 32LD8D20E, 32LD8D20U, 37LD8D20U and 37LD8D20UA models ONLY] POWER BOARD (17PW15-9) MAIN BOARD (17MB22-2) TDM1300 IDTV MODULE FAV BOARD (17FAV15) BOARD (16MB1300-E1) No. 0243 PHOTOGRAPHS OF CHASSIS AND BOARDS...
Page 77
Fax: +46 (0) 8 562 711 13 Tel: +39 02 38073415 Servizio Clienti Email: csgswe@hitachi-eu.com Fax: +39 02 48786381/2 Email: customerservice.italy@hitachi-eu.com HITACHI EUROPE S.A.S HITACHI EUROPE LTD (Norway) AB Lyon Office STRANDVEIEN 18 B.P. 45, 69671 BRON CEDEX 1366 Lysaker FRANCE...