hit counter script
Download
Share
Print this page
Hitachi CP-WX1100 Technical Manual
  1. Manuals
  2. Brands
  3. Hitachi Manuals
  4. Projector
  5. CP-WX1100
  6. Technical manual
Hitachi CP-WX1100 Technical Manual

Hitachi CP-WX1100 Technical Manual

Technical manual
Hide thumbs Also See for CP-WX1100:

Advertisement

Quick Links

Download this manual See also: User Manual, Network Manual
Projector
CP-X10000/CP-WX11000/CP-SX12000
User's Manual – Operating Guide
Technical

Example of computer signal

Example of computer signal
Resolution (H x V) H. frequency (kHz) V. frequency (Hz)
720 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1280 x 960
1280 x 1024
1280 x 1024
*1280 x 1024
*1600 x 1200
1280 x 768
1400 x 1050
1280 x800
NOTE
• Be sure to check jack type, signal level, timing and resolution
before connecting this projector to a computer.
• Some computers may have multiple display screen modes. Use of some of
these modes will not be possible with this projector.
• Depending on the input signal, full-size display may not be possible in some
cases. Refer to the number of display pixels above.
• Although the projector can display signals with resolution up to UXGA
(1600x1200), the signal will be converted to the projector's panel resolution
before being displayed. The best display performance will be achieved if the
resolutions of the input signal and projector panel are identical.
• Automatic adjustment may not function correctly with some input signals.
• The image may not be displayed correctly when the input sync signal is a
composite sync or a sync on G.
• The HDMI input does not support the signals marked with *.
37.9
31.5
37.9
37.5
43.3
35.2
37.9
48.1
46.9
53.7
49.7
48.4
56.5
60.0
68.7
67.5
60.0
64.0
80.0
91.2
75.0
47.7
65.3
49.7
Rating
85.0
VESA
59.9
VESA
72.8
VESA
75.0
VESA
85.0
VESA
56.3
VESA
60.3
VESA
72.2
VESA
75.0
VESA
85.1
VESA
74.5
60.0
VESA
70.1
VESA
75.0
VESA
85.0
VESA
75.0
VESA
60.0
VESA
60.0
VESA
75.0
VESA
85.0
VESA
60.0
VESA
60.0
VESA
60.0
VESA
60.0
VESA
Signal mode
TEXT
VGA (60Hz)
VGA (72Hz)
VGA (75Hz)
VGA (85Hz)
SVGA (56Hz)
SVGA (60Hz)
SVGA (72Hz)
SVGA (75Hz)
SVGA (85Hz)
Mac 16" mode
XGA (60Hz)
XGA (70Hz)
XGA (75Hz)
XGA (85Hz)
1152 x 864 (75Hz)
1280 x 960 (60Hz)
SXGA (60Hz)
SXGA (75Hz)
SXGA (85Hz)
UXGA (60Hz)
W-XGA (60Hz)
SXGA+ (60Hz)
1280 x 800 (60Hz)
1

Advertisement

loading

Related Manuals for Hitachi CP-WX1100

Summary of Contents for Hitachi CP-WX1100

  • Page 1: Example Of Computer Signal

    Projector CP-X10000/CP-WX11000/CP-SX12000 User's Manual – Operating Guide Technical Example of computer signal Example of computer signal Resolution (H x V) H. frequency (kHz) V. frequency (Hz) Rating Signal mode 720 x 400 37.9 85.0 VESA TEXT 640 x 480 31.5 59.9 VESA VGA (60Hz)
  • Page 2 Initial set signals Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu. Back porch (B) Front porch (D) Back porch (b)
  • Page 3 Connection to the ports Connection to the ports Connection to the ports MONITOR HDMI DVI-D CONTROL IN CONTROL OUT REMOTE S-VIDEO CONTROL COMPUTER IN1 COMPUTER IN2 VIDEO 1 R/Cr/Pr G/Y B/Cb/Pb H V VIDEO 2 Cb/Pb Cr/Pr AC IN COMPUTER IN1, COMPUTER IN2, MONITOR OUT D-sub 15pin mini shrink jack...
  • Page 4 Connection to the ports (continued) MONITOR HDMI DVI-D CONTROL IN CONTROL OUT REMOTE S-VIDEO CONTROL COMPUTER IN1 COMPUTER IN2 VIDEO 1 R/Cr/Pr G/Y B/Cb/Pb H V VIDEO 2 Cb/Pb Cr/Pr AC IN S-VIDEO Mini DIN 4pin jack Signal Color signal 0.286Vp-p (NTSC, burst), 75Ω terminator Color signal 0.300Vp-p (PAL/SECAM, burst) 75Ω...
  • Page 5 Connection to the ports (continued) MONITOR HDMI DVI-D CONTROL IN CONTROL OUT REMOTE S-VIDEO CONTROL COMPUTER IN1 COMPUTER IN2 VIDEO 1 R/Cr/Pr G/Y B/Cb/Pb H V VIDEO 2 Cb/Pb Cr/Pr AC IN HDMI 18 16 14 12 10 • Type :Digital video connector 19 17 15 13 11 Signal Signal...

  • Page 6: Pjlink Command

    PJLink command PJLink command PJLink command This projector is equipped with the PJLink Class 1. See the following table for the commands for controlling the projector using the PJLink protocol are as given in the table below. Commands Control Description Parameter or Response 0 = Standby POWR...
  • Page 7 11 12 13 21 22 23 24 31 32 Responds with the name set in "PROJECTOR NAME" NAME ? Projector Name inquiry of "NETWORK" INF1 ? Manufucturer's Name inquiry HITACHI CP-X10000 (XGA model) INF2 ? Model Name inquiry CP-WX11000 (WXGA model) CP-SX12000 (SXGA+ model)

  • Page 8: Connecting The Cable

    RS-232C Communication RS-232C Communication RS-232C Communication CONTROL port RS-232C cable (Cross) RS-232C port of the projector of the computer - (1) (1) CD RD (2) (2) RD TD (3) (3) TD - (4) (4) DTR GND (5) (5) GND - (6) (6) DSR RTS (7) (7) RTS...
  • Page 9 RS-232C Communication (continued) Requesting projector status (Get command) (1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes)+‘00H’ +‘00H’) from the computer to the projector. (2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer. Changing the projector settings (Set command) (1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) + setting code (2 bytes)) from the computer to the projector.

  • Page 10: Command Control Via The Network

    Command Control via the Network Command Control via the Network Command Control via the Network Communication Port The following two ports are assigned for the command control. TCP #23 TCP #9715 Command Control Settings Confi gure the following items form a web browser when command control is used. Port Settings Click the [Enable] check box to open [Network Port open...

  • Page 11: Command Format

    Command Control via the Network (continued) Command Format [TCP #23] 1. Protocol Consist of header (7 bytes) + command data (6 bytes) 2. Header BE + EF + 03 + 06 + 00 + CRC_low + CRC_high CRC_low: Lower byte of CRC fl ag for command data CRC_high: Upper byte of CRC fl...
  • Page 12 Command Control via the Network (continued) Decreasing the projector setting value (Decrement command) (1) The PC sends the following decrement code to the projector. Header + Command data (‘05H’ + ‘00H’ + type (2 bytes) + ‘00H’ + ‘00H’) (2) The projector decreases the setting value on the above setting code. (3) The projector returns the response code ‘06H’...
  • Page 13 Command Control via the Network (continued) 7. Reply Data The connection ID (the data is same as the connection ID data on the sending data format) is attached to the Network control commands reply data. ACK reply: ‘06H’ + ‘xxH’ NAK reply: ‘15H’...
  • Page 14 Daisy Chain Communication Daisy Chain Communication Daisy Chain Communication Recieving side Transmitting side CONTROL OUT port RS-232C cable (Cross) CONTROL IN in Projector port in Projector - (1) (1) CD RD (2) (2) RD TD (3) (3) TD - (4) (4) DTR GND (5) (5) GND...
  • Page 15 Daisy Chain Communication Calculation of Checksum Sum up all of 12 bytes except the Checksum, then make the bit inversion of the lowest byte of the total, and add 1 to the inverted byte. The calculated result is the Checksum data. Exp.
  • Page 16 Daisy Chain Communication Command data ① Control the projector byte_0 byte_1 byte_2 byte_3 byte_4 byte_5 Action Type Setting Code high high high Action (byte_0-1) Action Content Classification Change setting to desired value. Increment Increment setup value by 1. Decrement Decrement setup value by 1. Execute Run a command.
  • Page 17 Daisy Chain Communication Command data Requesting projector status (Get command) (1) Send the following request code from the PC to the projector. Header + Command data (‘02H’ + ‘00H’ + type (2 bytes) + connection ID (2 bytes)) (2) The projector returns the response code to the PC. ‘9DH’...
  • Page 18 Daisy Chain Communication Get the number of connected projectors (1) Send the following request code from the PC to the projector. Header + Command data (‘02H’ + ‘00H’ + ‘00H’ + ‘00H’ + connection ID (2 bytes)) (2) The projector returns the response code to the PC. ‘9EH’...
  • Page 19 Daisy Chain Communication Get the communication Group identification and Communication ID (1) Send the following request code from the PC to the projector. Header + Command data (‘02H’ + ‘00H’ + target number (2 bytes) + connection ID (2 bytes)) (2) The projector returns the response code to the PC.
  • Page 20 RS-232C Communication / Network command table RS-232C Communication / Network command table RS-232C Communication / Network command table Command Data Names Operation Type Header Action Type Setting Code Power BE EF 06 00 2A D3 01 00 00 60 00 00 BE EF 06 00 BA D2...
  • Page 21 RS-232C Communication / Network command table Command Data Names Operation Type Header Action Type Setting Code GAMMA 5 CUSTOM BE EF 06 00 C7 FF 01 00 A1 30 14 00 6 CUSTOM BE EF 06 00 57 FE 01 00 A1 30 15 00 BE EF...
  • Page 22 RS-232C Communication / Network command table Command Data Names Operation Type Header Action Type Setting Code COLOR TEMP GAIN R BE EF 06 00 34 F4 02 00 B1 30 00 00 Increment BE EF 06 00 52 F4 04 00 B1 30 00 00 Decrement...
  • Page 23 RS-232C Communication / Network command table Command Data Names Operation Type Header Action Type Setting Code 3D-YCS BE EF 06 00 E6 70 01 00 0A 22 00 00 MOVIE BE EF 06 00 76 71 01 00 0A 22 01 00 STILL IMAGE BE EF...
  • Page 24 RS-232C Communication / Network command table Command Data Names Operation Type Header Action Type Setting Code S-VIDEO FORMAT AUTO BE EF 06 00 E6 70 01 00 12 22 0A 00 NTSC BE EF 06 00 86 74 01 00 12 22 04 00 BE EF...
  • Page 25 RS-232C Communication / Network command table Command Data Names Operation Type Header Action Type Setting Code FRAME LOCK - BE EF 06 00 3B C2 01 00 50 30 00 00 COMPUTER IN 1 BE EF 06 00 AB C3 01 00 50 30 01 00...
  • Page 26 RS-232C Communication / Network command table Command Data Names Operation Type Header Action Type Setting Code MONITOR OUT - COMPUTER IN 1 BE EF 06 00 7A F4 01 00 B3 20 00 00 HDMI COMPUTER IN 2 BE EF 06 00 BA F6 01 00...
  • Page 27 RS-232C Communication / Network command table Command Data Names Operation Type Header Action Type Setting Code LANGUAGE POLSKI BE EF 06 00 97 D7 01 00 05 30 0E 00 TÜRKÇE BE EF 06 00 07 D6 01 00 05 30 0F 00 DANSK BE EF...
  • Page 28 RS-232C Communication / Network command table Command Data Names Operation Type Header Action Type Setting Code CLOSED CAPTION BE EF 06 00 D2 62 01 00 02 37 01 00 CHANNEL BE EF 06 00 22 62 01 00 02 37 02 00 BE EF 06 00...
  • Page 29 RS-232C Communication / Network command table Command Data Names Operation Type Header Action Type Setting Code MY BUTTON-1 COMPUTER IN 1 BE EF 06 00 3A 33 01 00 00 36 00 00 COMPUTER IN 2 BE EF 06 00 FA 31 01 00 00 36...
  • Page 30 RS-232C Communication / Network command table Command Data Names Operation Type Header Action Type Setting Code MY BUTTON-3 DVI-D BE EF 06 00 D2 34 01 00 02 36 09 00 COMPONENT BE EF 06 00 D2 31 01 00 02 36 05 00 S-VIDEO...
  • Page 31 RS-232C Communication / Network command table Command Data Names Operation Type Header Action Type Setting Code MY SOURCE BE EF 06 00 C9 38 02 00 20 36 00 00 MY IMAGE BE EF 06 00 3A C3 01 00 00 35 00 00 IMAGE-1...
  • Page 32 RS-232C Communication / Network command table Command Data Names Operation Type Header Action Type Setting Code LENS MEMORY INDEX Set BE EF 06 00 4B 92 01 00 07 24 00 00 BE EF 06 00 DB 93 01 00 07 24 01 00 BE EF...

This manual is also suitable for:

Cp-wx11000Cp-sx12000Cp-x10000