Table of Contents
Related Manuals for Miele DA 3060
Summary of Contents for Miele DA 3060
- Page 1 Operating and installation instructions Cooker hood DA 3060 en - GB To avoid the risk of accidents or damage to this appliance, it is essential to read these instructions before it is installed and used for the first time. M.-Nr. 07 773 930...
-
Page 2: Table Of Contents
Contents Caring for the environment ......... . 3 Warning and Safety instructions . -
Page 3: Caring For The Environment
Caring for the environment Disposal of the packing material Disposal of your old appliance The transport and protective packing Electrical and electronic appliances has been selected from materials which often contain materials which, if are environmentally friendly for handled or disposed of incorrectly, disposal, and should be recycled. -
Page 4: Warning And Safety Instructions
Any other usage is not supported by This appliance complies with all the manufacturer and could be relevant local and national safety dangerous. Miele cannot be held liable requirements. Inappropriate use for damage resulting from incorrect or can, however, lead to personal injury improper use or operation of the and damage to property. -
Page 5: Technical Safety
Technical safety Installation, maintenance and repairs may only be carried out by a Before installation, check the cooker Miele authorised person in accordance hood for visible signs of damage. with current national and local safety Under no circumstances should you regulations. - Page 6 Warning and Safety instructions Do not connect the appliance to the Using at the same time as other mains electricity supply by a heating appliances that depend on multi-socket unit or an extension lead. the air from the room These do not guarantee the required safety of the appliance (e.g.
-
Page 7: Correct Use
Warning and Safety instructions Correct use In order to ensure safe operation, and to prevent gases given off by the Never use an open flame beneath heating appliances from being drawn the cooker hood. To avoid the danger back into the room when the cooker of fire, do not flambé... -
Page 8: Correct Installation
All ducting, pipework and fittings "Cleaning and care". must be of non-flammable material. The cooker hood can get very hot These can be obtained from the Miele during cooking due to heat rising from Spare Parts department or from the hob. -
Page 9: Description Of The Functions
Charcoal filters are available to order socket in the motor unit. through your Dealer / Chartered Agent or the Miele Spare Parts Department or Having a non-return flap fitted in the via the internet at www.miele-shop.com. ducting ensures that air, once ducted... -
Page 10: Guide To The Appliance
Guide to the appliance... -
Page 11: Guide To The Appliance
Guide to the appliance Exhaust socket ø 150 mm Sliding switch for the fan ^ Pull out the deflector plate. Control panel ^ To switch on, slide the switch to the Grease filter required setting. Pull-out deflector plate Depending on the intensity of the Hob lighting cooking vapours, levels "1"... -
Page 12: Cleaning And Care
Cleaning and care A range of Miele branded cleaning and Do not use too much water when conditioning agents are available to cleaning the controls. Water could order through your Miele Dealer / Chartered Agent, the Miele Spare Parts penetrate into the electronics and cause damage. -
Page 13: Grease Filter
Cleaning and care Grease filter Controls The re-usable metal grease filter in the The controls may suffer appliance removes solid particles from discolouration or damage if soiling is the kitchen vapours (grease, dust, etc) left on them for too long. Remove preventing soiling of the cooker hood. - Page 14 ^ Do not wash at more than 65° C. If a the deflector plate. It will slide onto the fixing pins at the back. Finally, Miele dishwasher is being used, push the grease filter back a little select the Sensor wash programme.
-
Page 15: Fitting And Replacing The Charcoal Filter
It is fitted in the canopy above the grease filter. Replacement charcoal filters can be obtained from your Dealer / Chartered Agent or the Miele Spare Parts department or via the internet at www.miele-shop.com. See back cover for contact details, and "Technical data"... -
Page 16: Changing A Halogen Lamp
Cleaning and care Changing a halogen lamp ^ Pull out the deflector plate, and remove the grease filter as described earlier. ^ Switch off the fan and the lighting. Exercise caution when changing halogen lamps. They get very hot during use, and remain hot for some time after being switched off. -
Page 17: Appliance Dimensions
– 650 mm above gas hobs and cookers. If this cooker hood is installed above a Miele Wok CS 1028 CombiSet appliance, a minimum safety distance of 760 mm must be maintained between the burner and 1) The front section of the wall housing the lower edge of the cooker hood. -
Page 18: Installation
Installation Installation accessories... - Page 19 Installation 1 exhaust connection for exhaust ducting C 150 mm. 1 reducing collar 12 screws 3.5 x 16 mm for exhaust ducting C125 mm. for securing the cooker hood into the wall unit. 1 non-return flap for fitting into the exhaust socket on the motor unit (only for air extraction mode).
- Page 20 Installation...
-
Page 21: Positioning The Appliance In The Wall Housing Unit
Installation Positioning the appliance in the wall housing unit To position the appliance correctly, cut the spacer strip to required depth T, and then attach it to the back of the appliance. T= Depth of carcase K minus depth of ^ Screw the spacer strip to the bottom appliance G of the sides of the housing, flush with... - Page 22 Installation ^ Place the appliance on its back. Do not remove the protective film between the deflector plate and the casing until the hood has been placed in the housing unit. ^ Screw the brackets onto the right and left inside walls of the housing unit as shown.
- Page 23 Installation Note for dismantling the cooker hood: Undoing the screws on the left and right inside the housing releases the brackets, allowing the appliance to be removed from the unit. ^ Push the cooker hood back against the spacer strip. ^ Pull out the deflector plate.
- Page 24 Installation ^ Secure the front of the appliance to the floor of the housing unit from below using 4 screws. ^ Drill respective holes and screw the fixing brackets to the wall or the To avoid damaging the deflector plate cabinet rear wall.
-
Page 25: Attaching The Lightshield
Installation Attaching the lightshield Aligning the deflector plate ^ Attach the lightshield (if using). A DML 300 installation kit, available as an optional accessory, is required for this. This installation kit is supplied with the DFB lightshield. Follow the ^ The position of the deflector plate installation instructions supplied. -
Page 26: Fitting The Grease Filter
Installation Fitting the grease filter ^ Remove the protective strip around the edge of the grease filter. Fit the grease filter. ^ To do this, pull the deflector plate out. ^ Turn the grease filter so that the red plastic guides are at the front and facing upwards. -
Page 27: Set Up For Extraction Mode
Installation Set up for extraction mode ^ If the on-site ventilation system does not have a non-return flap, then the non-return flap supplied with the appliance must be fitted in the ^ When using C 150 mm ducting, exhaust socket in the motor unit. secure the exhaust connection supplied to exhaust ducting with hose clips. -
Page 28: Set Up For Recirculation Mode
“Warning and Safety instructions” before connecting to the electricity supply. For this, a conversion kit DUU 151, available from your Miele dealer or the Miele Spare Parts Dept., is required. You will also need a charcoal filter (see “Technical data”). -
Page 29: Connection For Air Extraction
Connection for air extraction – Where ducting is horizontal, it must Important: To avoid the danger of be laid to slope away at at least 1 cm toxic fumes, please observe the per metre. This is to ensure that Warning and Safety instructions. condensate cannot drain back into This is especially crucial when using the cooker hood. -
Page 30: Condensate Trap
Connection for air extraction Condensate trap (optional accessory) In addition to insulating the exhaust ducting, we recommend that a suitable condensate trap is also installed to collect and evaporate any condensate which may occur. Condensate traps are available for C 125 mm or C 150 mm ducting. -
Page 31: Silencer
Connection for air extraction Silencer (optional accessory) ...with air extraction: The silencer not only reduces noise from the fan, but also sounds from outside (e.g. traffic noise). To achieve even further reductions in For this reason the silencer must be noise levels, a special silencer can be positioned as close as possible to where fitted in the ducting system. -
Page 32: Electrical Connection
Electrical connection If the switch is not accessible after All electrical work should be installation (depending on country), an undertaken by a suitably qualified additional means of disconnection must and competent person in strict be provided for all poles. accordance with current national For extra safety it is advisable to protect and local safety regulations the appliance with a suitable residual... -
Page 33: After Sales Service
In the event of a fault which you cannot correct yourself, or if the appliance is under guarantee, please contact: – Your Miele Dealer / Chartered Agent – The Miele Service Department (see back cover for address). When contacting your Dealer or Miele, please quote the model and serial number of your appliance. -
Page 34: Technical Data
Hob lighting ... . . 2 x 50 W - Conversion Kit DUU 151 - Miele charcoal filter DKF 13-1 Voltage ....230 V Frequency. - Page 36 Alteration rights reserved / 1111 M.-Nr. 07 773 930 / 02...