Table of Contents
Advertisement
Quick Links
July, 2002
These release notes provide information on the Catalyst 1900 and Catalyst 2820 series Ethernet switches
(hereafter referred to as the Catalyst 1900 switches and the Catalyst 2820 switches) using standard and
Enterprise Edition firmware version 9.00.06.
This document describes the problems that are resolved in versions 9.00.00 through 9.00.06.
Note
Contents
This document has these sections:
•
•
•
•
•
•
•
•
•
The tracking numbers for some items in this document are added for your convenience.
Corporate Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Copyright © 2002. Cisco Systems, Inc. All rights reserved.
Advertisement
Table of Contents
Related Manuals for Cisco 2820
Summary of Contents for Cisco 2820
-
Page 1: Table Of Contents
July, 2002 These release notes provide information on the Catalyst 1900 and Catalyst 2820 series Ethernet switches (hereafter referred to as the Catalyst 1900 switches and the Catalyst 2820 switches) using standard and Enterprise Edition firmware version 9.00.06. This document describes the problems that are resolved in versions 9.00.00 through 9.00.06. -
Page 2: Release Notes For The Catalyst 1900 And Catalyst 2820 Series Switches, Version 9.00.06
Catalyst 2820-A 8.01.01 or later Catalyst 2820-EN Supported Browsers To use the Catalyst 1900 or Catalyst 2820 Switch Manager, you must have one of these web browsers installed on your management station: Table 2 Browser Support for Web-Based Management Browser... -
Page 3: Features" Section
The Catalyst 1900 or Catalyst 2820 switch must be Cisco Discovery Protocol (CDP) version 2-enabled. – The Catalyst 1900 or Catalyst 2820 switch must be connected to a cluster member or to a command switch port that belongs to the management VLAN on the command switch. •... -
Page 4: Limitations" Section
Parameter value ranges are provided in the management console, the switch manager online help, and the Catalyst 1900 Series Installation and Configuration Guide and the Catalyst 2820 Series Installation and Configuration Guide. - Page 5 LED on the switch turns amber. The module continues operation, but the module image in Flash memory is corrupted. When you reset the ATM module, it will not find a valid Cisco IOS image, and the ATM module will not pass the power-on self-test (POST). To correct this problem, repeat the firmware upgrade procedure to download a new firmware image on the ATM module.
- Page 6 If you turn off the switch too soon, the changes to the switch configuration are lost the next time the system is restarted. Release Notes for the Catalyst 1900 and Catalyst 2820 Series Switches, Version 9.00.06 OL-2901-01...
-
Page 7: Caveats" Section
• When using Netscape Communicator 4.xx on PCs and Sun workstations, minimized, maximized and resized pages of the Catalyst 1900 and Catalyst 2820 Switch Manager might not refresh properly. The workaround is to click Reload to refresh the page. CSCdj95153 •... - Page 8 CSCdk69024 • If there are two or more Catalyst 1900 or Catalyst 2820 switches connected to a Catalyst 5000 switch by using Fast EtherChannel—and if there are two stations communicating through the Catalyst 5000 switch—the switches learn the addresses of both stations from the broadcast packets sent from those stations.
- Page 9 VTP pruning. CSCdp08683 • When a Catalyst 1900 or Catalyst 2820 switch is operating at the edge of a VTP domain and is subsequently configured for VTP transparent mode, trunk ports will not be in the correct pruning state.
- Page 10 CSCdx06779 • When using the Cisco Secure User Registration Tool, you can now use ports one through nine on an access-layer Catalyst 1900 or Catalyst 2820 switch. The login user is assigned to a login VLAN and to a user VLAN.
- Page 11 CSCdt65828 • The FDDI DAS module no longer incorrectly appears as an SAS module in a Catalyst 2820 switch. • CSCdr56930 The show cdp neighbor detail command now works correctly on the switch and no longer shows only the IP address of the command switch.
- Page 12 CSCds28410 • Version 9.00.04 corrected a condition on the Catalyst 1900 and 2820 switches running Enterprise Edition firmware that caused VLAN Trunk Protocol (VTP) configuration information to be lost. The VTP mode changes from transparent or server mode to client mode after VTP parameters are configured.
-
Page 13: Related Documentation" Section
The following sections explain how to obtain documentation from Cisco Systems. World Wide Web You can access the most current Cisco documentation on the World Wide Web at the following URL: http://www.cisco.com Translated documentation is available at the following URL: http://www.cisco.com/public/countries_languages.shtml... -
Page 14: Obtaining Technical Assistance" Section
America, by calling 800 553-NETS (6387). Documentation Feedback If you are reading Cisco product documentation on the World Wide Web, you can send us your comments by completing the online survey. When you display the document listing for this platform, click Give Us Your Feedback. - Page 15 • will occur if service is not restored quickly. No workaround is available. Which Cisco TAC resource you choose is based on the priority of the problem and the conditions of service contracts, when applicable. Release Notes for the Catalyst 1900 and Catalyst 2820 Series Switches, Version 9.00.06...
- Page 16 Cisco TAC Web Site. The Cisco TAC Web Site requires a Cisco.com login ID and password. If you have a valid service contract but do not have a login ID or password, go to the following URL to register: http://www.cisco.com/register/...