Table of Contents
Advertisement
Tumble Action Laundry
Center
Gas & Electric
Before
beginning
installation,
carefully
read these
instructions.
This will
simplify
the installation
and ensure
the laundry
center
is installed
correctly
and safely.
Leave
these
instructions
near
the
laundry
center
after
installation
for future
reference.
NOTE:
The electrical
service
to the laundry
center
must
conform
with
local codes and ordinances
and
the latest
edition
of the
NationalElectrical
Code, ANSI/NFPA
70, or in Canada,
the
Canadian
Electrical
Code,
CSA C22. I
NOTE:
The gas service
to the laundry
center
must
conform
with
local
codes
and
ordinances
and
the latest
edition
of the Nationa/Fue/
Gas Code ANS/Z223.
1/NFPA
54, or in Canada,
the
Canadian
Natural
Gas and Propane
Installation
Code.
CSA B 149. 1.
NOTE: The laundry
center
is designed
under
ANSI Z21.5.1
or ANSI/UL
2158-
CAN/CSA
C22.2 (latest
edition)
for
HOME
USE only.
This laundry
center
is not recommended
for commercial
applications
such as restaurants
or beauty salons, etc.
For your safety the information
in
this manuaI must be foIIowed to minimize the risk
of fire or expIosion or to prevent property damage,
personal injury or loss of life.
- Do not store or use gasoiine or other flammable
vapors and Iiquid in the vicinity of this or any
other appIiance.
- WHAT TO DO IF YOU SMELL GAS
® Do not try to light any appliance.
0 Do not touch any electrical switch; do not use
any phone in your building.
® Clear the room, building or area of all
occupants.
0 immediately
call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
® if you cannot reach your gas supplier, call the
fire department.
installation
and service must be preformed
by a
qualified
installer, service agency or the gas
supplier.
Contents
SUBJECT
PAGE
Pre-lnstallation Requirements
Electrical Requirements
Water Supply Requirements
Drain Requirements
Exhaust System Requirements
Gas Supply Requirements
Location
Mobile Home Installation
Rough-In Dimensions
Unpacking
Electrical Installation
Grounding Requirements
3 & 4-Wire Connections
Installation
Replacement Parts
2
2
2
2
3
4
4
4
5
5
6
6
7
7
8
Printed in U.S.A.
P/N134395100C (0408)
Advertisement
Table of Contents
Related Manuals for Frigidaire GCEH1642DS1
Summary of Contents for Frigidaire GCEH1642DS1
- Page 1 Tumble Action Laundry Center Gas & Electric Before beginning installation, carefully read these instructions. This will simplify the installation and ensure the laundry center is installed correctly and safely. Leave these instructions near laundry center after installation for future reference. NOTE: The electrical service...
-
Page 2: Pre-Installation
POWER SUPPLY CORD -The gas laundry center is equipped PRE-INSTALLATION REQUIREMENTS with a 120 volt 3-wire power cord. Tools and Materials Required for Installation: OUTLETRECEPTACLE- Properly grounded 3-prong receptacle 1. Phillips head screwdriver to be located so the power supply cord is accessible when the 2. -
Page 3: Exhaust System Requirements
EXHAUST SYSTEM REQUIREMENTS The maximum length of the exhaust system depends Use only 4 inch (10=16 cm) diameter <minimum) rigid or upon the type of duct used, number of elbows and type flexible metal duct and approved vent hood which has a of exhaust hood. -
Page 4: Gas Supply
GAS SUPPLY REQUIREMENTS 5. The following illustrations show minimum clearance dimensions and air openings for proper operation in a recess 1. Installation MUSTconform with local codes, or in the or closet installation. absence of local codes, with the National Fuel Gas 0 IN. -
Page 5: Rough-In Dimensions
ROUGH-IN DIMENSIONS 25_ iN. (64.13 CM) 2 _/_IN. (6.35 cM) 47" 16_/4IN. (41.27 CM) GAS8JFFLY 1 7/8 IN. \\\\ 5 Y4IN. (4.76 OM) (13.33 CM) (191.14 CM. O_gNNECTION 421/4IN. 351N. (107.32 CM.) 751/4IN. (91.44 CM.) WA%R INLEIS 31/_1N. 53 raN. 134.62 CM.) (7.94 CM.) 401/2IN. - Page 6 ELECTRICAL INSTALLATION ELECTRICLaundry Centers Laundry Canadian ELECTRIC Center The following are specific requirements Improper connection of the equipment for proper and safe electrical installation of your laundry grounding conductor can result in a risk of electrical shock, Check center. Failure to follow these instructions can create...
-
Page 7: Installation
1. Remove the screw securing the 2. The laundry center is equipped with a three-prong terminal block access cover to the (grounding) plug for your protection against shock hazard rear panel and remove cover. and should be plugged directly into a properly grounded 2. - Page 8 10. Connect the exhaust duct to outside duct work. Use GAS CONNECTION (Gaslaundry centers only) a. Remove the shipping cap from gas pipe at the rear of the duct tape to seal all joints. dryen 11. Plug the power cord into a grounded outlet. NOTE: DO NOT connect the laundry center to LR gas NOTE: Check to ensure the power is off at a circuit service without converting the gas valve.