Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Husqvarna 1153179-95
Summary of Contents for Husqvarna 1153179-95
- Page 1 Operator’s manual 357XP/XPG, 357XP E-tech 357XPG E-tech 359/G, 359 E-tech, 359G E-tech Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. E E E E n n n n g g g g l l l l i i i i s s s s h h h h...
-
Page 2: Key To Symbols
Symbols on the machine: WARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. - Page 3 KEY TO SYMBOLS The chain brake must be engaged when the chain saw is started. WARNING! Kickback may occur when the nose or tip of the guide bar touches an object, and cause a lightning fast reverse reaction, kicking the guide bar up and towards the operator.
-
Page 4: Table Of Contents
Contents KEY TO SYMBOLS Symbols on the machine: ... 2 Symbols in the operator’s manual: ... 2 CONTENTS Contents ... 4 INTRODUCTION Dear customer! ... 5 WHAT IS WHAT? What is what on the chain saw? ... 6 GENERAL SAFETY PRECAUTIONS Before using a new chain saw ... -
Page 5: Introduction
Dear customer! Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. -
Page 6: What Is What
What is what on the chain saw? Cylinder cover Front handle Chain brake and front hand guard Starter Chain oil tank Starter handle Adjuster screws carburetor Choke control/Start throttle lock Rear handle 10 Stop switch (Ignition on/off switch.) 11 Fuel tank 12 Muffler 13 Bar tip sprocket 14 Chain... -
Page 7: General Safety Precautions
GENERAL SAFETY PRECAUTIONS Before using a new chain saw • Please read this manual carefully. • Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly. • Refuel and start the chain saw. See the instructions under the headings Fuel Handling and Starting and Stopping. -
Page 8: Always Use Common Sense
GENERAL SAFETY PRECAUTIONS Always use common sense It is not possible to cover every conceivable situation you can face when using a chain saw. Always exercise care and use your common sense. Avoid all situations which you consider to be beyond your capability. If you still feel uncertain about operating procedures after reading these instructions, you should consult an expert before continuing. - Page 9 GENERAL SAFETY PRECAUTIONS Take care when using your saw and make sure the kickback zone of the bar never touches any object. • The chain brake (A) can either be activated manually (by your left hand) or automatically by the inertia release mechanism.
-
Page 10: Chain Catcher
GENERAL SAFETY PRECAUTIONS be activated manually by the movement of your left hand. • In the felling position the left hand is in a position that makes manual activation of the chain brake impossible. With this type of grip, that is when the left hand is placed so that it cannot affect the movement of the front hand guard, the chain brake can only be activated by the inertia action. -
Page 11: Cutting Equipment
GENERAL SAFETY PRECAUTIONS Vibration damping system Your machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier. The machine′s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and the machine′s handle unit. The body of the chain saw, including the cutting equipment, is insulated from the handles by vibration damping units. - Page 12 To maintain the safety features of the cutting equipment, you should replace a worn or damaged bar or chain with a bar and chain combinations recommended by Husqvarna. See instructions under the heading Technical Data for a list of replacement bar and chain combinations we recommend.
-
Page 13: Sharpening Your Chain And Adjusting Depth Gauge Setting
GENERAL SAFETY PRECAUTIONS Chain • Chain pitch (inches) • Drive link width (mm/inches) • Number of drive links. Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teeth • Never use a blunt chain. When the chain is blunt you have to exert more pressure to force the bar through the wood and the chips will be very small. -
Page 14: Tensioning The Chain
GENERAL SAFETY PRECAUTIONS • Check that the chain is correctly tensioned. A slack chain will move sideways, making it more difficult to sharpen correctly. • Always file cutting teeth from the inside face. Reduce the pressure on the return stroke. File all the teeth on one side first, then turn the chain saw and file the teeth on the other side. -
Page 15: Lubricating Cutting Equipment
GENERAL SAFETY PRECAUTIONS combination spanner. Tighten the chain until it does not sag from the underside of the bar. • Use the combination spanner to tighten the bar nuts while lifting the tip of the bar at the same time. Check that you can pull the chain round freely by hand and that it does not sag from the underside of the bar. - Page 16 GENERAL SAFETY PRECAUTIONS Chain drive sprocket The clutch drum is fitted with one of the following drive sprockets: A Spur sprocket (the chain sprocket is welded on the drum) B Rim sprocket (replaceable) Regularly check the degree of wear on the drive sprocket. Replace if wear is excessive.
-
Page 17: Assembly
Fitting the bar and chain WARNING! Always wear gloves, when working with the chain. Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle. Remove the bar nuts and remove the clutch cover (chain brake). -
Page 18: Fuel Handling
When working with continuous high revs (e.g. limbing) a higher octane is recommended. Environment fuel HUSQVARNA recommends the use of alkylate fuel or environmental fuel for four-stroke engines blended with two-stroke oil as set out below. Note that carburetor adjustment may be necessary when changing the type of fuel (see instructions under the heading Carburetor). -
Page 19: Fueling
• In temperatures below 32°F (0°C) some oils become too viscous. This can overload the oil pump and result in damage to the oil pump components. • Contact your service agent when choosing chain oil. Fueling WARNING! Taking the following precautions, will lessen the risk of fire: Do not smoke and do not place any hot objects in the vicinity of fuel. -
Page 20: Starting And Stopping
Starting and stopping WARNING! Note the following before starting: The chain brake must be engaged when the chain saw is started to reduce the chance of contact with the moving chain during starting. Never start a chain saw unless the bar, chain and all covers are fitted correctly. - Page 21 As the chain brake is still activated the engine must return to idling speed as soon as possible by disengaging the throttle latch in order to avoid unnecessery wear on the clutch assembly. Note! Pull the front hand guard towards the front handle. The chain brake is now disengaged.
-
Page 22: Working Techniques
Before use: Check that the chain brake works correctly and is not damaged. Check that the rear right hand guard is not damaged. Check that the throttle lockout works correctly and is not damaged. Check that the stop switch works correctly and is not damaged. -
Page 23: General Rules
cause you to lose control. Both situations can cause serious personal injury. Before moving your chain saw switch off the engine and lock the chain using the chain brake. Carry the chain saw with the bar and chain pointing backwards. Fit a guard to the bar before transporting the chain saw or carrying it for any distance. -
Page 24: Basic Cutting Technique
In order to keep control of your saw, always maintain a firm foothold. Never work on a ladder, in a tree or on any other insecure support. Always use a fast cutting speed, i.e. full throttle. Take great care when you cut with the top edge of the bar, i.e. - Page 25 Is there a risk of kickback? Do the conditions and surrounding terrain affect how safely you can stand and move about? Two factors decide whether the chain will jam or the object that you are cutting will split: the first is how the object is supported before and after cutting, and the second is whether it is in tension.
-
Page 26: Tree Felling Technique
Finish by cutting from below so that the two cuts meet. Tree felling technique IMPORTANT! It takes a lot of experience to fell a tree. Inexperienced users of chain saws should not fell trees. Do not attempt any task beyond your experience level! Safe distance The safe distance between a tree that is to be felled and anyone else working nearby is at least 2 1/2 tree lengths. - Page 27 starts to fall. Your path of retreat should be roughly 135 degrees away from the intended felling direction. Retreat path Felling WARNING! Unless you have special training we advise you not to fell trees with a diameter larger than the bar length of your saw! Felling is done using three cuts.
-
Page 28: Freeing A Tree That Has Fallen Badly
When the felling cut and directional cut are complete the tree should start to fall by itself or with the aid of a felling wedge or breaking bar. We recommend that you use a bar that is longer than the diameter of the tree, so that you can make the felling cut and directional cuts with single cutting strokes. -
Page 29: How To Avoid Kickback
Cut tree/limb from outside the bend, after tension has been released. How to avoid kickback WARNING! Kickback can happen very suddenly and violently; kicking the chain saw, bar and chain back at the user. If this happens when the chain is moving it can cause very serious, even fatal injuries. -
Page 30: Maintenance
These limit the adjustment possibilities to a maximum of a 1/2 turn. Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. Function •... -
Page 31: Checking, Maintaining And Servicing Chain Saw Safety Equipment
WARNING! Contact your servicing dealer, if the idle speed setting cannot be adjusted so that the chain stops at idle. Do not use the chain saw until it has been properly adjusted or repaired. High speed jet H At the factory the engine is adjusted at sea level. When working at a high altitude or in different weather conditions, temperatures and atmospheric humidity, it may be necessary to make minor... -
Page 32: Throttle Lockout
Checking the brake trigger Place the chain saw on firm ground and start it. Make sure the chain does not touch the ground or any other object. See the instructions under the heading Start and stop. Grasp the chain saw firmly, wrapping your fingers and thumbs around the handles. -
Page 33: Muffler
Vibration damping system Regularly check the vibration damping units for cracks or deformation. Make sure the vibration damping units are securely attached to the engine unit and handle unit. Stop switch Start the engine and make sure the engine stops when you move the stop switch to the stop setting. -
Page 34: Starter
Starter WARNING! When the recoil spring is wound up in the starter housing it is under tension and can, if handled carelessly, pop out and cause personal injury. Care must be exercised when replacing the return spring or the starter cord. Wear protective glasses and protective gloves. -
Page 35: Air Filter
A damaged air filter must always be replaced. A HUSQVARNA chain saw can be equipped with different types of air filters according to working conditions, weather, season, etc. Contact your dealer for advice. -
Page 36: Lubricating The Bar Tip Sprocket
Lubricating the bar tip sprocket Lubricate the bar tip sprocket each time you refuel. Use the special grease gun and a good quality bearing grease. Needle bearing lubrication The clutch drum has a needle bearing on the output shaft. This needle bearing must be lubricated regularly (once a week). -
Page 37: Air Injection" Centrifugal Cleaning
because the higher exhaust temperature requires efficient cooling of the engine and the catalytic converter unit. ”Air Injection” centrifugal cleaning Centrifugal cleaning means the following: All air to the carburetor passes through the starter. Dirt and dust is pushed out by the cooling fan. IMPORTANT! In order to maintain operation of the centrifugal cleaning system it must be regularly maintained. -
Page 38: Maintenance Schedule
Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. Daily maintenance Clean the outside of the machine. Check that the components of the throttle control work safely. -
Page 39: Technical Data
Technical data Motor Cylinder displacement, cu.in/cm Cylinder bore, inch/mm Stroke, inch/mm Idle speed, rpm Power, kW/ rpm Ignition system Spark plug Electrode gap, inch/mm Fuel and lubrication system Fuel tank capacity, US pint/litre Oil pump capacity at 9,000 rpm, ml/min Oil tank capacity, US pint/litre Type of oil pump Weight... -
Page 40: Bar And Chain Combinations
Chain saw models Husqvarna 357XP and 359 met the kickback performance requirements of ANSI B 175.1-2000 when tested with the combinations of bars and saw chains listed below. The saw chain Husqvarna H30 is also classified as a low kickback saw chain since it met the requirements for low kickback saw chain outlined in ANSI B 175.1-2000. -
Page 41: Saw Chain Filing And File Gauges
Technical data Saw chain filing and file gauges English – 41... -
Page 42: Federal Emission Control Warranty Statement Your Warranty Rights And Obligations
REPAIR OR REPLACEMENT OF PARTS Repair or replacement of any warranted part will be performed at no 42 – English charge to the owner at an approved Husqvarna Forest & Garden servicing dealer. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Husqvarna Forest &... -
Page 43: American Standard Safety Precautions
AMERICAN STANDARD SAFETY PRECAUTIONS Safety precautions for chain saw users (ANSI B175.1-2000 Annex C) Kickback safety precautions WARNING! Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. - Page 44 Original instructions 1153179-95 ´®z+U1•¶50¨ ´®z+U1•¶50¨ 2010-01-26...