Related Manuals for Husqvarna 346XP/ 351
Summary of Contents for Husqvarna 346XP/ 351
- Page 1 Oper ator’s manual (EPA I, EPA II) 346XP 353 Please r ead the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h understand the instructions before using the machine.
-
Page 2: Key To Symbols
Symbols on the machine: WARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Always wear: •... -
Page 3: Table Of Contents
Contents KEY TO SYMBOLS Symbols on the machine: ... Symbols in the operator’s manual: ... CONTENTS Contents ... INTR ODUCTION Dear customer! ... WHA T IS WHAT? What is what on the chain sa w? ... GENERAL SAFETY PRECA UTIONS Bef ore using a new chain saw ... -
Page 4: Intr Oduction
Dear customer! Cong ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant. -
Page 5: Wha T Is What
Husqvarna XXX XXXX XXXXXXX Husqvarna AB Huskvarna, SWEDEN What is what on the c hain saw? 1 Cylinder cover 2 Front handle 3 Chain brake and front hand guard 4 Starter 5 Chain oil tank 6 Starter handle 7 Adjuster screws carburetor... -
Page 6: General Safety Preca Utions
GENERAL SAFETY PRECA UTIONS Bef ore using a new chain saw • Please read this manual carefully. • Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly. • Refuel and start the chain saw. See the instructions under the headings Fuel Handling and Starting and Stopping. -
Page 7: Personal Protective Equipment
GENERAL SAFETY PRECA UTIONS chain sa w usage if possible. Your dealer, forestry school or your library can provide information about which training materials and courses are available. Work is constantly in progress to improve the design and technology - improvements that increase your safety and efficiency. - Page 8 GENERAL SAFETY PRECA UTIONS • The chain brake (A) can either be activated manually (by your left hand) or automatically by the inertia release mechanism. • The brake is applied when the front hand guard (B) is pushed forwards. • This movement activates a spring-loaded mechanism that tightens the brake band (C) around the engine drive system (D) (clutch drum).
- Page 9 GENERAL SAFETY PRECAUTIONS Will my hand always activate the chain brake during a kickback? No. It takes a certain force to move the hand guard forward. If your hand only lightly touches the front guard or slips over it, the force may not be enough to trigger the chain brake. You should also maintain a firm grip of the chain saw handles while working.
-
Page 10: Cutting Equipment
GENERAL SAFETY PRECAUTIONS Cutting hardwoods (most broadleaf trees) creates more vibration than cutting softwoods (most conifers). Cutting with cutting equipment that is blunt or faulty (wrong type or badly sharpened) will increase the vibration level. WARNING! Overexposure to vibration can lead to circulatory damage or nerve damage in people who have impaired circulation. -
Page 11: Sharpening Your Chain And Adjusting Depth Gauge Setting
To maintain the safety features of the cutting equipment, you should replace a worn or damaged bar or chain with a bar and chain combinations recommended by Husqvarna. See instructions under the heading Technical Data for a list of replacement bar and chain combinations we recommend. -
Page 12: Sharpening/Adjusting Depth Gauge Setting
GENERAL SAFETY PRECAUTIONS • The cutting part of the chain is called the cutter and consists of a cutting tooth (A) and the depth gauge (B). The cutters cutting depth is determined by the difference in height between the two (depth gauge setting). When you sharpen a cutting tooth there are four important factors to remember. -
Page 13: Lubricating Cutting Equipment
GENERAL SAFETY PRECAUTIONS Adjustment of depth gauge setting • The cutting teeth should be newly sharpened before adjusting the depth gauge setting. We recommend that you adjust the depth gauge setting every third time you sharpen the cutting teeth. NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively. - Page 14 GENERAL SAFETY PRECAUTIONS Filling with chain oil • All our chain saws have an automatic chain lubrication system. On some models the oil flow is also adjustable. • The saw chain oil tank and the fuel tank are designed so that the fuel runs out before the saw chain oil.
- Page 15 GENERAL SAFETY PRECAUTIONS When the length of the cutting teeth has worn down to only 4 mm (0,16 inch) the chain must be replaced. Check regularly: • Whether there are burrs on the edges of the bar. Remove these with a file if necessary. •...
-
Page 16: Assembly
Fitting the bar and chain WARNING! Always wear gloves, when working with the chain, in order to protect your hands from injury. Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle. Remove the bar nuts and remove the clutch cover (chain brake). -
Page 17: Fuel Handling
When working with continuous high revs (e.g. limbing) a higher octane is recommended. Environment fuel HUSQVARNA recommends the use of alkylate fuel or environmental fuel for four-stroke engines blended with two- stroke oil as set out below. Note that carburetor adjustment may be necessary when changing the type of fuel (see instructions under the heading Carburetor). -
Page 18: Fueling
• In temperatures below 0°C (32°F) some oils become too viscous. This can overload the oil pump and result in damage to the oil pump components. • Contact your service agent when choosing chain oil. Fueling WARNING! Taking the following precautions, will lessen the risk of fire: Do not smoke and do not place any hot objects in the vicinity of fuel. -
Page 19: Starting And Stopping
STARTING AND STOPPING Starting and stopping WARNING! Note the following before starting: The chain brake must be engaged when the chain saw is started to reduce the chance of contact with the moving chain during starting. Never start a chain saw unless the bar, chain and all covers are fitted correctly. -
Page 20: Starting And Stopping
STARTING AND STOPPING Note! Pull the front hand guard towards the front handle. The chain brake is now disengaged. Your saw is ready for use. WARNING! Long term inhalation of the engine’s exhaust fumes, chain oil mist and dust from sawdust can represent a health risk. -
Page 21: Working Techniques
Before use: 1 Check that the chain brake works correctly and is not damaged. 2 Check that the rear right hand guard is not damaged. 3 Check that the throttle lock works correctly and is not damaged. 4 Check that the stop switch works correctly and is not damaged. -
Page 22: General Rules
6 Before moving your chain saw switch off the engine and lock the chain using the chain brake. Carry the chain saw with the bar and chain pointing backwards. Fit a guard to the bar before transporting the chain saw or carrying it for any distance. -
Page 23: Basic Cutting Technique
Cutting with the bottom edge of the bar, i.e. from the top of the object downwards, is known as cutting with a pulling chain. In this case the chain saw pulls itself towards the tree and the front edge of the chain saw body rests naturally on the trunk when cutting. -
Page 24: Tree Felling Technique
Cutting WARNING! Never attempt to cut logs while they are in a pile or when a couple of logs are lying together. Such procedures drastically increase the risk of kickback which can result in a serious or fatal injury. If you have a pile of logs, each log you attempt to cut should be removed from the pile, placed on a saw horse or runners and cut individually. - Page 25 Felling direction The aim is to fell the tree in a position where you can limb and cross-cut the log as easily as possible. You want it to fall in a location where you can stand and move about safely. Once you have decided which way you want the tree to fall you must judge which way the tree would fall naturally.
- Page 26 Next make the bottom cut so that it finishes exactly at the end of the top cut. The directional cuts should run 1/4 of the diameter through the trunk and the angle between the top cut and bottom cut should be 45°. The line where the two cuts meet is called the directional cut line.
-
Page 27: Freeing A Tree That Has Fallen Badly
We recommend that you use a bar that is longer than the diameter of the tree, so that you can make the felling cut and directional cuts with single cutting strokes. See instructions under the heading Technical data section to find out which lengths of bar are recommended for your saw. -
Page 28: How To Avoid Kickback
How to avoid kickback WARNING! Kickback can happen very suddenly and violently; kicking the chain saw, bar and chain back at the user. If this happens when the chain is moving it can cause very serious, even fatal injuries. It is vital you understand what causes kickback and that you can avoid it by taking care and using the right working technique. -
Page 29: Maintenance
Due to existing environmental and emissions legislation your chain saw is equipped with movement limiters on the carburetor adjuster screws. These limit the adjustment possibilities to a maximum of a 1/2 turn. Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. Function •... -
Page 30: Checking, Maintaining And Servicing Chain Saw Safety Equipment
When test run at the factory, the high speed jet is set so that the engine satisfies the applicable legal requirements at the same time as achieving maximum performance. The carburetor’s high speed jet is then locked using a limiter cap in the fully screwed out position. -
Page 31: Right Hand Guard
Apply full throttle and activate the chain brake by tilting your left wrist forward onto the front hand guard. Do not let go of the front handle. The chain should stop immediately. Throttle lock • Make sure the throttle control is locked at the idle setting when the throttle lock is released. -
Page 32: Muffler
Muffler Never use a machine that has a faulty muffler. Regularly check that the muffler is securely attached to the machine. Some mufflers are equipped with a special spark arrestor mesh. If your machine has this type of muffler, you should clean the mesh at least once a week. -
Page 33: Air Filter
The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced. A HUSQVARNA chain saw can be equipped with different types of air filters according to working conditions, weather, season, etc. Contact your dealer for advice. -
Page 34: Spark Plug
Spark plug The spark plug condition is influenced by: • Incorrect carburetor adjustment. • An incorrect fuel mixture (too much or incorrect type of oil). • A dirty air filter. These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties. -
Page 35: Air Injection" Centrifugal Cleaning
Note! The cooling system on a chain saw with catalytic converter must be cleaned daily. This is particularly important on chain saws with catalytic converters, because the higher exhaust temperature requires efficient cooling of the engine and the catalytic converter unit. ”Air Injection”... -
Page 36: Maintenance Schedule
Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. Daily maintenance Clean the outside of the machine. Check that the components of the throttle control work safely. -
Page 37: Technical Data
Technical data Engine Cylinder displacement, cu.in/cm Cylinder bore, inch/mm Stroke, inch/mm Idle speed, rpm Power, kW/hp @ rpm Ignition system Manufacturer of ignition system Type of ignition system Spark plug Electrode gap, inch/mm Fuel and lubrication system Manufacturer of carburetor Carburetor type Fuel tank capacity, US pint/litre Oil pump capacity at 9,000 rpm, ml/min... -
Page 38: Bar And Chain Combinations
Chain saw models Husqvarna 346XP and 353 met the kickback performance requirements of ANSI B 175.1-2000 when tested with the combinations of bars and saw chains listed below. The saw chain Husqvarna H30 is also classified as a low kickback saw chain since it met the requirements for low kickback saw chain outlined in ANSI B 175.1-2000. -
Page 39: Federal Emission Control Warranty Statement
The warranty period begins on the date small nonroad engine is delivered. LENGTH OF COVERAGE Husqvarna Forest & Garden warrants to the initial owner and each subsequent purchaser that the engine is free from defects in materials and workmanship which cause the failure of a warranted part for a period of two years. -
Page 40: American Standard Safety Precautions
AMERICAN STANDARD SAFETY PRECAUTIONS Safety precautions for chain saw users (ANSI B 175.1-2000 Annex C) Kickback safety precautions WARNING! Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. - Page 42 ´®z+R$o¶59¨ ´®z+R$o¶59¨...
- Page 44 1150047-95 ´®z+R$o¶59¨ ´®z+R$o¶59¨ 2005-01-13...