Related Manuals for Honeywell 720P
Summary of Contents for Honeywell 720P
- Page 1 Honeywell 720P&D1 IR Vari-Focal Bullet Camera User’s Manual Document 800-14747 Rev. A...
- Page 3 Honeywell Owner's Record The model and serial numbers are located at the bottom of device. Record these numbers in the spaces provided below. Refer to these numbers whenever you call upon your dealer regarding this product. Model No. ____________________ Serial No. ____________________ To prevent fire or shock hazard, do not expose the unit to rain or moisture.
-
Page 4: Declaration Of Conformity
Honeywell Declaration of Conformity This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause... -
Page 5: Table Of Contents
Honeywell Contents Overview ............................ 1 Introduction ..........................1 Features ............................. 1 Minimum System Requirements ....................2 Package Contents ........................3 Connections ..........................4 Hardware Installation ........................ 7 How to adjust zoom/focus of lens .................... 8 Preparation ..........................9 Search and Set up by IP Wizard ....................9 Search .......................... - Page 6 Honeywell System Setting .......................... 22 Network: Configure Network settings .................. 22 Camera: Adjust Camera parameters ................... 33 System: Configure and maintain system ................39 Video: Configure OSD, Overlay, Profile, and ROI ..............43 Audio: Audio parameters ..................... 48 User: Manage user name, password and login privilege ............48 E-Mail: Setup E-Mail configuration ..................
-
Page 7: Overview
PC. The live video can be uploaded to a website for the world to see. Features Sony Exmor™ image sensor 720P : 720p / 1.3 Mega mode ; SVGA/D1 : 800x600 / D1 mode 720P : 60fps in all resolutions ; SVGA/D1: 30fps in all resolution ONVIF compliant... -
Page 8: Minimum System Requirements
Overview UPnP device discovery and NAT router transversal for easy installation Dynamic IP Service, DIPS®, to search your IP camera from Internet easily H.264, MPEG4 and MJPEG triple compression simultaneously 12-profile encoder simultaneously UDP / TCP / HTTP / HTTPS protocols selectable Event and Continuous recording to SD card or SAMBA server External microphone input Audio line out... -
Page 9: Package Contents
Honeywell 2. Package Contents User can find the following items in the package: Item Descriptions 1. IR Network Camera is the main element of the product. 2. Switching Power Supply Convert AC/DC 24V to DC 12V for camera 3. User’s Manual CD provides installation software, application program, important information and instructions for operating the Network Camera. -
Page 10: Connections
Connections 3. Connections RJ45 LAN socket: Connect to PC or Hub/Switch. It’s for connections to 10Base-T Ethernet, 100Base-TX, or 1000Base-TX Ethernet cabling. This Ethernet port built N-Way protocol can detect or negotiate the transmission speed of the network automatically. Please use Category 5 or better cable to connect the Network Camera to an Ethernet network switch or hub. - Page 11 Honeywell This LED will be flashing while network accessing via Ethernet. Power LED (orange color) This LED is used to indicate whether DC power is on or not. RS-485: Connect to a local keyboard controller. DI/ DO: Connect to sensor in and alarm out devices...
- Page 12 Connections The Network Camera also provides composite video output. The video output function is only for easy installation to check view angle and focus. The output is not a Mega-pixel resolution. Furthermore, the video output is off by default. To turn on video, please refer to Setting\Camera\Picture chapter.
-
Page 13: Hardware Installation
Honeywell 4. Hardware Installation Fix IR camera to desired location with stand Plug-in Ethernet Cable into LAN port Connect an Ethernet cable to the RJ45 connector. Connect RS485 D+ and D- (if you need to control PT scanner) Connect the attached power adapter to camera and plug-in this adapter into... -
Page 14: How To Adjust Zoom/Focus Of Lens
How to Adjust Zoom/Focus of Lens 5. How to Adjust Zoom/Focus of Lens Zoom stick Focus stick Open the back cover of the camera Adjust zoom stick first Adjust focus stick to get clear image Close the back cover of the camera tightly. Otherwise, the camera may fail to waterproof. -
Page 15: Preparation
Honeywell 6. Preparation Search and Set up by IP Wizard Once you installed the Camera on a LAN environment, you have two easy ways to search your Cameras by IP Wizard II or UPnP™ discovery. Here is the way to execute IP Wizard II to discover Camera’s IP address and set up related parameter in a Camera. -
Page 16: View
Preparation View If IPWizard II finds network devices, View button will be available. Please select the device you want to view and click the View button. Then you could see the video from camera directly. Furthermore you could double click the left button of mouse to link to the network device by web browser. -
Page 17: Lan
Honeywell In case you want to change the IP related parameters of wired interface, please select the device you want to configure and click the LAN button. Relative settings will be carried out as below. You could modify the relative settings of the selected device. Click “<<” button will quit the LAN setting procedure and click “>>”... -
Page 18: Wireless
Preparation If you like to change username and/or password of the device, just click the check button. Then, the related fields will show up as below. After keying in new username and password, click “Submit” button to perform your setting accordingly. -
Page 19: Install The Device Behind A Nat Router
Honeywell Click the targeted Device. Then Internet Explorer will connect to this Network Camera automatically. Install the Device behind a NAT Router Once installed, the device is accessible on your LAN. To access the device from the Internet you must configure your broadband router to allow incoming data traffic to the device. If the device is installed on the LAN with a router, then it may get a dynamic IP address from the DHCP server. -
Page 20: Access The Device From The Internet Explorer For The First Time
Preparation Access your Network Camera by DIPS Refer to Setting System System page for detail DIPS information. Access the device from the Internet Explorer for the first time If it’s the first you want to access your Network Camera by Windows PC, it would strongly recommend you to use Internet Explorer as default browser as possible. -
Page 21: Logging In As An Viewer
Honeywell According your browser’s security setting, the IE Web Page may prompt the “Security Warning” window. If so, select “Yes” to install and run the ActiveX control into your PC. Otherwise, the system will load the ActiveX silently. After the ActiveX control was installed and ran, the first image will be displayed. -
Page 22: Operating The Network Camera
Operating the Network Camera 7. Operating the Network Camera Start-up screen will be as follow no matter an ordinary users or an administrator. ActiveX Control Monitor Image Section 2-Way Full Audio Screen Monitor Image Section The image shot by the device is shown here. The date and time are displayed at the top of the window if Text Overlay enabled. -
Page 23: Video Profile
Honeywell Video Profile The device supports multi-profile function for H.264, MEPG4 and MJPEG simultaneously. User can chose the proper and/or preferred profile which is listed here. Streaming Protocol User can select proper streaming protocol according to networking environment. Language The device could provide multiple languages to meet customer’s requirement. -
Page 24: Ptz Control
Operating the Network Camera PTZ Control Note that this function is enabled by “camera protocol” been set first. Click to display the following control panel: Camera direction Camera speed Preset Go tour Tour Auto pan Camera direction: Control camera up/down/left/right and home position. Camera speed: Choose the speed of Pan and Tilt. -
Page 25: Activex Control
Honeywell ActiveX Control The plug-in ActiveX control supports a lot of functions by clicking the left mouse button. Note that this feature only supports on the ActiveX control within Microsoft® Internet Explorer. On the ActiveX control icon, click the Left Mouse Button, then a menu pop-up. This menu provides features that are unique to the ActiveX control. -
Page 26: Snapshot
Operating the Network Camera Click Digital Zoom to active this function as above. User can drag or scale the box over the video to adjust zoom ratio and position. Snapshot Click Snapshot to activate this function. Press Snapshot button to take a picture. The image file is saved as JPEG format into your local PC. -
Page 27: Volume
Honeywell Volume Click Volume to activate this function. There are two control bars for speaker and microphone volume respectively. Scroll these control bars to adjust the audio attribute. Check the volume mute will mute the speaker output. About Click About to show this ActiveX information. -
Page 28: Administrating The Device
Administrating the Device 8. Administrating the Device System Setting This function is only available for user logged into Camera as administrator. Click on each menu name to display its setting page. Item Action Configure Network settings such as DHCP, DDNS, RTSP, PPPoE Network and UPnP Camera... - Page 29 Honeywell MAC address Displays the Ethernet MAC address of the device. Note that user can not modify it. Obtain IP address automatically (DHCP) DHCP: Stands for Dynamic Host Configuration Protocol. Enable this checked box when a DHCP server is installed on the network to issue IP address assignment.
- Page 30 Administrating the Device Therefore, the user can access the device by either http://xx.xx.xx.xx/, or http://xx.xx.xx.xx:xxxx/ to access the device. If multiple devices are installed on the LAN and also required to be accessed from the WAN, then the HTTP Port can be assigned as the virtual server port mapping to support multiple devices.
-
Page 31: Ddns Service
Honeywell HTTPS To enable or disable the HTTPS service here. Note that the HTTPS function of this device is not only encrypted the web content but also audio/video data. If the HTTPS is enabled, there is further option for “HTTP&HTTPS” or “HTTPS only”. In case, the “HTTPS only”... - Page 32 Administrating the Device DDNS To enable or disable the DDNS service here. Server name Choose one of the built-in DDNS servers. DDNSHost The domain name is applied of this device. User name The user name is used to log into DDNS. Password The password is used to log into DDNS.
- Page 33 Honeywell Connect to a LAN by DHCP or Fixed IP • Access the device, enter Setting Network PPPoE as below • PPPoE To enable or disable the PPPoE service here. User name Type the user name for the PPPoE service which is provided by the ISP.
- Page 34 Administrating the Device RTSP Port Choose the RTSP port. The RTSP protocol allows a connecting client to start a video stream. Enter the RTSP port number to use. The default value is 554. RTP Port Specify the range of transmission port number of video stream. The default range is 50000 to 50999.
- Page 35 Honeywell UPnP is short for Universal Plug and Play, which is a networking architecture that provides compatibility among networking equipment, software, and peripherals. This device is an UPnP enabled Network Camera. If your operating system is UPnP enabled, the device will automatically be detected and a new icon will be added to “My Network Places.”...
- Page 36 Administrating the Device Bonjour To enable or disable the Bonjour service here. Friendly Name To show the friendly name of this device here. IP Filter You can enter different user’s IP address which are allowing enter or denying by the device. IP Filter To enable or disable the IP filter function here.
- Page 37 Honeywell IP Notification In case the IP address is changed, system is able to send out an email to alert someone if the function is enabled. SMTP Notification (e-mail) If enable this function, then the “Send to“ and “Subject” fields need to be filled.
- Page 38 Administrating the Device TCP Server Type the server name or the IP address of the TCP server. TCP Port Set port number of TCP server. Message The message will be sent to FTP server. HTTP Notification If enable this function, then the fields below need to be filled. Type the server name or the IP address of the HTTP server.
-
Page 39: Camera: Adjust Camera Parameters
Honeywell Proxy Login name Type the user name for the HTTP Proxy. Proxy Login Password Type the password for the HTTP Proxy. Custom parameter User can set specific parameters to HTTP server. Message The message will be sent to HTTP server. - Page 40 Administrating the Device White Balance Auto: will adjust the white balance automatically. Hold: will hold the white balance. Iris/Exposure Control Auto Iris: will adjust the DC Iris automatically. This Camera is built-in a DC-Iris lens. In case, the “Auto Iris” mode is selected, the Camera will control DC Iris automatically.
- Page 41 Honeywell Exposure Value Exposure value is AE target value. This value is to adjust the integration, analog gain and digital gain to achieve the target brightness value (Exposure Value). This value is dependent to “Auto Exposure” only. Color Level Large value will be colorful.
-
Page 42: Privacy Mask
Administrating the Device This function is to provide clear images even under back light circumstances. The higher “Strength” level will adjust contrast compensation stronger. Default Settings Restore to factory image settings. Privacy Mask Use this page to specify privacy mask window 1 to window 8 and set the name and gray level for selected window. -
Page 43: Preset Setting
Honeywell This device can connect to a PTZ camera or speed dome camera and controls them thru RS485 interface. Camera Address This is the camera ID set in PTZ camera or speed dome camera. Note that please DO NOT change the default value if unnecessary. If so, user needs to check and set value properly for both sides. -
Page 44: Tour Setting
Administrating the Device Tour Setting Up to 128 positions can be preset, and the camera can be programming to move to the preset position sequentially. Tour Name The group name of the sequence of camera tour. The maximum number of camera tour is Running Enable or disable this camera tour. -
Page 45: System: Configure And Maintain System
Honeywell Preset Set the sequence of the tour. Maximum 16 points can be assigned. The selected preset position is added in the Sequence list from 1 to 16. Wait Time Type a period of time during which the camera is to stay at each preset point, between 0 to 36000 seconds. - Page 46 Administrating the Device User can check the system log information of the device, including the Main Info, Appended Info, Operator IP, and so on … Reload Click this button; user can refresh the log information of the device. Date & Time You can setup the device or make it synchronized with PC or remote NTP server.
- Page 47 Honeywell Maintenance Hard Factory Default (Include the network setting) Recall the device hard factory default settings. Note that click this button will reset all device’s parameters to the factory settings (including the IP address). Factory Default (Except the network setting) The unit is restarted and most current settings are reset to factory default values.
- Page 48 Administrating the Device Firmware Upgrade The device supports new firmware upgrade (the software that controls the operation in the device). Please contact your dealer for the latest version if necessary. Download the latest firmware file from our website or your dealer. Unzip this firmware file to binary file and store it into your PC.
-
Page 49: Video: Configure Osd, Overlay, Profile, And Roi
Honeywell System Restart The device is restarted without changing any of the network settings. It means the IP address of the device will not change after firmware upgrade. Video : Configure OSD, Overlay, Profile, and ROI This device supports video resolution up to 1280x720 or 1280x1024. - Page 50 Administrating the Device In “User Defined Text” mode, user can overlay a text string onto camera image as below: The font style can be chosen in this page. Once the font type settled, click “Save” button to upload text to image. Coordinates Set position of image on the video.
- Page 51 Honeywell Resolution Size information of the uploaded bitmap file. Chroma Key (Background Color) Define the Chroma key of the uploaded bitmap file. Then user can set transparency of the bitmap. Transparency Lower value will lower transparent. Value 0 means opacity.
- Page 52 Administrating the Device Rate Control Defines the rate control method of this profile. There are three options: Constant Bit Rate (CBR), Variable Bit Rate (VBR), and Enhanced Variable Bit Rate (EVBR). For CBR, the video bit rate is between low to high bandwidth based on different resolutions. User can set the desired bit rate to match the limitation of bandwidth.
- Page 53 Honeywell Note that this function is not recommended for camera with PTZ/ePTZ actions. AOI means Area of Interest, Use this page to specify location and size of AOI windows. User can define maximum two ROI windows. And User can define image quality level -10 to 10...
-
Page 54: Audio: Audio Parameters
Administrating the Device Audio: Audio Parameters Audio: To enable or disable audio function Audio Type: To select audio codec Audio Mode: To select Simplex or Full duplex (2-way audio) mode Input Gain: To adjust gain of input audio Output Gain: To adjust gain of output audio User: Manage User Name, Password and Login Privilege Use this menu to add, update, or remove the usernames and passwords of the Administrator... - Page 55 Honeywell Viewer login Select “Anonymous” to allow any one viewing the video once connected. Otherwise, only users in database can view the video after login. Access Right Administrator can access every function in this device. However, Viewers only can view the video and access limited function.
- Page 56 Administrating the Device Protocol ONVIF To enable or disable the ONVIF interface here. And select the ONVIF version to match client’s supported version. ONVIF is a global and open industry forum with the goal to facilitate the development and use of a global open standard for the interface of physical IP-based security products. In IP products video surveillance other words, to create a standard for how...
-
Page 57: E-Mail: Setup E-Mail Configuration
Honeywell To enable or disable the SNMPv1 or SNMPv2c here. And set Read community and Write community. E-Mail: Setup E-Mail Configuration User may setup SMTP mail parameters for further operation of Event Schedule. That’s, if users want to send the alarm message out, it will need to configure parameters here first and also add at least one event schedule to enable event triggering. -
Page 58: Event Detection
Administrating the Device Type the user name for the SMTP server if Authentication is Enable. Authentication Password Type the password for the SMTP server if Authentication is Enable. E-mail From Type the sender’s E-mail address. This address is used for reply e-mails. E-mail To Type the receiver’s e-mail address. -
Page 59: Camera Tampering
Honeywell These windows can be specified as Included or Excluded type. Included windows target specific areas within the whole video image Excluded windows define areas within an Include window that should be ignored (areas outside Include windows are automatically ignored) Name Name of the specified motion window. -
Page 60: Storage: Status And Configuration Of Samba Server
Administrating the Device Audio Detection Audio detection alarm can be used as a complement to motion detection. Since audio detection can react to events in areas too dark for the video motion detection functionality to work properly. In addition, it can be used to detect activity in areas outside of the camera’s view. -
Page 61: Continuous Recording
Honeywell Host Type the SAMBA server domain name or the IP address of the SMTP server. Share Type the share folder of remote SAMBA server which the camera will upload files to this space. User name Type the user name for the remote SAMBA server. -
Page 62: Recording List: Files List Inside The Samba Server
Administrating the Device Continuous Recording Enable or disable this function. Record File Type Choose a video profile to record. DISK Save recorded files to remote SAMBA server. Path Define the folder path for the recorded files. Restart Be careful, click this button will delete all continuous files recorded in remote SAMBA server. Recording List: Files list inside the SAMBA Server Continuous Recording List This page only shows the continuous recording files which stored in remote SAMBA server. -
Page 63: Event Server: Setup Ftp/Tcp/Http/Samba Server Configuration
Honeywell Event Server: Setup FTP/TCP/HTTP/SAMBA Server Configuration FTP Server You may setup FTP parameters for further operation of Event Schedule. That’s, if users want to send the alarm message to an FTP server, it will need to configure parameters here and also add at least one event schedule to enable event triggering as SMTP. -
Page 64: Tcp Server
Administrating the Device User can specify multiple FTP paths as wish. Therefore, user needs to specify a name for each FTP setting. FTP Server Type the server name or the IP address of the FTP server. Test Check the FTP server whether this account is available or not. FTP Login name Type the user name for the FTP server. -
Page 65: Http Server
Honeywell Name User can specify multiple TCP servers as wish. Therefore, user needs to specify a name for each TCP server setting. TCP Server Type the server name or the IP address of the TCP server. TCP Port Set port number of TCP server. - Page 66 Administrating the Device Name User can specify multiple HTTP servers as wish. Therefore, user needs to specify a name for each HTTP server setting. Type the server name or the IP address of the HTTP server. Test Check the HTTP server whether it is available or not. HTTP Login name Type the user name for the HTTP server.
-
Page 67: Samba Server
Honeywell Proxy Port Set port number of Proxy. SAMBA Server The device also can send event recording video files to specified SAMBA server. Name User can specify multiple HTTP servers as wish. Therefore, user needs to specify a name for each HTTP server setting. -
Page 68: Event Schedule: Configure The Event Schedule
Administrating the Device Event Schedule: Configure the Event Schedule Setting This menu is used to specify the schedule of Event or Schedule Trigger and activate the some actions provided by this device. Where the Schedule Trigger will be activated by user-define interval without event happened. - Page 69 Honeywell Select event trigger 10. Enable time: start from 00:00 to 24:00 every day 11. Trigger by: Motion Area (Added in Object Detection page) 12. Action : Send FTP (Add in Event Server -> FTP Server page) Example 2 Send file to E-Mail server by motion triggered from Friday 18:00 to Saturday 06:00 Select event trigger.
- Page 70 Administrating the Device Example 3 Enable Voice Alert every 10-minute during 18:00 to 24:00 from Monday to Friday. Type: Select schedule trigger and interval is 10-minute. Enable time: Select Monday to Friday, and set start time from 18:00 and keep work in 6 hours.
-
Page 71: Record
Honeywell Record User can choose the type of record file for event or schedule application. Record File Type Choose a profile to record. Record File Prefix Define the prefix of recorded filename. Pre-Trigger Duration Define the maximum duration of pre-alarm. - Page 72 Administrating the Device Input Status Show either inactive or active. Output Status Show either inactive or active.
-
Page 73: Appendix A: Alarm I/O Connector
Honeywell 9. Appendix A: Alarm I/O Connector Some features of the Camera can be activated by the external sensor that senses physical changes in the area Camera is monitoring. These changes can include intrusion detection or certain physical change in the monitored area. For examples, the external sensor can be a door switch or an infrared motion detector. - Page 74 Appendix A: Alarm I/O Connector CAUTION! THE LOW VOLTAGE/CURRENT CIRCUITS AND HIGH VOLTAGE/ CURRENT • CIRCUITS ARE IN THE NETWORK CAMERA CIRCUIT. THE QUALIFIED ELECTRICIAN SHOULD DO THE WIRING NOT BY YOURSELF. INCORRECT WIRING COULD DAMAGE NETWORK CAMERA AND YOU MIGHT RECEIVE THE FATAL ELECTRIC SHOCK.
-
Page 75: Appendix B: Troubleshooting & Frequently Asked Questions
Honeywell 10. Appendix B: Troubleshooting & Frequently Asked Questions Question Answer or Resolution Features The device utilizes H.264, MPEG4 and MJPEG triple compression to providing The video and audio codec is high quality images. Where H.264 and MPEG4 are standards for video compression and JPEG is a standard for image compression. - Page 76 Appendix B: Troubleshooting & Frequently Asked Questions Make sure that your Internet Explorer is version 8.0 or later. If you are Internet Explorer does not seem experiencing problems, try upgrading to the latest version of Microsoft’s to work well with the device Internet Explorer from the Microsoft webpage.
- Page 77 Honeywell entry for the file “IPCamera Control”. The status column should show installed on your computer “Installed”. If the file is not listed, make sure your Security Settings in Internet Explorer are configured properly and then try reloading the device’s home page.
- Page 78 Appendix B: Troubleshooting & Frequently Asked Questions Miscellaneous Have installed Microsoft®’s DirectX 9.0 or later and use the Windows Media Cannot play the recorded AVI file Player 11.0 or later to play the AVI files recorded by the Device. In addition media player, VLC is another option to play AVI file.
-
Page 79: Appendix C: Ping Ip Address
Honeywell 11. Appendix C: PING IP Address The PING (stands for Packet Internet Groper) command is used to detect whether a specific IP address is accessible by sending a packet to the specific address and waiting for a reply. It’s also a very useful tool to confirm the device installed or if the IP address conflicts with any other devices over the network. -
Page 80: Appendix D: Bandwidth Estimation
The required bandwidth depends on content of video source. The slow motion video will produce smaller bit rate generally and fast motion will produce higher bit rate vice versa. Actual results generated by the device may be varying. Bandwidth Estimation for 720P Camera Image Rate Control Average bit rate for H.264... -
Page 81: Appendix E: Specifications
Honeywell 13. Appendix E: Specifications Camera 720P IR Bullet Network Camera Image Device Sony Exmor image sensor Effective Pixels 1280 x 720 pixels Lens Vari-focal lens: f 3.3-12mm with auto Iris and ICR IP Module Video Video Encoder H.264, MPEG4 and Motion JPEG simultaneously (Tri-encoders) - Page 82 Appendix E: Specifications Notification via email, HTTP, and TCP External output activation Audio alerting output Video Buffer Pre- and post- alarm buffering General 256MB 16MB Power Supply 12V DC external power adapter IEEE 802.3af, class 3 Power Consumption 10W (12VDC) RJ-45 for Gigabit Ethernet DC/AC power jack 1 alarm input and 1 output...
- Page 83 Honeywell IPv4, IPv6, TCP, UDP, HTTP, HTTPS, SMTP, FTP, NTP, DNS, DDNS, DHCP, Supported Protocols DIPS, ARP, Bonjour, UPnP, RTSP, RTP, RTCP, IGMP, PPPoE, Samba, ICMP, SNMP Password protection, IP address filtering, HTTPS encrypted data transmission, user Security access log...
-
Page 84: Appendix F: Configure Port Forwarding Manually
Appendix F: Configure Port Forwarding Manually 14. Appendix F: Configure Port Forwarding Manually The device can be used with a router. If the device wants to be accessed from the WAN, its IP address needs to be setup as fixed IP address, also the port forwarding or Virtual Server function of router needs to be setup. - Page 85 Honeywell Your WAN IP Address will be listed here. Note: Because a dynamic WAN IP can change from time to time depending on your ISP, you may want to obtain a Static IP address from your ISP. A Static IP address is a fixed IP address that will not change over time and will be more convenient for you to use to access your camera from a remote location.
- Page 86 Appendix F: Configure Port Forwarding Manually Important: Some ISPs block access to port 80. Be sure to check with your ISP so that you can open the appropriate ports accordingly. If your ISP does not pass traffic on port 80, you will need to change the port the camera uses from 80 to something else, such as 8080.
-
Page 87: Appendix G: Power Line Frequency
Honeywell 15. Appendix G: Power Line Frequency COUNTRY VOLTAGE FREQUENCY COMMENTS Argentina 220V 50 Hz *Neutral and line wires are reversed from that used in Australia and elsewhere. Australia 230V* 50 Hz *Outlets typically controlled by adjacent switch. Though nominal voltage has been officially changed to 230V, 240V is within tolerances and commonly found. - Page 88 Email: security.ea@honeywell.com https://www.asia.security.honeywell.com India office Honeywell Security Unitech Trade Center, 5th Floor, Sector 43, Block Taiwan office C, Sushant Lok Phase - 1, Gurgaon - 122 002 10F, 168 Lien Cheng Road, Chung Ho City, Taipei, Taiwan R.O.C. Tel: (91) 124 4975000...