hit counter script
LG KG210 Service Manual
  1. Manuals
  2. Brands
  3. LG Manuals
  4. Cell Phone
  5. KG210
  6. Service manual
LG KG210 Service Manual

LG KG210 Service Manual

Hide thumbs Also See for KG210:
Table of Contents

Advertisement

Quick Links

Download this manual
Service Manual
KG210
Date: April, 2006 / Issue 1.0

Advertisement

Table of Contents
loading

Related Manuals for LG KG210

Summary of Contents for LG KG210

  • Page 1 Service Manual KG210 Date: April, 2006 / Issue 1.0...

  • Page 2: Table Of Contents

    Table Of Contents 1. INTRODUCTION .......5 6. BLOCK DIAGRAM ......81 1.1 Purpose ..........5 7. Circuit Diagram ......83 1.2 Regulatory Information......5 1.3 Abbreviations .......... 7 8. pcb layout ........89 2. PERFORMANCE.......9 9. ENGINEERING MODE ....91 2.1 H/W Features...........9 9.1 BB Test [MENU 1]........92 2.2 Technical Specification ......10 9.2 RF Test [MENU 2]........94 3.
  • Page 3 - 4 -...

  • Page 4: Introduction

    1. INTRODUCTION 1. INTRODUCTION 1.1 Purpose This manual provides the information necessary to repair, calibration, description and download the features of this model. 1.2 Regulatory Information A. Security Toll fraud, the unauthorized use of telecommunications system by an unauthorized part (for example, persons other than your company’s employees, agents, subcontractors, or person working on your company’s behalf) can result in substantial additional charges for your telecommunications services.
  • Page 5 1. INTRODUCTION E. Notice of Radiated Emissions This model complies with rules regarding radiation and radio frequency emission as defined by local regulatory agencies. In accordance with these agencies, you may be required to provide information such as the following to the end user. F.

  • Page 6: Abbreviations

    1. INTRODUCTION 1.3 Abbreviations For the purposes of this manual, following abbreviations apply: Automatic Power Control Baseband Bit Error Ratio CC-CV Constant Current - Constant Voltage Digital to Analog Converter Digital Communication System dB relative to 1 milli watt Digital Signal Processing EEPROM Electrical Erasable Programmable Read-Only Memory Electrostatic Discharge...
  • Page 7 1. INTRODUCTION Power Amplifier Module Printed Circuit Board Programmable Gain Amplifier Phase Locked Loop PSTN Public Switched Telephone Network Radio Frequency Receiving Loudness Rating Root Mean Square Real Time Clock Surface Acoustic Wave Subscriber Identity Module Sending Loudness Rating SRAM Static Random Access Memory PSRAM Pseudo SRAM...

  • Page 8: Performance

    2. PERFORMANCE 2. PERFORMANCE 2.1 H/W Features Item Feature Comment Standard Battery Li-ion, 830mAh Stand by TIME Up to 200 hrs : Paging Period 9, RSSI 85dBm Talk time Up to 200min : GSM Tx Level 7 Stand by time Up to 200 hours (Paging Period: 9, RSSI: -85 dBm) Charging time Approx.

  • Page 9: Technical Specification

    2. PERFORMANCE 2.2 Technical Specification Item Description Specification TX: 890 + n x 0.2 MHz RX: 935 + n x 0.2 MHz (n=1~124) EGSM Frequency Band TX: 890 + (n-1024) x 0.2 MHz RX: 935 + (n-1024) x 0.2 MHz (n=975~1024) TX: 1710 + (n-512) x 0.2 MHz RX: 1805 + (n-512) x 0.2 MHz (n=512~885) RMS <...
  • Page 10 2. PERFORMANCE Item Description Specification GSM, EGSM Offset from Carrier (kHz). Max. dBc +0.5 600~ <1,200 1,200~ <1,800 1,800~ <3,000 3,000~ <6,000 Output RF Spectrum 6,000 (due to modulation) Offset from Carrier (kHz). Max. dBc +0.5 600~ <1,200 1,200~ <1,800 1,800~ <3,000 3,000~ <6,000 6,000...
  • Page 11 2. PERFORMANCE Item Description Specification Offset from Carrier (kHz). Max. (dBm) Output RF Spectrum (due to switching transient) 1,200 1,800 Spurious Emissions Conduction, Emission Status GSM, EGSM BER (Class II) < 2.439% @-102 dBm Bit Error Ratio BER (Class II) < 2.439% @-100 dBm RX Level Report Accuracy 3 dB 8 3 dB...
  • Page 12 2. PERFORMANCE Item Description Specification STMR 13 5 dB Stability Margin > 6 dB dB to ARL (dB) Level Ratio (dB) 17.5 22.5 30.7 Distortion 33.3 33.7 31.7 25.5 Side Tone Distortion Three stage distortion < 10% System frequency 2.5ppm (13 MHz) tolerance 32.768KHz tolerance 30ppm...
  • Page 13 2. PERFORMANCE Item Description Specification Forced shut down Voltage 3.33 0.03 V 1 Li-ion Battery Standard Voltage = 3.7 V Battery Type Battery full charge voltage = 4.2 V Capacity: 830mAh Switching-mode charger Travel Charger Input: 100 ~ 240 V, 50/60 Hz Output: 5.2 V, 800 mA - 14 -...

  • Page 14: Technical Brief

    3. TECHNICAL BRIEF 3. TECHNICAL BRIEF 3.1 Power Transceiver (SKY77328, U500) The SKY77328 Power Amplifier Module (PAM) is designed in a low profile (1.2 mm), compact form factor for quad-band cellular handsets comprising GSM850/900, DCS1800, and PCS1900 operation. The PAM also supports Class 12 General Packet Radio Service (GPRS) multi-slot operation. The module consists of separate GSM850/900 PA and DCS1800/PCS1900 PA blocks, impedancematching circuitry for 50 Ω...
  • Page 15 3. TECHNICAL BRIEF SKY77328 PAM Pin Configuration-20-Pin Figure 6. Typical Case Makings Leadless (Top View) Table 4. SKY77328 Pin Names and Signal Descriptions Mame Description Band Select VCC1A VCC (to GSM 1st stage, DCS/PCS 1st stages, BiCMOS PAC) DCS/PCS IN RF input 1710-1910 MHz (DCS1800, PCS1900) GND IN RF input 824-915 MHz (GSM850/900)

  • Page 16: Fem For Triband

    3. TECHNICAL BRIEF 3.2 FEM for Triband Select Mode Vc(EGSM) Vc(DCS/PCS) EGSM-Rx EGSM-Tx High DCS-Rx PCS-Rx DCS/PCS High Table 3-1 Band SW Logic Table GND13 PCS_RX2 GND12 PCS_RX1 GND11 DCS_RX2 GND10 DCS_RX1 GND9 EGSM_RX2 GND8 EGSM_RX1 GND7 GND6 GND5 GND4 GND3 DCSPCS_TX GND2...

  • Page 17: 26 Mhz Clock

    3. TECHNICAL BRIEF 3.3 26 MHz Clock (VCTCXO, X500) The 26 MHz clock(X500) consists of a TCXO(Temperature Compensated Crystal Oscillator) which oscillates at a frequency of 26 MHz. It is used within the SKY77328, base band processor(AD6720,U101), Midi(U203, YMU762C-QZ). 2V75_VVCXO X500 R521 VCONT...

  • Page 18: Baseband Processor

    3. TECHNICAL BRIEF 3.4 Baseband Processor (AD6720 , U101) • AD6720 is an ADI designed processor • AD6720 consists of 1. Control Processor Subsystem including: • 32-bit MCU ARM7TDMI® Control Processor • 39 MHz operation at 1.8V • 1Mb of on-chip System SRAM Memory 2.DSP Subsystem including: •...
  • Page 19 3. TECHNICAL BRIEF Figure 3-4 SYSTEM INTERCONECTION OF AD6720 EXTERNAL INTERFACE - 20 -...
  • Page 20 3. TECHNICAL BRIEF 3.4.1 Interconnection with external devices A. RTC block interface Countered by external X-TAL The X-TAL oscillates 32.768KHz The backlight of LCD module is controlled by AD6720 via AAT3157 , U404. The control signals related to Backlight LED are given bellow. Signals Description MLED...
  • Page 21 3. TECHNICAL BRIEF C. RF interface The AD6720 control RF parts through PA_BAND, ANT_SW1, ANT_SW2, ANT_SW3 , CLKON , PA_EN, S_EN, S_DATA, S_CLK, RF_PWR_DWN. Signals Description PA_BAND (GPO 17) PAM Band Select ANT_SW1 (GPO 9) Antenna switch Band Select ANT_SW2 (GPO 11) Antenna switch Band Select RF_PWR_DWN(GPO 4) Power down Input CLKON...
  • Page 22 3. TECHNICAL BRIEF D. SIM interface The AD6720 provides SIM Interface Module. The AD6720 checks status periodically during established call mode whether SIM card is inserted or not, but it doesn't check during deep Sleep mode. In order to communicate with SIM card, 3 signals SIM_DATA, SIM_CLK, SIM_RST(GPIO_23) are required.

  • Page 23: Battery Charging Block

    3. TECHNICAL BRIEF E. LDO Block There are 8 LDOs in the AD6720. - VCORE : supplies Digital baseband Processor core and AD6720 digital core - VMEM : supplies external memory and the interface to the external memory on the digital baseband processor (1,8V or 2.8V, 150mA) - VEXT : supplies Radio digital interface and high voltage interface (2.8V, 170mA) - VSIM : supplies the SIM interface circuitry on the digital processor and SIM card...
  • Page 24 3. TECHNICAL BRIEF VCHARGE VBAT CHARGING C127 R118 0.1u R119 Q101 R121 R632 PRE_CHARGE_R INDLED_R 1.5K 7.5K R633 R122 UMX1NTN NORMAL CHARGING LIGHT3 1V8_VRTC KEY_BACKLIGHT GPO_22 GPO_23 VBAT VCHARGE VMEMSEL C137 R127 C131 0.1u REFOUT 2.2K C136 TEMP1 C138 TEMP2 D101 R138 C139...

  • Page 25: Display And Interface

    3. TECHNICAL BRIEF 3.6 Display and Interface • Main LCD Properties Spec. Unit Active Screen Size 35.78*40.05*2.8 Color Depth 65,536 colors Resolution 128 X RGB X 128 dots Controlled by LCD_CS, LCD_RESET, LCD_RS, LCD_WR, LCD_RD, IFMODE, L_DATA[00:15] ports • LCD_CS : MAIN LCD driver chip enable. MAIN LCD driver IC has own CS pin •...
  • Page 26 3. TECHNICAL BRIEF - 27 -...

  • Page 27: Keypad Switches And Scanning

    3. TECHNICAL BRIEF 3.7 Keypad Switches and Scanning The key switches are metal domes, which make contact between two concentric pads on the keypad layer of the PCB when pressed. There are 26 switches (Normal Key 24EA, Volume up down side key), connected in a matrix of 5 rows by 5 columns and additional GPIO 35 for KEY_ROW5, as shown in Figure 3-11, except for the power switch (KB1), which is connected independently.

  • Page 28: Microphone

    3. TECHNICAL BRIEF 3.8 Microphone The microphone is placed to the front cover and contacted to main PCB. The audio signal is passed to AIN1P and AININ pins of AD6720. The voltage supply VMIC is output from AD6720, and is a biased voltage for the AIN1P.

  • Page 29: Main Speaker

    3. TECHNICAL BRIEF 3.9 Main Speaker The main speaker is driven directly by AD6720 AOUT1P and AOUT1N pins and the gain is controlled by the PGA in an AD6720. The receiver is placed in the folder cover and connected to AOUT1x terminal via FPCB.

  • Page 30: Headset Interface

    3. TECHNICAL BRIEF 3.10 Headset Interface This phone has 6 electrodes such as GND, AUXIP, AUXIN (this pin is floating), AUXOP, JACK_DETECT, HOOK_DETECT. This type supports mono sound Switching from Receiver to Headset Jack If jack is inserted, JACK_DETECT goes from low to high. Audio path is switched from receiver to earphone by JACK_DETECT interrupt.

  • Page 31: Key Back-Light Illumination

    3. TECHNICAL BRIEF 3.11 Key Back-light Illumination In key back-light illumination, there are 14 Blue LEDs in Main Board, which are driven by KEY_BACKLIGHT signal from AD6720. VBAT VBAT KEY BACKLIGHT Q300 R359 KEY_BACKLIGHT C322 R360 R361 R362 C323 R363 R364 IMX9T110 Figure 3-15.

  • Page 32: Lcd Back-Light Illumination

    3. TECHNICAL BRIEF 3.12 LCD Back-light Illumination LCD backlight LEDs is controlled by AD6720 via AAT3157, U404. WHITE_LED LDO VBAT U404 C419 C418 AAT3157ITP-T1 C417 FB400 C420 MLED R412 LCD_DIM_CTL EN_SET MLED1 MLED2 C450 R499 C421 100K Figure 3-16. MAIN LCD BACKLIGHT ILLUMINATION - 33 -...

  • Page 33: Vibrator

    3. TECHNICAL BRIEF 3.13 VIBRATOR The vibrator is placed in the folder cover and contacted to LCD MODULE. The vibrator is driven from VIBRATOR (GPIO_0) of AD6720 VIBRATOR VBAT VBAT R103 R101 Q100 R104 R105 VIBRATOR MOTOR R106 7.5K EMZ2 C117 4.7u Figure 3-17.

  • Page 34: Trouble Shooting

    4. TROUBLE SHOOTING 4. TROUBLE SHOOTING 4.1 RF Component TEST POINT FL500 SW500 U500 U501 X500 U503 Figure 4-1 U500 Power Amp Module (SKY77328) U501 RF Main Chip (SI4210) U503 2.85V Regulator X500 VCTCXO, 26MHz Clock FL500 SW500 Mobile Switch - 35 -...

  • Page 35: Rx Trouble

    4. TROUBLE SHOOTING 4.2 RX Trouble Checking Flow START HP8960 : Test mode 62 CH, 7 level setting (TCH) 62CH, -60dBm setting (BCCH) Spectrum analyzer setting Oscilloscope setting (1) Check regulator circuit (2) Check VCTCXO (3) Check Mobile SW &FEM (4) Check RX IQ Redownload SW or...
  • Page 36 4. TROUBLE SHOOTING (1) Checking Regulator Circuit TEST POINT U503. 5 (OUT) U503 U503. 3 (EN) CIRCUIT VBAT RF2V85 U503 R522 CLKON MIC5255-2.85BM5 R523 C545 C546 C547 100K 0.01u 4.7u Checking Flow Voltage at Level at Change main board Pin5 of U503 Pin3 of U503 Is 2.85V? Is high?
  • Page 37 4. TROUBLE SHOOTING (2) Checking FEM & Mobile SW TEST POINT Checking Flow X500.4 (VCC) VCTCXO Circuit is OK VCTCXO Circuit is OK 26 MHzO.K? See next Page to check See next Page to check Check Pin 3. Mobile SW Mobile SW Refer to Graph 4 -1(b) 2.75V OK?
  • Page 38 4. TROUBLE SHOOTING (3) Checking Mobile SW & FEM TEST POINT SW500.ANT C541 SW500 C540 SW500.RF VC_DCSPCS(VC1) FL500 VC_EGSM(VC2) FL500.10 (C533) FL500.12 (C533) CIRCUIT Waveform TP500 TP501 TP502 FL301. 10 R502 VC_DCSPCS 5.6nH R503 C588 VC_EGSM 0.5p R588 2.2nH SW500 KMS-506 ANT SW Control GSM&...
  • Page 39 4. TROUBLE SHOOTING Checking Flow For these 2 test case, No Call connection is needed Check SW500 Pin ANT,RF Open Changing SW500 with RF Cable connected. Check SW500 Pin ANT,RF Short Changing SW500 with No RF Cable Connected Check C540,C541 VC1 :Low Changing the Board.
  • Page 40 4. TROUBLE SHOOTING (4) Checking RX IQ TEST POINT CIRCUIT C523 U501 R514 XOUT 26M_DBB C526 C523 C526 Figure 5 Waveform Graph 3 Checking Flow Check C523,C526. Check if there is any Replace U501 Similar? Major difference Refer to graph 4-3 Redownload software and calibration again - 41 -...

  • Page 41: Tx Trouble

    4. TROUBLE SHOOTING 4.3 TX Trouble Checking Flow START HP8960 : Test mode 62 CH, 7 level setting (TCH) 62CH, -60dBm setting (BCCH) Spectrum analyzer setting Oscilloscope setting (1)Check regulator circuit (2)Check VCTCXO (3)Check Mobile SW & FEM (4)Check PAM control signal (5)Check TX IQ...
  • Page 42 4. TROUBLE SHOOTING (1) Checking Regulator Circuit TEST POINT U503. 5 U503 (OUT) U503. 3 (EN) Figure 6 CIRCUIT VBAT RF2V85 U503 R522 CLKON MIC5255-2.85BM5 R523 C545 C546 C547 100K 0.01u 4.7u Checking Flow Voltage at Level at Change main board Pin5 of U503 Pin3 of U503 Is 2.85V?
  • Page 43 4. TROUBLE SHOOTING (2) Checking VCTCXO Circuit TEST POINT Checking Flow X500.4 VCTCXO Circuit is OK VCTCXO Circuit is OK (VCC) 26 MHzO.K? Check Pin 3. See next Page to check See next Page to check Refer to Graph 4(b) Mobile SW Mobile SW X500...
  • Page 44 4. TROUBLE SHOOTING (3) Checking Mobile SW & FEM TEST POINT SW500.ANT SW500 SW500.RF VC_DCSPCS FL500 VC_EGSM Figure 8 CIRCUIT Waveform TP500 TP501 TP502 R502 5.6nH R503 C588 0.5p R588 2.2nH SW500 KMS-506 Graph 5(a) GSM Tx mode C515 GND13 PCS_RX2 GND12 PCS_RX1...
  • Page 45 4. TROUBLE SHOOTING Checking Flow For the test, TX Stand alone Mode is needed. Refer to chapter 11 (PL=7 for GSM, PL=2 for DCS) Check C540,C541 Check whether Ant SW Check VC_EGSM, Changing board Set as TX mode VC_DCSPCS Refer to Graph 5 Refer to Table 4-3 Check RF Level of Pin9 : ~29.5dBm...
  • Page 46 4. TROUBLE SHOOTING (4) Checking PAM Control Signal TEST POINT CIRCUIT VBAT R500 PA_BAND R501 PA_EN C500 C505 C506 U500 U500 ENABLE GSM_IN SKY77328 R506 R503 DCS_PCS_IN (TX_RAMP) R508 R502 (PAM_EN) C519 C520 0.01u 0.01u R513 Figure 9 TX_RAMP C522 Waveform Graph 6 Checking Flow...
  • Page 47 4. TROUBLE SHOOTING (5) Checking TX IQ TEST POINT Waveform U501 C523 C526 Graph 7 Figure 10 CIRCUIT C523 R514 XOUT 26M_DBB C526 Checking Flow Check if there is Similar? Replace U101 Any Major Difference Refer to Graph7 Redownload the Software And calibrate - 48 -...

  • Page 48: Power On Trouble

    4. TROUBLE SHOOTING 4.4 Power On Trouble TEST POINT C112 C114 (2V75_VABB) (2V5_VMIC) C115 (2V75_VVCXO) C111 (2V8_VMEM) C110 U101 (2V8_VEXT) C113 (1V8_VCORE) C116 (2V85_VSIM) Figure 11 CIRCUIT 2V8_VMEM 1V8_VCORE 2V75_VVCXO 2V8_VEXT 2V75_VABB 2V5_VMIC 2V85_VSIM C110 VEXT01 C111 VMEM C112 VABB C113 VCORE C114...
  • Page 49 4. TROUBLE SHOOTING Checking Flow START Check Battery Voltage Charge or Change Battery > 3.35V Push power-on key Check the contact of power key And check the level change Or dome-switch of PWRKEY Check the voltage of Replace U101 The LDO outputs at U101 VCORE=1.8V VVCXO=2.75V VMEM=2.8V...

  • Page 50: Charging Trouble

    4. TROUBLE SHOOTING 4.5 Charging Trouble TEST POINT R129 Q102 R131 D101 Figure 12 CIRCUIT LIGHT3 1V8_VRTC KEY_BACKLIGHT GPO_22 GPO_23 VBAT VCHARGE VMEMSEL C137 R127 C131 0.1u REFOUT 2.2K C136 TEMP1 TEMP2 C138 D101 R138 C139 C140 HOOK_DET AUXADC1 4.7u R129 4.7u AUXADC2...
  • Page 51 4. TROUBLE SHOOTING Checking Flow START Resolder the CN300 I/O Connector(CN300) Pin 4,5 : VCHARGE Is well-soldered ? Pin12,19 : GND The TA is out of order Voltage at anode of Change the TA D101 = 5.2V ? Resolder the Q102,D101,R129 are Q102, D101, R129 well-soldered?

  • Page 52: Vibrator Trouble

    4. TROUBLE SHOOTING 4.6 Vibrator Trouble TEST POINT Q100.6 Q100.1 R103 Q100 R106 R105 Q300.3 R101 (Q100.2) Soldering C heck in LC D Module Figure 13 CIRCUIT VIBRATOR VBAT VBAT R103 R101 Q100 R104 R105 VIBRATOR MOTOR R106 7.5K EMZ2 C117 4.7u - 53 -...
  • Page 53 4. TROUBLE SHOOTING Checking Flow SETTING : Enter the engineering mode, and set vibrator on at vibration of BB test menu START Is the voltage at pin 3 Check the soldering of R105, R106 of Q100 high ? Resolder R105, R106 Check the soldering Is the voltage at pin 2 of R101...

  • Page 54: Lcd Trouble

    4. TROUBLE SHOOTING 4.7 LCD Trouble TEST POINT FL602 FL600 FL604 CN600 FL603 FL601 Figure 14 LCD Module LCD Module connection connector( 60Pin, male ) Figure 15 - 55 -...
  • Page 55 4. TROUBLE SHOOTING Checking Flow START Is the connection of FPCB with connector on Reassemble FPCB with CN600 connector PCB(CN600) ok ? Check the connection LCD Reassemble LCD module with connector on FPCB module with connector On FPCB ? Check the soldering of Resoldering CN600 CN600 ? Change the FPCB and try again...

  • Page 56: Speaker Trouble

    4. TROUBLE SHOOTING 4.8 Speaker Trouble TEST POINT U203 U203.17 Soldering Check U203.18 Figure 18 CIRCUIT DIAGRAM C213 U203 0.1u R211 YMU762C-QZ 26M_MIDI R210 13MHz CLK1 HPOUT_R _MIDI_RESET _RST HPOUT_L ADD00 R212 C214 0.01u _MIDI_CS C218 R214 _MIDI_IRQ _IRQ 120K 270p DATA08 DATA09...
  • Page 57 4. TROUBLE SHOOTING Checking Flow START Check the signal level Re-Place U204 ofU204.17 = 2.85V? Check the state of Replace speaker contact of dual mode speaker Speaker Working well!! - 58 -...

  • Page 58: Sim Card Interface Trouble

    4. TROUBLE SHOOTING 4.9 SIM Card Interface Trouble TEST POINT J100 J100.1 (C128) Figure 19 CIRCUIT DIAGRAM 2V85_VSIM 2V85_VSIM SIM CONNECTOR R120 J100 GND1 SIM_RST R126 SIM_DATA SIM_CLK GND5 GND2 GND4 GND3 C128 C134 C135 C133 1000p 220n - 59 -...
  • Page 59 4. TROUBLE SHOOTING Checking Flow START Change the SIM Card. Our phone Does the SIM cards supports only 3V SIM card. supports 3V ? Voltage output Voltage at pin1 of Resolder J100 of VSIM LDO J100 is 2.85V? Is 2.85V? Replace J100 Change the SIM Card Redownload SW.

  • Page 60: Earphone Trouble

    4. TROUBLE SHOOTING 4.10 Earphone Trouble TEST POINT R206 C208 J200 U201 Figure 20 CIRCUIT DIAGRAM 2V5_JACK CLOSE TO EARJACK 2V8_VEXT 2V5_JACK R200 U202 C201 R201 R202 R203 HOOK_DET AUXIN 1.5K 0.1u VOUT C202 R204 C206 C203 C216 C217 NCP563Q25T1 2V8_VEXT 2V8_VEXT J200...
  • Page 61 4. TROUBLE SHOOTING Checking Flow START Resolder J200 Does the audio Level at pin1 profile of the phone Replace U201 of U201 is high change to the earphone mode? Resolder component Set the audio part of the test equipment to Download software Set the audio part of the test Change the earphone...

  • Page 62: Key Backlight Trouble

    4. TROUBLE SHOOTING 4.11 KEY backlight Trouble TEST POINT R359 Q300 Figure 21 - 63 -...
  • Page 63 4. TROUBLE SHOOTING CIRCUIT VBAT VBAT KEY BACKLIGHT Q300 R359 KEY_BACKLIGHT C322 R360 R361 R362 C323 R363 R364 IMX9T110 Checking Flow START Is the level at R359 Check U101 High? Are all LEDs Check the soldering Working? each R and LED Replace or resoldering Backlight will work properly.

  • Page 64: Receiver Trouble

    4. TROUBLE SHOOTING 4.12 Receiver Trouble TEST POINT R133 R135 U101 Figure 22 CIRCUIT DIAGRAM AIN2P R133 AIN3P REC_P AIN3N C147 AOUT1P R135 AOUT1N REC_N AOUT2P2 R136 AOUT2P1 AOUT2N1 C150 C151 AOUT2N2 AOUT3P AUXOP AOUT3N TDO_ABB TDI_ABB TCK_ABB C153 C154 C152 - 65 -...
  • Page 65 4. TROUBLE SHOOTING Checking Flow SETTING : After initialize Agilent 8960, Test EGSM, DCS mode Set the property of audio as PRBS or continuous wave. Set the receiving volume of mobile as Max. START Does waveform at Replace main board R133 and R135 fluctuate? Is CN600 connected...

  • Page 66: Microphone Trouble

    4. TROUBLE SHOOTING 4.13 Microphone Trouble TEST POINT C220 R208 R219 C223 R217 Figure 23 CIRCUIT DIAGRAM 2V5_VMIC CLOSE TO MIC R213 C219 C215 R215 2.2K R216 R217 VINNORP MIC200 C221 C220 OB4-15L42-C33L C223 R219 VINNORN 0.1u R220 C225 C226 2.2K - 67 -...
  • Page 67 4. TROUBLE SHOOTING Checking Flow SETTING : After initialize Agilent 8960, Test EGSM, DCS mode START Voltage VMIC of U101 Replace U101 = DC 2.5V? Check the signal Level at each side Replace microphone of MIC200. Is it a few tens mV AC? Check the soldering of Resolder component...

  • Page 68: Rtc Trouble

    4. TROUBLE SHOOTING 4.14 RTC Trouble TEST POINT R113 U101 Figure 24 CIRCUIT DIAGRAM KEY_ROW0 KEYPADROW0 KEY_ROW1 KEYPADROW1 KEY_ROW2 KEYPADROW2 C118 KEY_ROW3 KEYPADROW3 X100 KEY_ROW4 KEYPADROW4 OSCIN R113 OSCOUT 26M_DBB CLKIN C124 1000p R153 C125 MC-146 32.768KHz - 69 -...
  • Page 69 4. TROUBLE SHOOTING Checking Flow START Is the voltage level at R113 Check the soldering of R113. about 1.2V Replace X100and try again. RTC will work properly - 70 -...

  • Page 70: Indication Led Trouble

    4. TROUBLE SHOOTING 4.15 Indication LED Trouble TEST POINT R403 C403 R404 LD400 Q400 Q101 Figure 25 CIRCUIT DIAGRAM VBAT R404 R403 C403 VCHARGE VBAT LD400 SML-521MUWT86 C127 R118 0.1u GREEN R119 Q101 R121 R632 R431 PRE_CHARGE_R INDLED_R INDLED_R INDLED_G 1.5K 7.5K R633...
  • Page 71 4. TROUBLE SHOOTING Checking Flow Indication LED only operates in trickle charging mode. START VBAT is 3.6~4. Check the soldering of VBAT(R048/R406) Check the soldering of Is LED working? Q400, Q101,LD400, LED will work properly - 72 -...

  • Page 72: Folder On/Off Trouble

    4. TROUBLE SHOOTING 4.16 Folder on/off Trouble TEST POINT U400 U400.6 (R400) Figure 26 CIRCUIT DIAGRAM FLIP SWITCH 2V8_VMEM R400 FLIP 100K (GPIO_5) U400 OUTPUT C400 GND2 C401 0.01u PGND GND1 A3212EEH-T - 73 -...
  • Page 73 4. TROUBLE SHOOTING Checking Flow START Is there the magnet Place the magnet properly. in the folder side? Voltage at pin 1 Voltage of VMEM at U101 of U400 = 2.8V? = 2.8V? Resolder U400 Replace U101 Open folder. Resolder R400 and U400 Voltage at pin 1 of U400 =2.8V Close folder.

  • Page 74: Download

    5. DOWNLOAD 5. DOWNLOAD 5.1 Download A. Download Setup Figure 5-1 describes Download setup Figure 5-1. Download Setup - 75 -...
  • Page 75 5. DOWNLOAD B. Multi Download Procedure 1. Run GSM Multi Download program and select Setting KG210 - 76 -...
  • Page 76 5. DOWNLOAD 2. Select Configuration from the menu and you may see this window 3. Press key to select DLL file and press Open - 77 -...
  • Page 77 5. DOWNLOAD 4. Press key to select the mot files 5. Select AlchemyData.mot and press open 6. Repeat step 4-5 to select CodeData.mot - 78 -...
  • Page 78 5. DOWNLOAD 7. Check if the ADI option is set to Hermes 8. Press OK to end Configuration Select Rate - 79 -...
  • Page 79 5. DOWNLOAD 9. Press START to execute download 10. Once downloading is started, press STOP button to keep from re-downloading after downloading is completed. Start KG210 Stop - 80 -...

  • Page 80: Block Diagram

    6. BLOCK DIAGRAM 6. BLOCK DIAGRAM - 81 -...
  • Page 81 - 82 -...

  • Page 82: Circuit Diagram

    Date Sign & Name Sheet/ Sheets 02/06 BUTTERFLY(KG210) MODEL Designer 2006 Checked DRAWING MAIN CHIP, Base Band NAME Approved OJ100 OJ101 OJ102 OJ103 DRAWING VER-1.1 LG Electronics Inc. Iss. Notice No. Date Name LG(42)-A-5505-10:01 LG Electronics Inc. - 83 -...
  • Page 83 IOVDD 2.2K C227 0.1u C228 C229 SPVSS Section Sign & Name Date Sheet/Sheets MODEL BUTTERYFLY(KG210) 06/02 Designer 2006 Checked DRAWING AUDIO NAME Approved DRAWING Iss. Notice No. Date Name VER-1.1 LG Electronics Inc. LGIC(42)-A-5505-10:01 LG Electronics Inc. - 84 -...
  • Page 84 Section Date Sign & Name R359 Sheet/Sheets KEY_BACKLIGHT MODEL BUTTERFLY(KG210) 02/06 Designer C322 R360 R361 2006 R362 C323 R363 R364 IMX9T110 Checked DRAWING MMI, I/O Connector NAME Approved DRAWING VER-1.1 LG Electronics Inc. LGIC(42)-A-5505-10:01 LG Electronics Inc. - 85 -...
  • Page 85 R499 C421 100K R414 R417 Section Date Sign & Name Sheet/ Sheets MODEL BUTTERFLY(KG210) Designer Checked DRAWING CAMERA IC/ CHARGE PUMP NAME Approved DRAWING Iss. Notice No. Date Name VER-1.1 LG Electronics Inc. LGIC(42)-A-5505-10:01 LG Electronics Inc. - 86 -...
  • Page 86 100K 0.01u 4.7u Section Date Sign & Name Sheet/Sheets MODEL BUTTERFLY(KG210) 02/06 Designer 5 / 6 2006 Checked RF PART DRAWING NAME Approved DRAWING Iss. Notice No. Date Name VER-1.1 LG Electronics Inc. LGIC(42)-A-5505-10:01 LG Electronics Inc. - 87 -...
  • Page 87 INOUT_B4 Out of PDM Section Date Sign & Name Sheet/ MODEL Sheets BUTTERFLY(KG210) Out of PDM Designer Checked DRAWING LCD CONNECTOR NAME Approved DRAWING VER-1.1 Iss. Notice No. Date Name LG Electronics Inc. LGIC(42)-A-5505-10:01 LG Electronics Inc. - 88 -...

  • Page 88: Pcb Layout

    8. PCB LAYOUT - 89 -...
  • Page 89 8. PCB LAYOUT - 90 -...

  • Page 90: Engineering Mode

    9. ENGINEERING MODE 9. ENGINEERING MODE A. About Engineering Mode Engineering mode is designed to allow a service man/engineer to view and test the basic functions provided by a handset. B. Access Codes The key sequence for switching the engineering mode on is 2945#*#. Pressing END will switch back to non-engineering mode operation.

  • Page 91: Bb Test [Menu 1]

    9. ENGINEERING MODE 9.1 BB Test [MENU 1] 9.1.1 LED This menu is to test the LED. 1) Green On 2) Green Off 3) Red On 4) Red Off 9.1.2 LCD 1) COLOUR : WHITE, RED, GREEN, BLUE, BLACK 2) Contrast Value 9.1.3 Backlight This menu is to test the LCD Backlight and Keypad EL Backlight.
  • Page 92 9. ENGINEERING MODE 9.1.6 ADC (Analog to Digital Converter) This displays the value of each ADC. 1) MVBAT ADC : Main Voltage Battery ADC 2) AUX ADC : Auxiliary ADC 3) TEMPER ADC : Temperature ADC 9.1.7 BATTERY 1) Bat Cal : This displays the value of Battery Calibration. The following menus are displayed in order : BAT_LEV_4V, BAT_LEV_3_LIMIT, BAT_LEV_2_LIMIT, BAT_LEV_1_LIMIT, BAT_IDLE_LI MIT, BAT_INCALL_LIMIT, SHUT_DOWN_VOLTAGE, BAT_RECHARGE_LMT...

  • Page 93: Rf Test [Menu 2]

    9. ENGINEERING MODE 9.2 RF Test [MENU 2] 9.2.1 SAR test This menu is to test the Specific Absorption Rate. 1) SAR test on : Phone continuously process TX only. Call-setup equipment is not required. 2) SAR test off : TX process off 9.3 MF mode [MENU 3] This manufacturing mode is designed to do the baseband test automatically.

  • Page 94: Trace Option [Menu 4]

    9. ENGINEERING MODE 9.3.7 Key pad When a pop-up message shows ‘Press Any Key’, you may press any keys including side keys, but not [Soft2 Key]. If the key is working properly, name of the key is displayed on the screen. Test will be completed in 15 seconds automatically.

  • Page 95: Stand Alone Test

    10. STAND ALONE TEST 10. STAND ALONE TEST 10.1 Introduction This manual explains how to examine the status of RX and TX of the model. A. Tx Test TX test - this is to see if the transmitter of the phones is activating normally. B.

  • Page 96: Means Of Test

    10. STAND ALONE TEST 10.3 Means of Test a. Select a COM port b. Set the values in Tx or Rx c. Select band and channel d. After setting them all above, press connect button. e. Press the start button Figure 10-1.
  • Page 97 10. STAND ALONE TEST Figure 10-2. HW test setting Figure 10-3. Ramping profile - 98 -...

  • Page 98: Auto Calibration

    11. AUTO CALIBRATION 11. AUTO CALIBRATION 11.1 Overview Auto-cal (Auto Calibration) is the PC side Calibration tool that perform Tx, Rx and Battery Calibration with Agilent 8960(GSM call setting instrument) and Tektronix PS2521G(Programmable Power supply). Auto-cal generates calibration data by communicating with phone and measuring equipment then write it into calibration data block of flash memory in GSM phone.

  • Page 99: Test Jig Operation

    11. AUTO CALIBRATION JTAG2 JTAG1 Status ADI-REMOTE TI-REMOTE POWER VBAT UART Status POWER Figure 11-2 The top view of Test JIG 11.3 Test Jig Operation Power Source Description Power Supply Usually 4.0V Table 11-2 Jig Power Switch Number Name Description Switch 1 ADI-REMOTE In ON state, phone is awaked.

  • Page 100: Procedure

    1. Connect as Fig 11-2 (RS232 serial cable is connected between COM port of PC and MON port of TEST JIG, in general.) 2. Run Hot_Kimchi.exe to start calibration. 3. From the Calibration Lib menu, Select F3000, then, Press APPLY! KG210 - 101 -...
  • Page 101 11. AUTO CALIBRATION 4. Press Calibration START KG220 KG220 This model is KG220) Test band : GSM900/DCS 1800/PCS 1900 Max target : dfasdf - 102 -...
  • Page 102 11. AUTO CALIBRATION 5. Select RF Cable Loss value from the Offset menu 6. Press START to execute calibration KG210 - 103 -...

  • Page 103: Agc

    11. AUTO CALIBRATION 11.5 AGC This procedure is for Rx calibration. In this procedure, We can get RSSI correction value. Set band EGSM and press Start button the result window will show correction values per every power level and gain code and the same measure is performed per every frequency.

  • Page 104: Exploded View & Replacement Part List

    12. EXPLODED VIEW & REPLACEMENT PART LIST 12.1 EXPLODED VIEW - 105 -...
  • Page 105 - 106 -...

  • Page 106: Replacement Parts

    KG210 RUS Black MPBJ00 PAD,MOTOR MPBJ0029301 KG220 ORFDB Black MPBN00 PAD,SPEAKER MPBN0027201 KG220 ORFDB Black MPBZ00 MPBZ0121001 KG210 RUS (Pad, Back-Up Battery) Black MTAA00 TAPE,DECO MTAA0113001 KG210 RUS MTAB00 TAPE,PROTECTION MTAB0115501 KG210 CIS ACGK00 COVER ASSY,FRONT ACGK0066701 KG220 ORFDB Silver...
  • Page 107 8.5:1 ,-10 dBd, ,GSM900/DCS1800/DCS1900 Internal SNGF00 ANTENNA,GSM,FIXED SNGF0013701 Pb-free GMEY00 SCREW MACHINE,BIND GMEY0011201 1.4 mm,3 mm,MSWR3(BK) ,N ,+ ,NYLOK 13,50 MBJA00 BUTTON,DIAL MBJA0020202 KG210 RUS MCCF00 CAP,MOBILE SWITCH MCCF0032401 KG220 ORFDB Silver MLAK00 LABEL,MODEL MLAK0019002 KG210 CIS White Pearl SAFY00 PCB ASSY,MAIN...

  • Page 108: Main Component

    12. EXPLODED VIEW & REPLACEMENT PART LIST <Main component> Note: This Chapter is used for reference, Part order is ordered by SBOM standard on GCSC Location Level Description Part Number Specification Color Remark GSM(FOLDER) TGFF0089801 AAAY00 ADDITION AAAY0160201 Black SACY00 PCB ASSY,FLEXIBLE SACY0046101 PCB ASSY,...
  • Page 109 12. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark C112 CAP,CERAMIC,CHIP ECCH0004904 1 uF,6.3V ,K ,X5R ,TC ,1005 ,R/TP C113 CAP,CERAMIC,CHIP ECCH0004904 1 uF,6.3V ,K ,X5R ,TC ,1005 ,R/TP C114 CAP,CERAMIC,CHIP ECCH0004904 1 uF,6.3V ,K ,X5R ,TC ,1005 ,R/TP C115 CAP,CERAMIC,CHIP ECCH0004904...
  • Page 110 12. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark C152 CAP,CERAMIC,CHIP ECCH0000120 39 pF,50V,J,NP0,TC,1005,R/TP C153 CAP,CERAMIC,CHIP ECCH0000120 39 pF,50V,J,NP0,TC,1005,R/TP C154 CAP,CERAMIC,CHIP ECCH0000120 39 pF,50V,J,NP0,TC,1005,R/TP C200 CAP,TANTAL,CHIP,MAKER ECTZ0005201 10 uF,6.3V ,M ,L_ESR ,1608 ,R/TP C201 CAP,CERAMIC,CHIP ECCH0000167 0.1 uF,6.3V,K,X5R,HD,1005,R/TP...
  • Page 111 12. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark C323 CAP,CERAMIC,CHIP ECCH0000117 27 pF,50V,J,NP0,TC,1005,R/TP C402 CAP,CERAMIC,CHIP ECCH0004904 1 uF,6.3V ,K ,X5R ,TC ,1005 ,R/TP C404 CAP,CERAMIC,CHIP ECCH0000143 1 nF,50V,K,X7R,HD,1005,R/TP C405 CAP,CERAMIC,CHIP ECCH0004904 1 uF,6.3V ,K ,X5R ,TC ,1005 ,R/TP C417 CAP,CERAMIC,CHIP ECCH0004904...
  • Page 112 12. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark C534 CAP,CERAMIC,CHIP ECCH0000115 22 pF,50V,J,NP0,TC,1005,R/TP C535 CAP,CERAMIC,CHIP ECCH0000167 0.1 uF,6.3V,K,X5R,HD,1005,R/TP C536 CAP,CHIP,MAKER ECZH0001421 2.2 uF,6.3V ,K ,X5R ,HD ,1608 ,R/TP C537 CAP,CERAMIC,CHIP ECCH0000143 1 nF,50V,K,X7R,HD,1005,R/TP C538 CAP,CERAMIC,CHIP ECCH0000143...
  • Page 113 12. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark Q101 TR,BJT,ARRAY EQBA0000406 SC-70 ,0.2 W,R/TP ,CDMA,Common use 2.9*1.9*0.8(t) ,.7 W,20 V,-6 A,R/TP ,NDC652P Q102 TR,FET,P-CHANNEL EQFP0004201 upgrade(substitution) item, Pb free Q300 TR,BJT,NPN EQBN0004801 SMT6 ,0.2 W,R/TP , Q400 TR,BJT,NPN EQBN0017701...
  • Page 114 12. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark R202 RES,CHIP ERHY0000241 1K ohm,1/16W,J,1005,R/TP R203 RES,CHIP ERHY0000201 0 ohm,1/16W,J,1005,R/TP R205 RES,CHIP ERHY0000296 1M ohm,1/16W,J,1005,R/TP R206 RES,CHIP ERHY0000202 4.7 ohm,1/16W,J,1005,R/TP R207 RES,CHIP ERHY0000202 4.7 ohm,1/16W,J,1005,R/TP R208 RES,CHIP ERHY0000291...
  • Page 115 12. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark R362 RES,CHIP ERHY0000262 12K ohm,1/16W,J,1005,R/TP R363 RES,CHIP ERHY0000203 10 ohm,1/16W,J,1005,R/TP R364 RES,CHIP ERHY0000203 10 ohm,1/16W,J,1005,R/TP R402 RES,CHIP ERHY0000201 0 ohm,1/16W,J,1005,R/TP R412 RES,CHIP ERHY0000265 20K ohm,1/16W,J,1005,R/TP R430 RES,CHIP ERHY0000262...
  • Page 116 12. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark R606 RES,CHIP ERHY0000224 180 ohm,1/16W,J,1005,R/TP R607 RES,CHIP ERHY0000224 180 ohm,1/16W,J,1005,R/TP R608 RES,CHIP ERHY0000224 180 ohm,1/16W,J,1005,R/TP R609 RES,CHIP ERHY0000224 180 ohm,1/16W,J,1005,R/TP R610 RES,CHIP ERHY0000224 180 ohm,1/16W,J,1005,R/TP R611 RES,CHIP ERHY0000224...
  • Page 117 12. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark U502 EUSY0077201 SC70 ,5 PIN,R/TP ,Inverter Gate, Pb Free SOT23 ,5 PIN,R/TP ,2.85V/150mA Low Noise uCap LDO U503 EUSY0118602 Regulator, PBFREE VA200 VARISTOR SEVY0003901 5.5 V, ,SMD ,480pF, 1005 VA201 VARISTOR SEVY0003901...
  • Page 118 12. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark LD301 DIODE,LED,CHIP EDLH0006001 Blue ,1608 ,R/TP ,Blue SMD LED LD302 DIODE,LED,CHIP EDLH0006001 Blue ,1608 ,R/TP ,Blue SMD LED LD303 DIODE,LED,CHIP EDLH0006001 Blue ,1608 ,R/TP ,Blue SMD LED LD304 DIODE,LED,CHIP EDLH0006001...
  • Page 119 12. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark R354 RES,CHIP ERHY0000220 100 ohm,1/16W,J,1005,R/TP R355 RES,CHIP ERHY0000220 100 ohm,1/16W,J,1005,R/TP R356 RES,CHIP ERHY0000220 100 ohm,1/16W,J,1005,R/TP R357 RES,CHIP ERHY0000220 100 ohm,1/16W,J,1005,R/TP R358 RES,CHIP ERHY0000220 100 ohm,1/16W,J,1005,R/TP R400 RES,CHIP ERHY0000280...

  • Page 120: Accessory

    MSFG0000801 Steaker seal of Data kit case MHBY00 HANDSTRAP MHBY0003604 MLAA00 LABEL,APPROVAL MLAA0037301 KG210 CIS White 3.7 V,830 mAh,1 CELL,PRISMATIC ,KG210 OPEN BATT SBPL00 BATTERY PACK,LI-ION SBPL0084101 Black BK, Pb-Free EAR PHONE/EAR MIKE SGEY00 SGEY0003204 L1200 ,MONO TYPE 100-240V ,60 Hz,5.2 V,800 mA,CE,CB,GOST ,EU...
  • Page 121 Note...
  • Page 122 Note...

Table of Contents