Table of Contents
Advertisement
Quick Links
Additional Technical Manual
Introduction
This technical manual applies for the mainboard D1085. This system board is available in different
configuration levels. Depending on the hardware configuration of your device, it may be that you
cannot find several options in your version of the system board, even though they are described.
Further information e. g. the complete Technical Manual for the D1085 and the Reference Manual
for the BIOS Setup are provided on the "Drivers & Utility" CD. For detailed information please
look at chapter 3.
1
Features
Function
Processor
Chipset
AGP connector
Wake on LAN (WOL) connector
USB
IrDA connector
Chipcard reader
Keyboard on
BIOS Fax
Quiet Boot
DMI
Systemmonitoring
DIMM
Memory ECC Support
FAX On
PCI Slots*
ISA Slots*
* = 1 PCI/ISA slot is shared
2
Mechanics
Computer mainboards and components contain very delicate IC chips. To protect
!
them against damage caused from electric static, you have to follow some
precautions:
•
Unplug your computer when you work inside.
•
Hold components by the edge, don't touch their leads.
•
Use a grounded wrist strap.
Place the mainboard and the components on a grounded antistatic pad whenever
you work outside the computer.
Once you have installed the system board, you should remove the battery
protection (i.e. the thin plastic plate between battery and contact spring).
A26361-D1085-Z180-2-7619
Version
D1085-A
Intel Pentium®II,
233 - 333 MHz
Intel Celeron™
Intel 440LX
X
X
X
X
X
X
-
X
X
X
3
X
-
4
3
Version
D1085-E
Intel Pentium®II,
233 - 333 MHz
Intel Celeron™
Intel 440EX
X
-
X
-
-
-
-
X
X
-
2
-
-
4
3
Page 1
Advertisement
Chapters
Table of Contents
Related Manuals for Siemens D1085-A
Summary of Contents for Siemens D1085-A
-
Page 1: Introduction
Further information e. g. the complete Technical Manual for the D1085 and the Reference Manual for the BIOS Setup are provided on the "Drivers & Utility" CD. For detailed information please look at chapter 3. Features Function Version Version D1085-A D1085-E Processor Intel Pentium®II, Intel Pentium®II, 233 - 333 MHz 233 - 333 MHz Intel Celeron™... -
Page 2: Layout
Additional Technical Manual Layout ATX 12’’ x 7,3’’ (305 mm x 185,4 mm) Some of the following connectors are optional and may therefore not be included on your mainboard. 1 = Serial port 2 4 = PS/2 keyboard port 2 = Serial port 1 5 = Parallel port 3 = PS/2 mouse port 6 = USB ports... -
Page 3: Data.
Additional Technical Manual 3 2 1 PCI 4 PCI 3 PCI 2 PCI 1 ISA 3 ISA 2 ISA 1 1 = System fan 8 = IDE drives 1 and 2 (primary) 2 = Chipcard reader 9 = Floppy disk drive 3 = Power supply 10 = Processor fan 4 = Infrared receiver (IrDA) -
Page 4: Assembling Slot 1
Additional Technical Manual Assembling Slot 1 Before inserting the CPU, you have to assembly the including stabilisators. Please be carefully to avoid a damage of the mainboard. Connectors, DIP-Switch, Jumpers Some of the following connectors are optional! 2.3.1 Power supply ATX connector Pin 11 Pin 1 Signal... -
Page 5: Power On Switch Connector
Additional Technical Manual 2.3.3 Power on switch connector Signal Pin 1 Power on pulse (low asserted) 2.3.4 Wake on LAN (WOL) connector (stuffing option) Signal Pin 1 + 5 V SB Wake pulse (high asserted) 2.3.5 CPU-FAN connector Pin 1 Signal FAN power supply FAN sense... -
Page 6: Internal Infrared (Irda) Connector
Additional Technical Manual 2.2.7 Internal infrared (IrDA) connector Signal Pin 1 VCCHELP IRDA_RX IRDA_TX 2.2.8 Internal speaker connector Signal Pin 1 Speaker output 2.3.9 System management SM-BUS Signal Pin 1 SM Clock SM Data Page 6 A26361-D1085-Z180-2-7619... -
Page 7: Front Panel Connector 1
Additional Technical Manual 2.3.10 Front panel connector 1 Pin Signal Signal Pin 1 Pin 2 Boot Lock Speaker (high asserted) Stand By LED (high asserted) Power On LED (high asserted) Speaker Key Pin Power On & Stand By LED (low asserted) Message LED (high asserted) Message LED... -
Page 8: Table Of Contents
Additional Technical Manual 2.3.11 PCI-IDE Connector Signal Signal Reset Drive Data 7 Data 8 Data 6 Data 9 Data 5 Data 10 Data 4 Data 11 Data 3 Data 12 Data 2 Data 13 Data 1 Data 14 Data 0 Data 15 I/O Write I/O Read... -
Page 9: Infrared Connector
Additional Technical Manual 2.3.13 Infrared Connector Signal Pin 1 IRDA_RX IRDA_TX 2.3.14 Front Panel Connector 1 Pin 1 Signal Boot Lock + Standby LED + Power LED - Standby/ Power LED Keylock + HD LED HD LED HD LED A26361-D1085-Z180-2-7619 Page 9... -
Page 10: Configuration Switch-Block (Dip-Switch)
Additional Technical Manual 2.3.15 Configuration SWITCH-Block (DIP-Switch) For Frequency selection, Reserved, Password clear, Recovery and Floppy write. Function Password Skip Recovery BIOS Floppy Write Protect Reserved Reserved Recovering System BIOS - switch 2 Switch 2 enables recovery of the old system BIOS after an attempt to update has failed. To restore the old system BIOS you need a Flash BIOS Diskette (call customer service). -
Page 11: Pci-Slot Configuration And Placement
Additional Technical Manual Clock speed - switch 5, 6, 7 and 8 The switches may only be set as specified in the table below for the particular Pentium II used. This system board you may use with processors with a host bus frequency of 66 MHz only. -
Page 12: Installing Drivers And Utilities; Documentation
Additional Technical Manual Installing drivers and utilities; documentation Insert the "Drivers & Utilities" CD. When the DeskStart window appears, select Explore the CD via HTML. Select the language in which you want to operate the user interface. Select Scenic Pro and then select e. g. Windows 95. Here you will find the required drivers, utilities and the additional documentation. -
Page 13: Data
Additional Technical Manual 32MB DIMM SDRAM, 4Mx72 Producer Part.-No Goldstar GMM2734233BLTG-10K Hyundai HYM7V72A400TFG-10 Samsung KMM374S4030BTN-G2 64MB DIMM SDRAM, 8Mx64 Producer Part.-No MC-458CB644F-A10 Samsung KMM366S823BTL-G0 64MB DIMM SDRAM, 8Mx72 Producer Part.-No MC458CA724F-A10 Samsung KMM374S823BTL-G0 128MB DIMM SDRAM, 16Mx64 Producer Part.-No MC-4516CD644F-A10 128MB DIMM SDRAM, 16Mx72 Producer Part.-No... -
Page 14: Data
Additional Technical Manual Contents Introduction ............................1 1 Features ............................1 2 Mechanics ............................1 2.1 Layout ............................2 2.2 Assembling Slot 1........................4 2.3 Connectors, DIP-Switch, Jumpers ....................4 2.3.1 Power supply ATX connector.................... 4 2.3.2 Power control connector .................... -
Page 15: Data
Additional Technical Manual A26361-D1085-Z180-2-7619 System board D1085 Additional Technical Manual October 1998 edition Copyright © Siemens AG September 1998. A26361-D1085-Z180-2-7619...