Honeywell LYNX TOUCH Quick Manual page 2
Hide thumbs
Also See for LYNX TOUCH:
- User manual (96 pages) ,
- Step-by-step manual (2 pages) ,
- Programming manual (24 pages)
Advertisement
Z-Wave® System Basics (Continued)
Z-Wave Device Management Screen Options
Button
Include Devices
Exclude Devices
View Failed Devices
Advanced Tools
Z-Wave® Advanced Tools
Z-Wave Advanced Tools Options
Button
View Z-Wave device information.
View Enrolled Devices
View Enrolled
View Controller Information.
Controllers
Deletes all nodes and generates a new
Reset Controller
random Home ID. Resetting the Controller
does not Exclude the individual devices.
Transfers the role of primary controller to
Pri. Controller Shift
another controller (i.e.; a Z-Wave remote
control)
to Secondary
network.
Enable Arm Stay, Arm Away or Arm without
Auto-Stay when Z-Wave door lock is locked.
Locking Door
Causes the system to arm in the selected
mode, Away, Stay, or Away without Auto-
Stay when the Z-Wave Door is Locked.
Includes the panel as secondary controller,
Learn
usually on a Z-Wave remote control, and
duplicates the Z-Wave network.
All Devices Off
Allows User to "manually" turn Off OR On all
switches that are programmed in the Z-
OR
Wave Network.
All Devices On
Including Z-Wave® Devices
The steps described below should be accomplished at the LYNX
Touch control in order to include (add) Z-Wave devices to the
network. For additional information regarding the inclusion of
specific Z-Wave Devices refer to the full Home Automation Guide
P/N 800-16091 or higher.
Step
1.
At the Home Screen select the "Automation" icon
2.
At the second page of the Automation Screen, select
"Tools".
3.
At the "Device Management" screen, select "Include
Devices".
The panel displays "Entering Inclusion Mode.
Please Wait..."
4.
"Ready to include device. Press the function button on
device" is displayed. Within one minute press the device's
Function button or activate the switch, as applicable.
5.
If the module has been successfully enrolled, the panel
displays "Device Found! Please Wait" and then displays the
device information.
6.
After
successfully
information will be added to the top of the inclusion list.
7.
Repeat steps 4 - 6 to enroll additional Z-Wave devices.
8.
Once you have finished including devices, press the "Home"
key to return to the Home screen or select the "" button
to return to the previous screen.
Function
Enroll Z-Wave Devices/Modules
Delete Z-Wave Devices/Modules
Displayed only when device failures have
been detected in the Z-Wave network
(For additional information Refer to the
Failed Device section of LYNX Touch
Security System Home Automation Guide
P/N 800-16091 or higher)
Provides access to additional Z-Wave
options.
Function
and
duplicates
Action
including
a
device,
the
Editing Z-Wave Device Names
The steps described below should be accomplished at the LYNX
Touch control in order to edit a Z-Wave devices name.
Step
1.
At the Home Screen select the "Automation" icon.
2.
At the Automation Screen, select the type of device to edit.
3.
Select the device that you wish to edit from the list.
4.
Select the edit button
5.
Enter the desired information (limited to 14 characters) on
the displayed keypad and then select "Done". The system
returns to the previous screen.
6.
Press the "Home" key to return to the Home screen or
select the "" button to return to the Automation screen.
Excluding Z-Wave® Devices
The steps described below should be accomplished at the LYNX
Touch control in order to Exclude
the network.
Step
1.
At the Home Screen select the "Automation" icon.
2.
At the Automation Screen, select "Tools".
3.
At the "Device Management" screen, select "Exclude
Devices".
4.
"Entering Exclusion Mode. Please Wait..." is displayed
followed by "Ready to Exclude device. Press the function
the
Z-Wave
button on the device". Within one minute press the
device's Function button or activate the switch.
5.
If the device has been successfully excluded, the device
information is shown on the excluded list.
which is not known to the panel is excluded, "Unknown
Device Excluded" is displayed on the excluded list.
6.
Once you have finished excluding devices, press the
"Home" key to return to the Home screen or select the
"" button to return to the previous screen.
Controlling Z-Wave Devices
Z-Wave devices can be activated Manually or by using Scenes to
control a single or group of devices, by turning them OFF, ON,
ON to a preset lighting level, temperature or mode, and/or to
lock/unlock a door.
can be configured to control up to 10 devices each. Scenes can
be activated manually or by a Schedule or Rule. Schedules and
Rules are used to control Scenes via pre-set "Conditions" and
"Triggers".
LYNX Touch. An additional 20 Rules can be programmed through
Total Connect Service. Check with your Installer to see if these
features
are available to you.
Manually Activating Z-Wave Devices
The steps described below should be accomplished at the LYNX
Touch control in order to manually activate devices.
Step
1.
At the Home Screen select the "Automation" icon.
2.
At the Automation Screen, select the type of device (i.e.;
Switches, Thermostats or Locks) that you wish to control.
3.
Select the device that you wish to control from the
displayed list.
4.
Refer to the figures below for typical examples of the
features that can be controlled manually for the devices.
associated
5.
Press the "BACK" key to return to the previous screen.
6.
Press the "Home" key to return to the Home screen or
select the "" button to return to the Automation screen.
Note: The features and functions that can be controlled vary by
manufacturer. Refer to the User Manual that was provided with
the Z-Wave device to determine the specific capabilities.
Action
(remove)
Action
The LYNX Touch provides 20 Scenes that
Up to 20 Rules may be programmed locally in the
Action
a Z-Wave device from
If a device,
Advertisement
