Specifications - Makita 6908D Instruction Manual
Hide thumbs
Also See for 6908D:
- Instruction manual (16 pages) ,
- Technical information (4 pages) ,
- Instruction manual (21 pages)
Table of Contents
Advertisement
Available languages
Available languages
ENGLISH
1 Button
2 Battery cartridge
3 Charging light
4 Fast charger
5 Bit
6 Sleeve
7 Switch trigger
8 Reversing switch lever
SPECIFICATIONS
Model
Capacities
Machine screw ......................................... M4 – M8
Standard Bolt ......................................... M5 – M12
High tensile bolt ..................................... M5 – M10
–1
No load speed (min
) ............................... 0 – 2,200
Impacts per minute .................................... 0 – 2,800
Overall length ............................................... 171 mm
Net weight ....................................................... 1.4 kg
Rated voltage ........................................... D.C. 9.6 V
• Due to the continuing program of research and
development, the specifications herein are subject
to change without prior notice.
• Note: Specifications may differ from country to
country.
Safety hints
For your own safety, please refer to enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS
FOR CHARGER & BATTERY
CARTRIDGE
1. SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating
instructions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
3. CAUTION — To reduce risk of injury, charge
only MAKITA type rechargeable batteries.
Other types of batteries may burst causing
personal injury and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or
sold by the battery charger manufacturer may
result in a risk of fire, electric shock, or injury
to persons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when dis-
connecting charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise sub-
jected to damage or stress.
8. Do not operate charger with damaged cord or
plug — replace them immediately.
4
Explanation of general view
9 A side
10 B side
11 Clockwise
12 Counterclockwise
13 Screw
14 Set plate
15 Kg . cm
9. Do not operate charger if it has received a
6908D
10. Do not disassemble charger or battery car-
11. To reduce risk of electric shock, unplug
12. The battery charger is not intended for use by
13. Young children should be supervised to
14. If operating time has become excessively
15. If electrolyte gets into your eyes, rinse them
ENC001-3
ADDITIONAL SAFETY RULES FOR
CHARGER & BATTERY CARTRIDGE
1. Do not charge battery cartridge when tempera-
2. Do not attempt to use a step-up transformer,
3. Do not allow anything to cover or clog the
4. Always cover the battery terminals with the
16 Fastening torque
17 Proper fastening torque for
18 Seconds
19 Fastening time
20 Limit mark
21 Screwdriver
22 Brush holder cap
sharp blow, been dropped, or otherwise dam-
aged in any way; take it to a qualified service-
man.
tridge; take it to a qualified serviceman when
service or repair is required. Incorrect reas-
sembly may result in a risk of electric shock or
fire.
charger from outlet before attempting any
maintenance or cleaning. Turning off controls
will not reduce this risk.
young children or infirm persons without
supervision.
ensure that they do not play with the battery
charger.
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
ture is BELOW 10°C (50°F) or ABOVE 40°C
(104°F).
an engine generator or DC power receptacle.
charger vents.
battery cover when the battery cartridge is not
used.
- Quick Links:
- Specifications
Hide quick links:
Advertisement
Table of Contents
