Page 1 ___________________ SCALANCE W760/W720 to IEEE Introduction 802.11n Command Line Interface ___________________ Description ___________________ SIMATIC NET Configuration Functions specific to ___________________ SCALANCE Industrial Wireless LAN SCALANCE W760/W720 to IEEE ___________________ 802.11n Command Line Interface System time ___________________ Network structures Configuration Manual...
Page 2 Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
Page 3: Table Of Contents
........................41 3.1.1.12 show versions ......................... 41 3.1.2 clear counters ......................... 42 3.1.3 configure terminal ........................43 3.1.4 clear line vty ..........................44 3.1.5 disable ............................. 45 SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 4 3.4.1 show running-config ....................... 75 3.4.2 write startup-config ......................... 77 3.4.3 Commands in the global configuration mode ................ 78 auto-save ..........................78 3.4.3.1 3.4.3.2 no auto-save .......................... 79 SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 6 (access point) ................144 6.1.5.5 wlan ampdu .......................... 145 6.1.5.6 no wlan ampdu ........................146 6.1.5.7 wlan ampdu bytes-limit ......................146 6.1.5.8 wlan ampdu frames-limit ...................... 147 SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 7 (access point) ..................188 6.1.6.4 no vap broadcast ssid (access point) ................... 189 6.1.6.5 vap wds only (access point) ....................190 6.1.6.6 no vap wds only (access point) ..................... 191 SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 9 Commands in the global configuration mode ............... 264 7.1.2.1 telnet-server .......................... 264 7.1.2.2 no telnet-server ........................265 7.1.2.3 ip echo-reply ......................... 265 7.1.2.4 no ip echo-reply ........................266 7.1.2.5 ip route ..........................267 SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 14 Syslog client ......................... 423 11.2.1 show events syslogserver ....................423 11.2.2 Commands in the Events configuration mode ..............423 11.2.2.1 syslogserver ......................... 424 11.2.2.2 no syslogserver ........................425 Index ..............................427 SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 15: Introduction
Apart from the Configuration Manual you are currently reading, the following documentation is also available from SIMATIC NET on the topic of Industrial Wireless LANs: ● Configuration Manual: SCALANCE W760 / W720 Web Based Management This Configuration Manual is intended to provide you with the information you require to commission and operate devices correctly.
Page 16 The system manual also covers connecting cables as well as a variety of plug-in connectors, lightning protectors, a power splitter and an attenuator. SIMATIC NET manuals You will find SIMATIC NET manuals on the Internet pages of Siemens Industry Online Support: ● Using the search function: support.automation.siemens.com...
Page 17: Security Information
27069465 (http://support.automation.siemens.com/WW/view/en/27069465) Security information Siemens provides automation and drive products with industrial security functions that support the secure operation of plants or machines. They are an important component in a holistic industrial security concept. With this in mind, our products undergo continuous development.
Page 18 Introduction 1.1 Security information SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 19: Description
Errors in the configuration can mean that no further operation is possible in the entire network. Note Command sets depend on the logged-on user. Changing configuration data is possible only with the "admin" login. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 20: Cli Modes
To change from the User EXEC Mode to the Privileged EXEC mode, enter the enable command. When the command executes, you will be prompted to enter the password for the "admin" user. You are logged out with the command. exit SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 21: The Cli Command Prompt
Make sure, however, that names used by the operating system or other programs are correctly written. Blank To use blanks in a text, enter the text in quotes, for example "H e l l o" SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 22: Symbols Of The Cli Commands
If you use the keyword, you need to specify exactly one of the values "A", "B" or "C". Keyword [A] [B] [C] After the keyword, enter no or several of the values "A", "B" or "C". SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 23: Interface Identifiers And Addresses
– Enter the keyword for the VLAN interface. – After a space, enter the number of the VLAN interface you assigned when you created Example: VLAN 2: interface vlan 2 SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 24 Command prompt wlan 0/X cli(config-if-wlan-0-X)# vapX 0/Y cli(config-if-vapX-0-Y)# wdsX 0/Y cli(config-if-wdsX-0-Y)# fa 0/X cli(config-if-F-0-X)# vlan$ cli(config-if-vlan-$)# The placeholders stand for the numbering of the interface. X, Y, $ SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 25: Address Types, Address Ranges And Address Masks
● Multicast addresses Layer 2 multicast addresses as used on this device use the notation of MAC addresses. For permitted address ranges, check the rules or ask your network administrator. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 26: General Cli Commands
Privileged EXEC mode that [ command ] you want to execute. Example do show cli-console-timeout Result The command from the Privileged EXEC mode will be executed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 27: End
If you are in Privileged EXEC Modus or in User EXEC Modus mode, you will be logged out. Syntax Call the command without parameters: exit Result The current mode was exited. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 28: Help Functions And Supported Input
The syntax of the command is displayed. Syntax If you call up help without parameters, you will obtain a list of all permitted commands in the current mode: help SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 29: The Command
If the display is in pages, you cannot page back. You exit the page display with the key. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 30: Completion Of Command Entries
This is only possible if all the parts of the abbreviated input can be assigned to exactly one command or to the parts of the command. Example command can be replaced by the expression show event config sh e c SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 31: Reusing The Last Used Commands
These commands are not included in the list of the Interface configuration mode. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 32 Description 2.6 General CLI commands Syntax Call the command without parameters: show history Result The list of used commands is displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 33: Configuration
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show cli-console-timeout Result The configuration for the timeout is displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 34: Show Coordinates
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show device information SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 35: Show Im
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show im Result The information is displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 36: Show Interfaces
If you do not select any parameters from the parameter list, the status and configuration of all available interfaces will be displayed. Result The status and the configuration of the selected interfaces are displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 37: Show Interfaces
If you do not select any parameter from the parameter list, the entries are displayed for all available counters. Result The counters of the selected interfaces are displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 38: Show Interface Mtu
For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 23)". If no parameters are specified, the settings for all interfaces are displayed. Result The settings are displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 39: Show Ip Interface
If you do not select any parameter from the parameter list, the configuration is displayed for all available IP interfaces. Result The configuration of the selected IP interface is displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 40: Show Pnio
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameter assignment: show lldp neighbors Result The neighborhood table is displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 41: Show Lldp Status
This command shows the versions of the hardware and software of the device. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 42: Clear Counters
The parameters have the following meaning: Parameter Description Range of values / note interface-type Type or speed of the interface Enter a valid interface. interface-id Module no. and port no. of the interface SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 43: Configure Terminal
Result You are now in the Global configuration mode. The command prompt is as follows: cli(config)# Further notes You exit the Global configuration mode with the command. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 44: Clear Line Vty
Result The console session is closed. Further notes You show the logged-on users with the command. show users SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 45: Disable
With this command, you change to the Privileged EXEC mode. Requirement You are in the User EXEC mode. The command prompt is as follows: cli> Syntax Call the command without parameters: enable SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 46: Logout
This allows you to check whether or not another node is reachable. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 47 , the restart memory factory following defaults apply: Parameters Default value size count time-out Result The messages relating to the response of the called node are displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 48: Commands In The Global Configuration Mode
Input box for the height coordinate max. 32 characters To use spaces in the entry, enter the height coordinate in quotes: coordinates height "123 456" Result The height coordinate is created. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 49: Coordinates Latitude
The latitude coordinate is created. 3.1.9.3 coordinates longitude Description With this command, you enter a longitude coordinate. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 50: Interface
Number of the addressed VLAN 1 … 4094 interface-type Type or speed of the interface Enter a valid interface. interface-id Module no. and port no. of the interface SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 51: No Interface
3.1.9.5 no interface Description With this command, you delete a logical interface. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 52: Cli-Console-Timeout
"keepalive" function is set to 120 seconds. In this case, a packet is sent every 120 seconds that keeps the connection up. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 53: No Cli-Console-Timeout
Result Automatic logout is disabled. Further notes You enable automatic logout with the command. cli-console-timeout You display the current timeout setting with the command. show cli-console-timeout SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 54: System Contact
Description With this command, you enter the location information for the system. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 55: System Name
The parameter has the following meaning: Parameter Description Range of values / note string Input box for the name max. 255 characters Result The name is created in the system. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 56: Username
The password must be at least 6 characters long. Result The password is changed. Note Changing the password in Trial mode Even if you change the password in Trial mode, this change is saved immediately. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 57: Commands In The Interface Configuration Mode
Name of the interface max. 63 characters Result The interface was assigned a name. Further notes You delete the name of the interface with the command. no alias SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 58: No Alias
With this command, you configure the duplex mode of an interface. Requirement You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 59: No Duplex
The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: no duplex Result The duplex mode of the Interface is reset to the default value. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 60: Lldp
Further notes You disable the sending or receipt of LLDP packets with the command. no lldp You display the status of LLDP with the command. show lldp status SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 61: No Lldp
The setting is configured. Further notes You enable the sending or receipt of LLDP packets with the command. lldp You display the status of LLDP with the command. show lldp status SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 62: Mtu
You can shut down the interface with the command. shutdown complete You display this setting with the command. show interface mtu You display this setting and other information with the command. show interfaces SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 63: Shutdown
Reset button. Further notes You activate the interface with the command. no shutdown You can display the status of this function and other information with the show command. interfaces SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 64: No Shutdown
The Interface is activated. Further notes You activate the interface with the command. shutdown complete You can display the status of this function and other information with the show command. interfaces SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 65: Load And Save
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show loadsave files Result The current Load&Save file information is displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 66: Show Loadsave Tftp
3.2.3.1 loadsave Description With this command, you change to the LOADSAVE configuration mode. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 67: Commands In The Loadsave Configuration Mode
With this command, you call up the possible files or delete a specific file. Requirement You are in the LOADSAVE configuration mode. The command prompt is as follows: cli(config-loadsave)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 68: Tftp Filename
Name of the file type max. 100 characters name Keyword for a file name to be assigned to the file type filename Name of the file max. 100 characters SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 69: Tftp Load
Result The file types are displayed or the file is downloaded to the device. Further notes You configure the name of the file with the command. tftp filename SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 70: Tftp Save
Description With this command, you configure the access to a TFTP server. Requirement You are in the LOADSAVE configuration mode. The command prompt is as follows: cli(config-loadsave)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 71: Password
With this command, you activate and configure the password for the user certificate. Note This command is only available in the client mode Requirement You are in the LOADSAVE configuration mode. The command prompt is as follows: cli(config-loadsave)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 72: No Password
With this command, you disable the password for the user certificate. Note This command is only available in the client mode Requirement You are in the LOADSAVE configuration mode. The command prompt is as follows: cli(config-loadsave)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 73 Name of the file type max. 100 characters Result The password for the user certificate is disabled. Further notes You enable the password for the user certificate with the command. password SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 74: Reset And Defaults
– Mode of the device ● Device restart with the factory configuration settings. Requirement You are in the Privileged EXEC mode. The command prompt is as follows: cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 75: Configuration Save & Restore
This command shows configuration settings of the device. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 76 Shows the configuration settings of the Simple Network Time Protocol http Shows the configuration settings of the Hyper- text Transfer Protocol locked-port Shows the configuration settings of the locked port function. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 77: Write Startup-Config
● The Trial mode is activated. ● You are in the Privileged EXEC mode. The command prompt is: *cli(...)# Syntax Call the command without parameter assignment: write startup-config SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 78: Commands In The Global Configuration Mode
With the command, you enable the auto save function. auto-save Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 79: No Auto-Save
You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: no auto-save Result The auto save function is disabled. The Trial mode is activated. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 80: Sinema
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 81: Sinema
With this command, you disable the SINEMA configuration interface. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameter assignment: no sinema SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 82 You enable the SINEMA configuration interface with the command. sinema You display the setting whether the SINEMA configuration interface is enabled or disabled with the command show sinema SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 83: Functions Specific To Scalance
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show web-session-timeout Result The timeout setting for the WBM is displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 84: Commands In The Global Configuration Mode
The time is configured and automatic logout is enabled. Further notes You disable automatic logoff with the command. no web-session-timeout You display the current timeout setting with the command. show web-session-timeout SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 85: No Web-Session-Timeout
This command shows the status of the signal recorder. You can call the command before, after or during the recording. Note This command is only available in the client mode. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 86: Wlan Signal-Recorder Start Sample_Number (Client)
The values are stored every 10 minutes. The file contains all values since the start of the recording. Note This command is only available in the client mode. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 87 You stop the recording early with the command. wlan signal-recorder <wlan 0/X> stop You display the status of the signal recorder and the recording with the show wlan signal- command. recorder <wlan 0/X> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 88: Wlan Signal-Recorder Stop (Client)
For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 23)". Result The recording was stopped. Further notes You start the recording with the command. wlan signal-recorder start SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 89: Wlan Signal-Recorder Display (Client)
If these files already exist, they will be overwritten. Use the command to stop the recording. wlan signal-recorder <wlan 0/X> stop During the recording, it is possible that working in the CLI becomes slower. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 90: Wlan Signal-Recorder Display Sample_Number (Client)
This parameter specifies how many 1 - 20000 measured values will be recorded. For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 23)". SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 91: Ipcf
Note The command is only available with the following device: • SCALANCE W722-1 RJ-45 (MLFB 6GK5722-1FC00-0AA0 and 6GK5722-1FC00-0AB0 (US version)) Description This command shows the settings of iPCF. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 92: Wlan Interface Configuration Mode
Privileged EXEC mode. 4.3.2.1 wlan ipcf Note The command is only available with the following device: • SCALANCE W722-1 RJ-45 (MLFB 6GK5722-1FC00-0AA0 and 6GK5722-1FC00-0AB0 (US version)) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 93: No Wlan Ipcf
With this command, you disable the iPCF mode. Requirement You are in the Interface Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-if-wlan-0-X)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 94: Ipcf-Mc
Note The command is only available with the following device: • SCALANCE W722-1 RJ-45 (MLFB 6GK5722-1FC00-0AA0 and 6GK5722-1FC00-0AB0 (US version)) Description This command shows the settings of iPCF-MC. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 95: Commands In The Wlan Configuration Mode
The command is only available with the following device: • SCALANCE W722-1 RJ-45 (MLFB 6GK5722-1FC00-0AA0 and 6GK5722-1FC00-0AB0 (US version)) Description With this command, you enable iPCF-MC on this device. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 96: No Wlan Ipcf-Mc
With this command, you disable iPCF-MC on this device. Requirement You are in the WLAN configuration mode. The command prompt is as follows: cli(config-wlan)# Syntax Call the command without parameter assignment: no wlan ipcf-mc SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 97: Wlan Ipcf-Mc Cycle-Time (Access Point)
Values or range of values Cycle time in millisec- 32 ... 512 onds (ms) Result The cycle time is configured. Further notes You display the setting with the command. show wlan ipcf-mc SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 98: Wlan Ipcf-Mc Mgmt-Scan-Period (Client)
Description Values or range of values num-of-cycles Duration 1 ... 10 Result The time is set. Further notes You display the setting with the command. show wlan ipcf-mc SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 99: System Time
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show time Result The settings for the system clock are displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 100: Show Dst Info
With this command, you configure the way in which the system time is obtained. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 101: Time Set
You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call up the command with the following parameters: time set hh:mm:ss <day (1-31)> {january|february|march|april|may|june|july|august|september|october|november|decembe <year (2000 - 2035)> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 102: Time Dst Date
You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call up the command with the following parameters: time dst date <name(16> <year (1900-2099)> begin <MMDDhh> end <MMDDhh> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 103: Time Dst Recurring
Syntax Call up the command with the following parameters: time dst recurring <name(16)> begin {<week(1-5)> | last} <weekday> <month> <hour> end {<week(1-5)> | last} <weekday> <month> <hour> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 104: No Time Dst
Call up the command with the following parameters: no time dst [<name(16>] The parameter has the following meaning: Parameter Description Range of values name Name of the entry maximum 16 characters SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 105: Ntp Client
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 106: Ntp
● If you exit the NTP configuration mode with the command, you return to the Global exit configuration mode. ● If you exit the NTP configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 107: Ntp Server
(Page 23)". Result The connection to a server is configured on the NTP client. Further notes You delete the connection to a server with the command. no ntp server SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 108: No Ntp Server
With this command, you configure the time difference between the device and the NTP server. Requirement You are in the NTP configuration mode. The command prompt is as follows: cli(config-ntp)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 109: Sntp Client
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show sntp broadcast-mode status SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 110: Show Sntp Status
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show sntp unicast-mode status SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 111: Commands In The Global Configuration Mode
Result You are now in the SNTP configuration mode. The command prompt is as follows: cli(config-sntp)# Further notes You exit the SNTP configuration modewith the command. exit SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 112: Commands In The Sntp Configuration Mode
● with sign ● without spaces ● Hours and minutes both two digits (with leading zero) Default: no time difference Result The time zone of the system time is configured. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 113: Sntp Unicast-Server
Keyword for the time after which the time of day is requested again seconds Value for the time in seconds 16 ... 16284 Result The SNTP unicast server is configured. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 114: No Sntp Unicast-Server
The SNTP unicast server is reset to the default value. Further notes You configure the setting with the command. sntp unicast-server ipv4 You display this setting and other information with the show sntp unicast–mode status command. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 115: Sntp Client Addressing-Mode
You display the settings for the unicast mode with the show sntp unicast-mode status command. You display the settings for the broadcast mode with the show sntp broadcast-mode status command. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 116 System time 5.3 SNTP client SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 117: Network Structures
Values or range of values wlan 0/X WLAN interface Enter a valid interface. For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 23)". SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 118: Show Wlan Allowed Channels
For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 23)". Result The list of wireless channels available for establishing a wireless link to the relevant WLAN interface is displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 119: Show Wlan Antennas
This command is available only in access point mode. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 120: Show Wlan Advanced-11N
Values or range of values wlan 0/X WLAN interface Enter a valid interface. For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 23)". SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 121: Show Wlan Available-Ap-List (Client)
For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 23)". Result The access points to which the client can set up a wireless link are displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 122: Show Wlan Basic
● DFS (802.11h) ● Outdoor Mode ● Max Tx Power ● TX power check: Indicates whether the current WLAN settings of the selected country violate the permitted transmit power restrictions. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 123: Show Wlan Client (Client)
The following client settings are displayed: ● MAC Mode ● Manual MAC Address ● Any SSID ● Roaming Threshold ● Background scan mode ● Background Scan Interval ● Scan Channels SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 124: Show Wlan Client-List (Access Point)
Connection ID of the client. For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 23)". Result The table with the logged-on clients is displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 125: Show Wlan Client-List-Vap (Access Point)
(access point) Description This command shows the tables with the available data transmission speeds. Note This command is available only in access point mode. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 126: Show Wlan Device
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show wlan device SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 127: Show Wlan Overlap-Ap-List (Access Point)
Values or range of values wlan 0/X WLAN interface Enter a valid interface. For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 23)". SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 128: Show Wlan Overview
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameter assignment: show wlan overview SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 129 ● Client – Radio – WLAN mode – MAC Mode – MAC Address – Operative channel – Connected BSSID – Connected SSID – HT Channel Width [Mhz] – Status SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 130: Show Wlan Statistics
For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 23)". Result The statistics are displayed for the selected WLAN interface. The range depends on the selected operating mode. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 131: Show Wlan Ssid-Table (Client)
The table with the SSIDs configured on the client and their status is displayed. 6.1.1.17 show wlan vap (access point) Description This command shows the configuration of the VAP interface. Note This command is available only in access point mode. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 132: Show Wlan Wds (Access Point)
This command is available only in access point mode. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 133: Show Wlan Wds-List (Access Point)
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call up the command with the following parameters: show wlan wds-list <wlan 0/X> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 134: Show Wlan Ip-Mapping
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show wlan ip-mapping Result The IP mapping table is displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 135: Clear Wlan Statistics
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 136: Wlan
● If you exit the WLAN configuration mode with the command, you return to the Global exit configuration mode. ● If you exit the WLAN Configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 137: Device Mode
Further notes You display the settings for the mode with the command. show wlan device See also show wlan device (Page 126) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 138: Commit Mode
The commit mode is specified. Further notes You show the settings for the commit mode with the command. show wlan device See also show wlan device (Page 126) commit wlan-settings (Page 139) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 139: Commit Wlan-Settings
With this command, you specify the country in which the device will be used. Requirement You are in the WLAN Configuration mode. The command prompt is as follows: cli (config-wlan)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 140: Commands In The Wlan Interface Configuration Mode
Global Configuration mode. ● If you exit the WLAN Interface Configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 141: Wlan Allowed Channels
Optional parameter. Use this parameter to specify the frequency band from which you want to add one or more channels to the list. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 142: Wlan Allowed Channels Only
You are in the Interface Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-if-wlan-0-X)# Syntax Call the command without parameter assignment: wlan allowed channels only SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 143: No Wlan Allowed Channels Only
You display the setting with the command. show wlan allowed channels <wlan 0/X> You enable the function with the command. wlan allowed channels only See also wlan allowed channels only (Page 142) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 144: Wlan Alternative Channel (Access Point)
You display the setting with the command. show wlan basic <wlan 0/X> You enable the DFS function with the command. wlan dfs See also wlan dfs (Page 168) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 145: Wlan Ampdu
You display the setting with the command. show wlan advanced-11n <wlan 0/X> You disable the function with the command. no wlan ampdu See also no wlan ampdu (Page 146) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 146: No Wlan Ampdu
Description With this command, you specify the maximum size of the AMPDU data packet in bytes. Note This command is available only in access point mode. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 147: Wlan Ampdu Frames-Limit
Requirement ● The IEEE 802.11n transmission standard is enabled. You are in the Interface Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-if-wlan-0-X)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 148: Wlan Antenna Additional-Attenuation
<index (1-X)> <dB(0-70)> The parameters have the following meaning: Parameter Description Values or range of values index Antenna connector X = 1 Attenuation in decibels [dB] 0...70 Default: 0 SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 149: Wlan Antenna Cable-Length
Cable length in meters [m] 0...30 Default: 0 Result The cable length is specified. Further notes You show the set cable length with the command. show wlan antennas <wlan 0/X> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 150: Wlan Antenna Gain-2-4Ghz
With this command, you specify the antenna gain of the antenna type "User defined" in the 5 GHz frequency band. With the command, check whether the maximum show wlan basic transmit power is exceeded with the setting. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 151: Wlan Antenna Type
With this command, you specify which antenna type is connected to the relevant antenna connector. Requirement You are in the Interface Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-if-wlan-0-X)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 152: Wlan Any Ssid (Client)
You are in the Interface Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-if-wlan-0-X)# Syntax Call the command without parameter assignment: wlan any ssid SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 153: No Wlan Any Ssid (Client)
You are in the Interface configuration mode of the WLAN interface. The command prompt is as follows: cli (config-if-wlan-0-X)# Syntax Call the command without parameter assignment: no wlan any ssid Result The function is disabled. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 154: Wlan Background Scan Interval (Client)
Time in milliseconds (ms) 300 ... 60 000 Default: 5000 Result The interval is specified. Further notes You show the set interval with the command. show wlan client <wlan 0/X> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 155: Wlan Background Scan Mode (Client)
" command, you specify the scan interval. scan interval Result Scanning for further access points is specified. Further notes You display the setting with the command. show wlan client <wlan 0/X> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 156: Wlan Beacon Interval (Access Point)
Length of the interval in milliseconds 40 ... 1000 (ms). Default: 100 Result The interval is specified. Further notes You show the set interval with the command. show wlan advanced <wlan 0/X> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 157: Wlan Channel (Access Point)
"0". 0 = Auto Result The channel is set. Further notes You display the setting with the command. show wlan ap <wlan 0/X> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 158: Wlan Client Mac Mode (Client)
MAC addresses connected to the Ethernet interface of the client Result The MAC address was assigned to the client. Further notes You display the setting with the command. show wlan client <wlan 0/X> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 159: Wlan Client Mac Address (Client)
MAC address of the client aa:aa:aa:aa:aa:aa Result The MAC address was assigned to the client. Further notes You display the setting with the command. show wlan client <wlan 0/X> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 160: Wlan Data Rates-11Abg Selected Only (Access Point)
You configure the data transmission speeds with the command. wlan data rate-11abg You configure the transmission standard with the command. wlan mode SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 161: No Wlan Data Rates-11Abg Selected Only (Access Point)
With this command, you enable the "Use selected data rates only" function. Only the data transmission speeds you specified with the command are used. wlan data rate-11n Note This command is available only in access point mode. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 162: No Wlan Data Rates-11N Selected Only (Access Point)
You are in the Interface Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-if-wlan-0-X)# ● The transmission standard IEEE 802.11n or IEEE 802.11n only is set. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 163: Wlan Data Rate-11Abg (Access Point)
You are in the Interface Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-if-wlan-0-X)# ● The transmission standard IEEE 802.11a/b/g/n is set. ● The "Use selected data rates only" function is enabled. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 164 You configure the transmission standard with the command. wlan mode You can reset the selection to the default setting with the wlan data rate-11abg defaults command. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 165: Wlan Data Rate-11N (Access Point)
Only the first available MCS index is assigned to the WLAN interface. The other MCS indexes are deselected. Note You need to enable at least one MCS index of the WLAN interface. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 166: Wlan Data Rate-11Abg Defaults (Access Point)
● The "Use selected data rates only" function is enabled. Syntax Call the command without parameter assignment: wlan data rate-11abg defaults Result The selection is reset to the default setting. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 167: Wlan Data Rate-11N Defaults (Access Point)
You configure the data transmission speeds with the command. wlan data rate-11n You configure the transmission standard with the command. wlan mode SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 168: Wlan Dfs
You display the setting with the command. show wlan basic <wlan 0/X> You disable the function with the command (default setting). no wlan dfs See also no wlan dfs (Page 169) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 169: No Wlan Dfs
If, for example, you enter "5", this would mean that the access point collects the packets and sends them after every fifth beacon. Note This command is available only in access point mode. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 170: Wlan Ssid-Table Edit (Client)
You are in the Interface Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-if-wlan-0-X)# Syntax Call up the command with the following parameters: wlan ssid-table edit <index (1-4)> {enable | disable| delete} [ssid] SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 171: Wlan Force Roaming Eth-Down (Access Point)
This command is available only in access point mode. Requirement You are in the Interface Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-if-wlan-0-X)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 172: No Wlan Force Roaming Eth-Down (Access Point)
The function is disabled. Further notes You display the setting with the command. show wlan advanced <wlan 0/X> You enable the function with the command. wlan force roaming eth-down SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 173: Wlan Fragmentation Threshold
(access point) Description With this command, you specify the frequency band for the WLAN interface. Note This command is available only in access point mode. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 174: Wlan Frequency Band (Client)
This command is only available in the client mode. Requirement You are in the Interface Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-if-wlan-0-X)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 175: Wlan Guard Interval (Access Point)
Requirement ● The IEEE 802.11n transmission standard is enabled. You are in the Interface Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-if-wlan-0-X)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 176: Wlan Ht Channel Width (Access Point)
This command is available only in access point mode. Requirement You are in the Interface Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-if-wlan-0-X)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 177: Wlan Hw-Retries
WLAN chip itself when it tries to repeat an unacknowledged packet immediately. Requirement You are in the Interface Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-if-wlan-0-X)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 178: Wlan Max Tx-Power
) of the selected country. TX Power Check Requirement You are in the Interface Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-if-wlan-0-X)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 179: Wlan Mode (Access Point)
This command is available only in access point mode. Requirement You are in the Interface Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-if-wlan-0-X)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 180: Wlan Mode (Client)
<wlan 0/X> 6.1.5.44 wlan mode (client) Description With this command, you specify the transmission standard. Note This command is only available in the client mode. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 181 Is not downwards compatible with IEEE 802.11a and IEEE 802.11g Depending on the current configuration, some settings are not possible. In this case, a message to this effect is displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 182: Wlan Outdoor
You display the setting with the command. show wlan basic <wlan 0/X> You disable the function with the command (default setting). no wlan outdoor See also no wlan outdoor (Page 183) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 183: No Wlan Outdoor
With this command, you configure the aging time for the list of overlapping access points. If an access point is inactive for longer than the set time, it is removed from the list. Note This command is available only in access point mode. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 184: Wlan Roaming Threshold (Client)
This command is only available in the client mode. Requirement You are in the Interface Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-if-wlan-0-X)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 185: Wlan Rts-Cts Threshold
Call up the command with the following parameters: wlan rts-cts threshold < bytes(1-2346)> The parameter has the following meaning: Parameters Description Values or range of values bytes Size specified in bytes 1...2346 Default: 2346 SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 186: Commands In The Vap Interface Configuration Mode
This command is available only in access point mode. Requirement You are in the Interface Configuration mode of the VAP interface. The command prompt is as follows: cli (config-if-vapX-0-Y)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 187: Vap Ssid (Access Point)
This command is available only in access point mode. Requirement You are in the Interface Configuration mode of the VAP interface. The command prompt is as follows: cli (config-if-vapX-0-Y)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 188: Vap Broadcast Ssid (Access Point)
You are in the Interface Configuration mode of the VAP interface. The command prompt is as follows: cli (config-if-vapX-0-Y)# Syntax Call the command without parameter assignment: vap broadcast ssid SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 189: No Vap Broadcast Ssid (Access Point)
The function is disabled. Further notes You display the setting with the command. show wlan vap <vap X 0/Y> You enable the function with the command (default setting). vap broadcast ssid SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 190: Vap Wds Only (Access Point)
<vap X 0/Y> You disable the function with the command (default setting). no vap wds only See also no vap wds only (access point) (Page 191) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 191: No Vap Wds Only (Access Point)
You display the setting with the command. show wlan vap <vap X 0/Y> You enable the function with the command. vap wds only See also vap wds only (access point) (Page 190) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 192: Commands In The Wds Interface Configuration Mode
The WDS ID is used for communication. With the " " com- wds partner wds id mand, you specify the WDS ID. Result The type of communication is specified. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 193: Wds Partner Mac (Access Point)
Description mac-address MAC address of the communications partner Result The MAC address is specified. Further notes You display the setting with the command. show wlan wds <wdsX 0/Y> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 194: Wds Partner Wds-Id (Access Point)
The WDS ID is specified. Further notes You display the setting with the command. show wlan wds <wdsX 0/Y> See also wds partner id-type (access point) (Page 192) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 195: Wds Connection Over (Access Point)
For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 23)". Result The VAP interface is set. Further notes You display the setting with the command. show wlan wds <wdsX 0/Y> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 196: Vlan
For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 23)". If you do not select any parameter from the parameter list, the entries are displayed for all available interfaces. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 197: Show Mac-Address-Table
If you do not select any parameter from the parameter list, the entries are displayed for all available interfaces. Result The entries of the MAC addresses table are displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 198: Show Mac-Address-Table Count
● In "base bridge-mode", the mode for the device is set to "transparent". You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 199: Show Vlan
This command shows the specific information for all or a selected VLAN. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 200: Show Vlan Device Info
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show vlan device info Result The global information is displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 201: Show Vlan Learning Params
This command shows the VLAN-specific information for ports. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 202: Commands In The Global Configuration Mode
MAC address list that was learned dynamically is deleted again after a certain time. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 203: No Mac-Address-Table Aging
Syntax Call the command without parameters: no mac-address-table aging Result The "Aging" function is disabled. Further notes You enable the "Aging" function with the command. mac-address-table aging SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 204: Vlan
The command prompt is as follows: cli(config-vlan-$$$)# Further notes You delete the VLAN with the command. no vlan You can display information about the VLAN with the command. show vlan SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 205: No Vlan
IEEE 802.1D for the Spanning Tree protocol or according to IEEE 802.1Q for a virtual bridged LAN. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 206: Mgmt Vlan
● In " ", the mode for the device is set to base bridge-mode dot1q-vlan You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 207: Commands In The Interface Configuration Mode
Description With this command, you configure which types of frames the interface accepts. Requirement You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 208: Switchport Access Vlan
Call up the command with the following parameters: switchport access vlan <vlan-id(1-4094)> The parameter has the following meaning: Parameter Description Range of values / note vlan-id Number of the addressed VLAN 1 ... 4094 SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 209: No Switchport Access Vlan
You configure the setting with the command. switchport access vlan You can display the status of this function and other information with the show vlan port command. config SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 210: Switchport Ingress-Filter
6.2.3.5 no switchport ingress-filter Description With this command, you disable the ingress filter. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 211: Switchport Priority Default
Description Range of values / note Value for the priority default 0 ... 7 Default: 0 Result The setting for the default priority of the interface is configured. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 212: No Switchport Priority Default
(PVID) for it. If a received frame has no VLAN tag, it has a tag added with the VLAN ID specified here and is sent according to the switch rules for the port. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 213: No Switchport Pvid
The default value is 1. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: no switchport pvid SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 214: Commands In The Vlan Configuration Mode
6.2.4.1 name Description With this command, you assign a name to the VLAN. Requirement You are in the VLAN Configuration mode. The command prompt is as follows: cli(config-vlan-$$$)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 215: No Name
Syntax Call the command without parameters: no name Result The name of the VLAN is deleted. Further notes You assign the VLAN a name with the command name SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 216: Ports
You are in the VLAN Configuration mode. The command prompt is as follows: cli(config-vlan-$$$)# Syntax Call up the command with the following parameters: ports [<interface-type><0/a-b,0/c,...>] [<interface-type><0/a-b,0/c,...>] untagged<interface-type> <0/a-b,0/c,...> [<interface-type><0/a-b,0/c,...>] [all] forbidden<interface-type><0/a-b,0/c,...> [<interface-type><0/a-b,0/c,...>] [name<vlan-name>] SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 217: No Ports
Description With this command, you reset the ports for a VLAN. Requirement You are in the VLAN Configuration mode. The command prompt is as follows: cli(config-vlan-$$$)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 218 (Page 23)". Result The ports are reset. Further notes You display details of the function with the command. show vlan You reset the setting with the command. no ports SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 219: Spanning Tree
Shows the blocked ports pathcost method Shows whether 16-bit (short) or 32 bit (long) values are used in the calcula- tion Result The settings for the spanning tree function are displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 220: Show Spanning-Tree Active
[detail] The parameter has the following meaning: Parameter Description detail Shows settings in detail Result The settings for the active ports of the spanning tree function are displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 221: Show Spanning-Tree Bridge
Shows the priority of the bridge detail Shows detailed information about the spanning tree settings of the interface Result The settings for the spanning tree function of the bridge are displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 222: Show Spanning-Tree Detail
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call up the command with the following parameters: show spanning-tree interface <interface-type><interface-id> [{cost|priority|portfast|rootcost|restricted-role| restricted-tcn|state|stats|detail}] SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 223: Show Spanning-Tree L2T-Edge
This command is available only in access point mode. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 224: Show Spanning-Tree Mst Configuration
The settings of an instance of the Multiple Spanning Tree protocol are displayed. Further notes You display the general settings for the Spanning Tree Protocol with the show spanning-tree command. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 225: Show Spanning-Tree Mst Interface
For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 23)". Result The settings are displayed. Further notes You display the general settings for the Spanning Tree Protocol with the show spanning-tree command. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 226: Show Spanning-Tree Root
Shows the priority of the bridge detail Shows detailed information about the root bridge Result The settings of the root bridge for the spanning tree function are displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 227: Clear Spanning-Tree Counters
The Spanning Tree Protocol is used to monitor a LAN for redundant connections. These are blocked and reactivated when necessary if there are changes to the network topology. With this command, you enable the spanning tree function. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 228: No Spanning-Tree
You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: no spanning-tree Result The spanning tree function is disabled. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 229: Spanning-Tree Compatibility
The version is compatible with the Default: enabled Rapic Spanning Tree protocol The version is compatible with the Multiple Spanning Tree protocol Result The compatibility version of the protocol is selected. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 230: No Spanning-Tree Compatibility
Further notes You configure the setting with the command. spanning-tree compatibility You can display the status of this function and other information with the show spanning tree command. detail SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 231: Spanning-Tree L2T-Auto-Edge
With this command, you disable automatic detection of an end device at layer 2 tunnel ports. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: no spanning-tree l2t-auto-edge SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 232: Spanning-Tree L2T-Edge
The setting is enabled. Further notes You disable the setting with the command. no spanning-tree l2t-edge You can display the status of this function with the command. show spanning-tree l2t-edge SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 233: No Spanning-Tree L2T-Edge
You are in the Global configuration mode. ● MSTP is enabled ● Base bridge mode: 802.1Q VLAN Bridge ● Compatibility mode: MSTP The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 234: Spanning-Tree Mst Instance-Id Root
The parameters have the following meaning: Parameter Description Range of values / note instance-id Keyword for the instance instance-id Number of the instance 1 ... 64 SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 235: No Spanning-Tree Mst Instance-Id Root
Call up the command with the following parameters: spanning-tree mst{instance-id<instance-id(1-64)>}root The parameters have the following meaning: Parameter Description Range of values instance-id Keyword for the instance instance-id Number of the instance 1 ... 64 SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 236: Spanning-Tree Mst Max-Hops
You can reset the setting for the maximum number of nodes to the default with the command. spanning-tree mst max-hops You display this setting and other information with the show spanning tree mst command. configuration SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 237: No Spanning-Tree Mst Max-Hops
The bridge with the highest priority becomes the root bridge. The lower the value, the higher the priority. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 238: No Spanning-Tree Priority
With this command, you reset the priority of the device back to the default value. The default value is 32768. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 239: Time Settings For The Spanning Tree Protocol
BPDUs max-age becomes invalid. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 240 You can reset the time to the default with the command (time settings). no spanning-tree You display these settings and other information with the commands that start with show spanning tree ... SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 241 Further notes You configure the time with the command (time settings). spanning-tree You display these settings and other information with the commands that start with show spanning tree ... SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 242: Commands In The Interface Configuration Mode
Requirement You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 243 With each call of the command, you can configure precisely one property. If you want to configure several properties, call the command several times. Result The selected property is configured. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 244: No Spanning-Tree
Keyword for the costs of the port for calculating the lowest-cost path. disable Enables the interface for spanning tree. link-type Connection status of the following network segment SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 245: Spanning-Tree Auto-Edge
You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: spanning-tree auto-edge Result The automatic discovery of a bridge on the interface is enabled. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 246: No Spanning-Tree Auto-Edge
Description With this command, you configure the BPDU transmit status for a port. Requirement You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 247: Spanning-Tree Bpdu-Receive
Range of values / note enabled BPDU packets are received at the port Default: enabled disabled BPDU packets are ignored at the port Result The BPDU receive status is enabled or disabled. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 248: Spanning-Tree Bpdu-Transmit
The BPDU transmit status has switched over. Further notes You can display the status of this function and other information with the show spanning tree command with the option. interface detail SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 249: Spanning-Tree Mst
Note Configure multiple properties With each call of the command, you can configure precisely one property. If you want to configure several properties, call the command several times. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 250: No Spanning-Tree Mst
Keyword for the costs of the port for calculating the lowest-cost path. port-priority Keyword for the priority of the interface disable Enables the interface for multiple spanning tree. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 251: Spanning-Tree Mst Hello-Time
The parameter has the following meaning: Parameter Description Range of values / note seconds Time after which the bridge sends its 1 ... 2 configuration frames (BPDUs) Default: 2 SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 252: No Spanning-Tree Mst Hello-Time
You can configure the setting for the hello time with the spanning-tree mst hello-time command. You display this setting and other information with the commands that start with show spanning tree ... SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 253: Commands In The Mstp Configuration Mode
"0" vlan Keyword for a VLAN connection vlan-range Range of VLANs assigned to an in- enter the range limts with a hy- stance phen or blank SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 254: No Instance
If you do not specify a VLAN, the MST instance is deleted. Result The assignment of a VLAN to an MST instance is canceled or the MST instance is deleted. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 255: Name
You delete the name of the MST region with the command. no name You display this setting and other information with the show spanning tree mst command. configuration SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 256: No Name
Description With this command, you assign a revision number to the MST region. Requirement You are in the MSTP Configuration mode. The command prompt is as follows: cli(config-mst)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 257: No Revision
The command prompt is as follows: cli(config-mst)# Syntax Call the command without parameters: no revision Result The revision number of the MST region is reset to the default value. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 258 You assign a revision number to the MST region with the command. revision You display this setting and other information with the show spanning tree mst command. configuration SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 259: Network Protocols
Enter a valid interface. interface-id Module no. and port no. of the interface For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 23)". SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 260: Show Dcp Server
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call up the command with the following parameters: show ip route[{<ip-address>[<mask>]|connected|static}] SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 261: Show Ip Telnet
The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show ip telnet Result The admin status and the port number of the Telnet server are displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 262: Show Ip Dns
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show ip dns cache Result The content of the DNS cache is displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 263: Show Ip Dns Name-Server
The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show ip dns statistics Result Information about the communication with the DNS server is displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 264: Commands In The Global Configuration Mode
Call the command without parameters: telnet-server As default the function is "enabled". Result The Telnet server is enabled. Further notes You disable the Telnet server with the command. no telnet-server SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 265: No Telnet-Server
(echo reply). With this command, you enable the ICMP echo reply messages. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 266: No Ip Echo-Reply
Further notes You change the setting with the command. ip echo-reply You can display the setting of this function and other information with the show ip command. information SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 267: Ip Route
With this command, you delete a static entry from the IP routing table. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 268: Dcp Server
Parameter Description Range of values / note read-only only reading is permitted on the DCP server read-write reading and writing is permitted on the Default: read-write DPC server SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 269: No Dcp Server
Call the command without parameters: no dcp server Result The DCP server is disabled. Further notes You enable and configure the DCP server with the command. dcp server SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 270: Ip Domain Lookup
You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: no ip domain lookup Result The DNS client of the device is disabled. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 271: Ip Name-Server
For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 23)". Result The IP address and, if specified, the index for a DNS server has been set. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 272: No Ip Name Server
Only resource records of type A (IPv4 address of a host) are supported. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 273: Commands In The Interface Configuration Mode
With this command, you assign an IP address to a VLAN interface. Requirement ● Interface is a router port You are in the Interface configuration mode of VLAN. The command prompt is as follows: cli(config-if-vlan-$$$)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 274: No Ip Address
With this command, you delete the assignment of an IP address to a VLAN interface. Requirement You are in the Interface configuration mode of VLAN. The command prompt is as follows: cli(config-if-vlan-$$$)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 275: Ip Address Dhcp
With this command, the VLAN interface obtains the IP address via DHCP. Requirement You are in the Interface Configuration mode of VLAN. The command prompt is as follows: cli(config-if-vlan-$$$)# Syntax Call the command without parameters: ip address dhcp SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 276: Dcp Forwarding
The parameters have the following meaning: Parameter Description block DCP frames are discarded forward DCP frames are forwarded Default: forward Result The forwarding behavior of the interface for DCP frames is configured. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 277: Dhcp Client
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show ip dhcp client SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 278: Renew Dhcp
You can display the statistical information of the DHCP client with the show ip dhcp client command. stats You show the statistical information and the configuration of the IP interface with the show ip command. interface SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 279: Commands In The Global Configuration Mode
Result The DHCP config file request option is enabled. Further notes You disable the DHCP config file request option with the no ip dhcp config-file-request command. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 280: No Ip Dhcp Config-File-Request
You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call up the command with the following parameters: ip dhcp client mode {mac|client-id<client-id>|sysname} SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 281: Dhcp Server
IPv4 address bands and the corresponding DHCP options. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 282: Show Ip Dhcp-Server Bindings
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameter assignment: show ip dhcp-server bindings Result The information is displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 283: Commands In The Global Configuration Mode
● You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameter assignment: ip dhcp-server Result The DHCP server is enabled. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 284: No Ip Dhcp-Server
Syntax Call the command without parameter assignment: no ip dhcp-server Result The DHCP server is disabled. Further notes You enable the DHCP server with the command. ip dhcp-server SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 285: Ip Dhcp-Server Icmp-Probe
Syntax Call the command without parameter assignment: ip dhcp-server icmp-probe Result The function is enabled. Further notes You disable the function with the command. no ip dhcp-server icmp-probe SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 286: No Ip Dhcp-Server Icmp-Probe
Syntax Call the command without parameter assignment: no ip dhcp-server icmp-probe Result The function is disabled. Further notes You enable the function with the command. ip dhcp-server icmp-probe SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 287: Ip Dhcp-Server Pool
Only ID = 1 is supported. show-interface-options Displays the possible options for the interface. For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 23)". SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 288: No Ip Dhcp-Server Pool
The parameter has the following meaning: Parameter Description Range of values / note pool-id ID of the addressed IPv4 address band 1 ... 5 Only ID = 1 is supported. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 289: Commands In The Dhcppool Configuration Mode
IPv4 address or extend the lease time of the existing IPv4 address. Requirement You are in the DHCPPOOL configuration mode. The command prompt is as follows: cli(config-dhcp-pool-<ID>)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 290: Network
With this command you configure the IPv4 address band from which the DHCP client receives any IPv4 address. Requirement You are in the DHCPPOOL configuration mode. The command prompt is as follows: cli(config-dhcp-pool-<ID>)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 291: Option (Ip Address)
With this command you configure the DHCP options 3, 6 and 66 that contain an IPv4 address as DHCP parameter. The DHCP options 3, 6 and 66 are created automatically when the IPv4 address band is created. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 292 You configure the DHCP option 67 with the command. option value-string You configure all other DHCP options with the command. option value-hex You configure the interface with the command. set interface SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 293: Option Value-Hex
The following DHCP options are not sup- ported: 50 - 60 • • dhcp-param DHCP parameter in hexadecimal Enter a valid hexadecimal value. Format: XXXXX e.g. C0A86402 Result The DHCP option is configured. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 294: Option Value-String
Range of values / note option-code Code of the DHCP option 67 - Boot file name dhcp-param Name of the boot file Result The DHCP option 67 is configured. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 295: No Option
The parameter has the following meaning: Parameter Description Range of values / note option-code Code of the DHCP option Enter a valid number. Result The specified DHCP option is deleted. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 296: Pool-Enable
If the IPv4 address band is activated, no DHCP options (option ...) and static assignments (static leases) can be configured. Further notes You display the setting with the command. show ip dhcp-server pools You disable the setting with the command. no pool-enable SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 297: No Pool-Enable
Result The setting is disabled. Further notes You display the setting with the command. show ip dhcp-server pools You enable the setting with the command. pool-enable SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 298: Set-Interface
The interface is assigned. Before the IPv4 address band can be used, it still needs to be activated. Further notes You display the setting with the command. show ip dhcp-server pools You enable the IPv4 address band with the command. pool-enable SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 299: Static-Lease Mac
You display the setting with the command. show ip dhcp dhcp-server bindings You disable the IPv4 address band with the command. no pool-enable You delete the assignment with the command. no static-lease mac SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 300: No Static-Lease
Range of values / note mac-address Unicast MAC address Specify a valid MAC address. Result The assignment is deleted. Further notes You configure the assignment with the command. static-lease mac SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 301: Snmp
This command shows the details of the configured of SNMP communities. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 302: Show Snmp Engineid
This command shows the configured SNMP filters. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 303: Show Snmp Group
This command shows the rights of the configured SNMP groups. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 304: Show Snmp Inform Statistics
With this command, you display the configured SNMP notification types. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 305: Show Snmp Targetaddr
This command shows the configured SNMP target parameters. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 306: Show Snmp User
This command shows the settings for the SNMP tree views. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 307: Commands In The Global Configuration Mode
Syntax Call the command without parameters: snmpagent Result The SNMP agent function is enabled. Further notes You disable the SNMP agent function with the command. no snmpagent SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 308: No Snmpagent
With this command, you configure whether all SNMP queries or only SNMPv3 queries are processed. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 309: Snmp Access
Range of values / note GroupName Name of the group to which access is max. 32 characters configured Selects the version of the protocol • used • • SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 310 You display the access configurations for SNMP groups with the show snmp group access command. You display the configured SNMP tree views with the command. show snmp viewtree SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 311: No Snmp Access
You display the access configurations for SNMP groups with the show snmp group access command. You display the configured SNMP tree views with the command. show snmp viewtree SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 312: Snmp Community Index
• nonvolatile The settings are retained after a restart If optional parameters are not specified when configuring a community, the default values apply. Result The settings are configured. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 313: No Snmp Community Index
You show the details of an SNMP community with the command. show snmp community You show the status information of the SNMP communication with the command. show snmp SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 314: Snmp Filterprofile
... and " " means: Access permitted excluded ● ..and " " means: Access permitted included ● ..and " " means: Access denied excluded SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 315: No Snmp Filterprofile
Result The filter is deleted. Further notes You create a filter with the command. snmp filterprofile You display the created filter with the command. show snmp filter table SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 316: Snmp Group
You display the created SNMP groups with the command. show snmp group You display the created SNMP user with the command. show snmp user SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 317: No Snmp Group
You change the details of an SNMP group with the command. snmp group You display the created SNMP groups with the command. show snmp group You display the created SNMP user with the command. show snmp user SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 318: Snmp Notify
The settings are lost after a restart (non-volatile): • nonvolatile The settings are retained after a restart Result The details of the SNMP notifications are configured. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 319: No Snmp Notify
You display the configured SNMP notifications with the command. show snmp notif You display the configured SNMP target addresses with the show snmp targetaddr command. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 320: Snmp Targetaddr
Keyword for the maximum number of attempts to obtain a response to an inform request message RetryCount Number of attempts 1 ... 3 taglist Keyword for • TagIdentifier • none SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 321: No Snmp Targetaddr
Description With this command, you delete the SNMP target address. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 322: Snmp Targetparams
Range of values / note ParamName Name of the SNMP parameter max. 32 characters user Keyword for the user name UserName Value for the user name max. 32 characters SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 323 You configure the user profile with the command. snmp user You configure a filter with the command. snmp filterprofile You display the list of users with the command. show snmp user SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 324: No Snmp Targetparams
Description With this command, you block write access for SNMPv1 and SNMPv2 PDUs. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 325: No Snmp V1-V2 Readonly
Result Write access for SNMPv1 and SNMPv2 PDUs is enabled. Further notes You block write access for SNMPv1 and SNMPv2 PDUs with the snmp v1-v2 readonly command. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 326: Snmp User
The saved settings are used after a restart If optional parameters are not specified when configuring an SNMP user, the defaults values apply. Result The details of the SNMP user are configured. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 327: No Snmp User
The details of the SNMP user are deleted. Further notes You change the settings with the command. snmp user You display the configured users with the command. show snmp user SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 328: Snmp View
• nonvolatile The settings are retained after a restart (default) If optional parameters are not specified when configuring, the default values apply. Result The SNMP view is configured. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 329: No Snmp View
The SNMP view is deleted. Further notes You configure a view with the command. snmp view You display the configured view trees with the command. show snmp viewtree SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 330: Smtp Client
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show events sender email SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 331: Show Events Smtp-Port
● If you exit the EVENTS configuration mode with the command, you return to the exit Global configuration mode. ● If you exit the EVENTS configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 332: Smtp-Server
For information on addresses and interfaces, refer to the section "Addresses and interface names (Page 23)". Result An entry for the SMTP server is configured. Further notes You delete an SMTP server entry with the command. no smtp-server SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 333: No Smtp-Server
For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 23)". Result The SMTP server entry is deleted. Further notes You configure an e-mail server entry with the command. smtp-server SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 334: Sender Mail-Address
Description With this command, you reset the e-mail name of the sender. Requirement You are in the EVENTS configuration mode. The command prompt is as follows: cli(config-events)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 335: Smtp-Port
An SMTP port is configured. Further notes You can reset the setting to the default with the command. no smtp-port You display the setting with the command. show smtp-port SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 336: No Smtp-Port
The SMTP port is reset to the default value. Further notes You configure the setting with the command. smtp-port You display the setting with the command. show smtp-port SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 337: Http Server
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 338: Ip Http
Description With this command, you disable HTTP on the device. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 339: Https Server
The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show ip http secure server status Result The status, cipher suite and version of the HTTPS server are displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 340: Show Ssl Server-Cert
With this command, you display the IP ARP table. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 341: Ssh Server
If you do not select any parameter from the parameter list, the IP ARP table is displayed. Result The IP ARP table is displayed. SSH server This section describes commands of the Secure Shell (SSH) Server. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 342: Show Ip Ssh
Description With this command, you enable the SSH protocol on the device. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 343: No Ssh-Server
Syntax Call the command without parameters: no ssh-server Result The SSH protocol is disabled on the device. Further notes You enable the SSH protocol with the command. ssh-server SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 344 Network protocols 7.9 SSH server SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 345: Load Control
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show mac-address-table aging-time Result The time is displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 346: Show Mac-Address-Table Aging-Status
With this command, you configure the aging of a dynamically learned entry in the MAC address list. Note Addresses with light data traffic For addresses with low data traffic, it is recommended to enter a higher value for the aging. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 347 The value of the aging of a dynamically learned entry is configured. Further notes You can reset the setting to the default with the command. no mac-address-table aging-time You display the setting with the command. show mac-address-table aging-time SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 348 Load control 8.1 Dynamic MAC aging SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 349: Layer 3 Functions
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show nat Result The configuration and the translation list are displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 350: Commands In The Global Configuration Mode
This command is only available in the client mode Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 351: Commands In The Nat Configuration Mode
A maximum of 60 entries are possible. Note This command is only available in the client mode Requirement You are now in the NAT Configuration mode. The command prompt is as follows: cli(config-nat)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 352 You show the NAT configuration and the translation list with the command. show nat You delete entries with the command. no nat See also show nat (client) (Page 349) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 353: No Nat (Client)
The entry is deleted from the translation list. Further notes You show the NAT configuration and the translation list with the command. show nat You configure entries with the command. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 354: Nat Local Ip Address (Client)
The local IP address of the Ethernet interface is configured. Further notes You show the NAT configuration and the translation list with the command. show nat See also show nat (client) (Page 349) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 355: Nat Interface (Client)
You configure the MAC mode with the command. wlan client mac mode You show the NAT configuration and the translation list with the command. show nat See also show nat (client) (Page 349) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 356: No Nat Interface (Client)
TCP / UDP connection is deleted from the translation table when this time has elapsed. Note This command is only available in the client mode SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 357 You show the NAT configuration and the translation list with the command. show nat You delete the period of time with the command. no nat timeout See also show nat (client) (Page 349) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 358: No Nat Timeout (Client)
You show the NAT configuration and the translation list with the command. show nat You configure the time with the command. nat timeout See also show nat (client) (Page 349) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 359: Security And Authentication
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: whoami Result The user name of the logged in user is displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 360: Show Users
Example: wlan mode ● wlan mode (access point): The function can only be used with access points. ● wlan mode (client): The function can only be used with clients. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 361: Show Wlan Security
The settings are displayed. 10.2.2 show wlan security ap-radius-authenticator (Access Point) Description This command shows the settings of the RADIUS server. Note This command is available only in access point mode. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 362: Show Wlan Security Keys
This command shows a table with the WEP key of the device. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 363: Commands In The Wlan Configuration Mode
This command is available only in access point mode. Requirement You are in the WLAN Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-wlan)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 364: No Wlan Security Ap-Radius-Authenticator
This command is available only in access point mode. Requirement You are in the WLAN Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-wlan)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 365: Wlan Security Ap-Radius-Authenticator Address
This command is available only in access point mode. Requirement You are in the WLAN Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-wlan)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 366: Wlan Security Ap-Radius-Authenticator Max-Retransmit
This command is available only in access point mode. Requirement You are in the WLAN Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-wlan)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 367: Wlan Security Ap-Radius-Authenticator Port-Number
This command is available only in access point mode. Requirement You are in the WLAN Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-wlan)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 368: Wlan Security Ap-Radius-Authenticator Primary
This command is available only in access point mode. Requirement You are in the WLAN Configuration mode and the "wlan security ap-radius-authenticator address" is configured. The command prompt is as follows: cli (config-wlan)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 369: No Wlan Security Ap-Radius-Authenticator Primary
This command is available only in access point mode. Requirement You are in the WLAN Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-wlan)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 370: Wlan Security Ap-Radius-Authenticator Reauth-Interval
This command is available only in access point mode. Requirement ● Local time management is active. You are in the WLAN Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-wlan)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 371: Wlan Security Ap-Radius-Authenticator Reauth-Mode
This command is available only in access point mode. Requirement You are in the WLAN Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-wlan)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 372: Wlan Security Ap-Radius-Authenticator Shared-Secret
(Access Point) (Page 361) 10.2.4.10 wlan security ap-radius-authenticator shared-secret Description With this command, you configure the password for the RADIUS server. Note This command is available only in access point mode. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 373: Commands In The Wlan Interface Configuration Mode
Global Configuration mode. ● If you exit the WLAN Interface Configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 374: Wlan Security Authentication (Client)
If iPCF or iPCF-MC mode is enabled, only "Open System" with the encryption method AES is supported in the security settings. Requirement You are in the Interface Configuration mode of the WLAN interface. The command prompt is as follows: cli (config-if-wlan-0-X)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 375 The type of authentication is specified. Further notes You display the settings with the command. show wlan security <wlan 0/X> See also no wlan security encryption (client) (Page 385) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 376: Wlan Security Cipher (Client)
Code 4). In contrast to the weak WEP encryption, TKIP uses changing keys derived from a main key. Note The encryption method "TKIP" is not available with the transmission standards "802.11n" and "802.11n only". SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 377: Wlan Security Default-Key (Client)
Index of the key table 1...4 Default: 1 Result The WEP key is specified. Further notes You display the settings with the command. show wlan security <wlan 0/X> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 378: Wlan Security Dot1X Check-Server-Certificate (Client)
<wlan 0/X> You disable the validity check with the no wlan security dot1x check-server-certificate command (default setting). See also no wlan security dot1x check-server-certificate (client) (Page 379) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 379: No Wlan Security Dot1X Check-Server-Certificate (Client)
You display the settings with the command. show wlan security <wlan 0/X> You enable the validation with the wlan security dot1x check-server-certificate command. See also wlan security dot1x check-server-certificate (client) (Page 378) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 380: Wlan Security Dot1X Eap-Authentication-Type (Client)
TLS tunnel, MS-CHAPv2 is used for internal au- thentication. • peap Protected Extensible Authentication Protocol: Al- ternative draft protocol of IETF for EAP-TTLS Result The authentication method is specified. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 381: Wlan Security Dot1X Username (Client)
Result The user name is specified. Further notes You display the settings with the command. show wlan security <wlan 0/X> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 382: Wlan Security Dot1X Password (Client)
Result The password is specified. Further notes You display the settings with the command. show wlan security <wlan 0/X> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 383: Wlan Security Edit Key
Enter the WEP or AES key. Result The WEP or AES key is inserted in the key table. Further notes You display the settings with the command. show wlan security <wlan 0/X> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 384: Wlan Security Encryption (Client)
You configure which WEP key is used with the wlan security default-key (Client) command. See also no wlan security encryption (client) (Page 385) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 385: No Wlan Security Encryption (Client)
<wlan 0/X> You enable the encryption with the command. wlan security encryption See also wlan security encryption (client) (Page 384) wlan security authentication (client) (Page 374) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 386: Wlan Security Wpa-Psk-Passphrase (Client)
WPA(2) key 8..63 ASCII exactly 64 hex Result A WPA(2) key is specified. Further notes You display the settings with the command. show wlan security <wlan 0/X> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 387: Commands In The Vap Interface Configuration Mode
If iPCF or iPCF-MC mode is enabled, only "Open System" with the encryption method AES is supported in the security settings. Requirement You are in the Interface Configuration mode of the VAP interface. The command prompt is as follows: cli (config-if-vapX-0-Y)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 388 WPA and WPA2 authentication without a RADIUS server Result The type of authentication is specified. Further notes You display the settings with the command. show wlan security <vapX 0/Y> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 389: Vap Security Cipher (Access Point)
Code 4). In contrast to the weak WEP encryption, TKIP uses changing keys derived from a main key. Note The encryption methods "WEP" and "TKIP" are not available with the transmission standards "802.11n" and "802.11n only". SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 390: Vap Security Default-Key (Access Point)
Values or range of values index Index of the key table 1...4 Result The WEP key is specified. Further notes You display the settings with the command. show wlan security <vapX 0/Y> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 391: Vap Security Encryption (Access Point)
With the command, you configure the WEP key vap security default-key (Access Point) used for encryption. See also no vap security encryption (access point) (Page 392) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 392: No Vap Security Encryption (Access Point)
You display the settings with the command. show wlan security <vapX 0/Y> You enable the encryption with the command. vap security encryption See also vap security encryption (access point) (Page 391) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 393: Vap Security Wpa-Group-Key-Update-Interval (Access Point)
The key will not be renewed. seconds When the time expires (second), 30 ... 36000 the key is renewed. Result The time for renewal of the key is specified. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 394: Vap Security Wpa-Psk-Passphrase (Access Point)
WPA(2) key. 8..63 ASCII exactly 64 hex Result A WPA(2) key is specified. Further notes You display the settings with the command. show wlan security <vapX 0/Y> SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 395: Vap Communication With Own-Vap (Access Point)
<vapX 0/Y> You disable the function with the command. no vap communication with own-vap See also no vap communication with own-vap (access point) (Page 396) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 396: No Vap Communication With Own-Vap (Access Point)
You display the settings with the command. show wlan security <vapX 0/Y> You enable the function with the command. vap communication with own-vap See also vap communication with own-vap (access point) (Page 395) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 397: Vap Communication With Ethernet (Access Point)
<vapX 0/Y> You disable the function with the command. no vap communication with ethernet See also no vap communication with ethernet (access point) (Page 398) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 398: No Vap Communication With Ethernet (Access Point)
You display the settings with the command. show wlan security <vapX 0/Y> You enable the function with the command. vap communication with ethernet See also vap communication with ethernet (access point) (Page 397) SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 399: Management Access Control List
For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 23)". Result The information about the configuration of the authorized managers is displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 400: Commands In The Global Configuration Mode
Keyword for a an interface description interface-type Type or speed of the interface Enter a valid interface. 0/a-b,0/c,... Module no. and port no. of the interface vlan Keyword for a VLAN connection SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 401 You delete an interface for access of an authorized manager with the no authorized-manager command. ip-source You show the information about the configuration of the authorized managers with the show command. authorized-manager SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 402: No Authorized-Manager Ip-Source
You configure the interfaces and protocols via which an authorized manager is allowed to access the device with the command. authorized-manager ip-source You show the information about the configuration of the authorized managers with the show command. authorized-manager SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 403: Diagnostics
With this command, you show the information about successful or failed authentication attempts. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 404: Show Events Config
This command shows the degree of severity of an event ("Info", "Warning" or "Critical") starting at which a notification (sending of an e-mail, entry in the Syslog table, entry in the Syslog file) is generated. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 405: Show Events Faults Config
● Monitoring of the network connections for a change in the connection status Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 406: Show Events Faults Status
The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show events faults status Result A table with the status messages of the error monitoring functions is displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 407: Show Fault Counter
The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show logbook Call up the command with the following parameters: show logbook { info | warning | critical } SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 408: Show Power-Line-State
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show power-line-state Result The status of the power supply is displayed. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 409: Show Rmon
Description With this command, you delete the content of the logbook. Requirement You are in the Privileged EXEC mode. The command prompt is as follows: cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 410: Clear Logbook
With this command, you acknowledge (delete) the messages of the "Cold/Warm start" event. Requirement You are in the Privileged EXEC mode. The command prompt is as follows: cli# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 411: Commands In The Global Configuration Mode
With this command, you change to the EVENTS configuration mode. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: events SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 412: Commands In The Events Configuration Mode
Call the command without parameters: add log <log entry> The parameter has the following meaning: Parameter Description Range of values / note log entry Entry in the logbook max. 150 characters SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 413: Client Config
Further notes You display the status of the events and the clients with the command. show events config You disable a client with the command. no client config SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 414: No Client Config
The following events or message types are available: ● Message if there is cold or warm restart ● Message when there is a status change on a physical interface SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 415 Message if there is an incorrect login power-change Message when there is a status change in the power supply faultstate-change Message when there is a status change in the error monitoring SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 416 With each command call, you can only select one message type and one client. If you want to process several message types or clients, it may be more efficient to first select the option and then disable individual elements. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 417: No Event Config
(only available if supported by the device) All messages logtable Client that processes the logbook entries syslog Client that sends the messages to the log server email Client that sends the e-mails SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 418: Severity
Specifies the threshold value for enter- ing system event messages in the log table. syslog Specifies the threshold value for enter- ing system event messages in the Syslog file. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 419: No Severity
With this command, you disable the setting for the threshold values for the sending of system event notifications. Requirement You are in the EVENTS Configuration mode. The command prompt is as follows: cli (config-events) # SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 420: Link
With this command, you configure and enable the monitoring of the physical network connections for cable breaks or for pulling of the connector. Requirement You are in the EVENTS Configuration mode. The command prompt is as follows: cli(config-events)# SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 421: No Link
The parameters have the following meaning: Parameters Description Range of values The message when establishing a connection is disabled down The message when a connection is down is disa- bled SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 422: Send Test Mail
Result An e-mail according to the currently configured SMTP settings is sent. Further notes You can display the current SMTP settings with the command. show events smtp-server SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 423: Syslog Client
● If you exit the EVENTS configuration mode with the command, you return to the exit Global configuration mode. ● If you exit the EVENTS configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 424: Syslogserver
Further notes You disable the setting with the command. no syslogserver You can display the status of this function and other information with the show events config command. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 425: No Syslogserver
The settings for the Syslog server are disabled. Further notes You enable the setting with the command. syslogserver You can display the status of this function and other information with the show events config command. SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 426 Diagnostics 11.2 Syslog client SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 427: Index
165 no cli-console-timeout, 53 wlan data rates-11abg selected only, 160, 166 wlan data rates-11n selected only, 161, 167 wlan dtim, 169 wlan force roaming eth-down, 171 SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 428 270 no dcp server, 269 ip domain used server, 272 delete, 67 ip echo-reply, 265 device mode, 137 no ip echo-reply, 266 disable, 45 SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 429 423 show history, 31 option, 291 show in, 35 no option, 295 show interface mtu, 38 option value-hex, 293 show interfaces, 36 show interfaces ... counters, 37 SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 430 220 client config, 413 show spanning-tree bridge, 221 no client config, 414 show spanning-tree detail, 222 snmp access, 309 show spanning-tree interface, 222 no snmp access, 311 SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 431 237 vap security default-key, 390 spanning-tree priority, 237 vap security encryption, 391 no spanning-tree priority, 238 no vap security encryption, 392 vap security wpa-group-key-update-interval), 393 SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...
Page 432 162 wlan dfs, 168 no wlan dfs, 169 wlan dtim, 169 wlan force roaming eth-down, 171 no wlan force roaming eth-down, 172 wlan fragmentation threshold, 173 SCALANCE W760/W720 to IEEE 802.11n Command Line Interface Configuration Manual, 11/2014, C79000-G8976-C351-03...

This manual is also suitable for:

Scalance w720

Siemens SCALANCE W760 Configuration Manual

1 Introduction

2 Description

3 Configuration

4 Functions Specific to SCALANCE

5 System Time

6 Network Structures

Quick Links

Related Manuals for Siemens SCALANCE W760

Summary of Contents for Siemens SCALANCE W760