Table of Contents
Advertisement
Quick Links
PATTERSON-KELLEY
THERMIFIC
DIRECT VENT/SEALED COMBUSTION
GAS-FIRED BOILER
Supplement to the standard Installation and
Owner's Manual (TBIG - Latest Edition)
Installation Date
100 Burson Street, P.O. Box 458,
East Stroudsburg, PA 18301
Telephone: (877) 728-5351, Facsimile: (570) 476-7247
www.pkboilers.com
Patterson-Kelley
P.O. Box 458, 100 Burson Street
East Stroudsburg, PA 18301
Telephone: (570) 421-7500, Facsimile: (570) 476-7247
®
DIRECT VENT/
SEALED
COMBUSTION
DIRECT VENT/
SEALED
COMBUSTION
DIRECT VENT/
SEALED
COMBUSTION
DIRECT VENT/
SEALED
COMBUSTION
DIRECT VENT/
SEALED
COMBUSTION
DIRECT VENT/
SEALED
COMBUSTION
DIRECT VENT/
SEALED
COMBUSTION
DIRECT VENT/
SEALED
COMBUSTION
DIRECT VENT/
DVSCM-02
Advertisement
Table of Contents
Related Manuals for Patterson-Kelley DVSCM-02
Summary of Contents for Patterson-Kelley DVSCM-02
- Page 1 100 Burson Street, P.O. Box 458, East Stroudsburg, PA 18301 Telephone: (877) 728-5351, Facsimile: (570) 476-7247 www.pkboilers.com Patterson-Kelley P.O. Box 458, 100 Burson Street East Stroudsburg, PA 18301 Telephone: (570) 421-7500, Facsimile: (570) 476-7247 DVSCM-02 DIRECT VENT/ SEALED COMBUSTION DIRECT VENT/ SEALED COMBUSTION DIRECT VENT/...
-
Page 2: Table Of Contents
The same features which permit this boiler to achieve high-efficiency performance make it unlike most other boilers of this general size, so it is important to understand how this boiler operates. -
Page 3: Introduction
® Thermific Gas-Fired Boiler 1.0 INTRODUCTION Direct vent (ANSI Z21.13) is a closed system method of ducting the combustion air directly from the outside of the building into the inlet compartment of the burner, and a sealed exhaust vent from the combustion chamber to the outdoors. -
Page 4: Purpose And Scope Of This Manual
"TBIG" latest edition. 2.0 SAFETY Refer to the manual for the standard Thermific® Gas- Fired Boiler for safety information applicable to this equipment. Safety information applicable only to the direct vent option appears below. Danger! -
Page 5: Installation
Auxiliary Control Panel to operate the inlet damper assembly. The inlet damper assembly and control panel will prevent the flow of cold air through the boiler during the off cycle and prevent freeze up and "off cycle" losses. The use of these two items is optional. -
Page 6: Inlet Duct Assembly At The Boiler
Transition Duct (Sidewall installation shown.) The boiler is equipped with a special collar attached to the air inlet opening on the back of the unit (at the blower housing on Series 700, 1000, and 1200; at the back of the cabinet on Series 1500, 1700 and 2000.). -
Page 7: Inlet Damper And Auxiliary Control Panel (Optional)
3.2.5.1 Field Wiring to Auxiliary Control Panel The auxiliary control panel controls the inlet damper (if used). The auxiliary control panel does not have to be mounted on or near the boiler; it can be remotely mounted. Use 16GA MTW Wire for all field wiring. See... -
Page 8: Exhaust Vent Connection At The Boiler
Condensate Drain To sewer trap or condensate pump. At the outlet of the boiler, an adjustable or fixed length (minimum 2 feet for clearance from inlet duct; maximum 3 feet for proper lift) section may be utilized. This section must be secured to the outlet collar by a minimum of 4 sheet metal screws spaced at approximately 90 degree intervals. -
Page 9: Equivalent Length Of Fittings
® Thermific Gas-Fired Boiler Whichever termination is chosen, it must be double wall vent certified under UL 1738, or ULC-636. When installing a sidewall exhaust system the termination must be backed by a metal plate secured to the wall as shown in the figure. -
Page 10: Rooftop Installations
* Dimension shown above is based on 12" round ductwork. A minimum clearance of 26 inches is required on the left side of the boiler to permit the connection of the air inlet duct to the boiler. Flue Gas Outlet 4' min. -
Page 11: Operation
44" Min. * Dimension shown above is based on 12" round ductwork. A minimum of 44 inches is required behind the boiler to fit the inlet and exhaust connections. The figure above suggests a duct arrangement using standard duct pieces that will maintain this minimum clearance of 44 inches. -
Page 12: Combustion Air Requirement, Scfm
® Thermific Gas-Fired Boiler When the chart is completed, set up your boiler's combustion to the corresponding information at the temperature relative during the time of the start up. Enter your 100º F % Oxygen operational range. Important: measure combustion air temperature at the unit;... -
Page 13: Wiring Diagrams
® Thermific Gas-Fired Boiler 6.0 WIRING DIAGRAMS 6.1 O 700, 1000, 1200 ERIES Wiring Diagram Page 11 Wiring Diagrams... -
Page 14: On-Off Iri Series 700, 1000, 1200
® Thermific Gas-Fired Boiler 6.1 O 700, 1000, 1200 ERIES Logic Diagram Page 12 Wiring Diagrams... - Page 15 ® Thermific Gas-Fired Boiler IRI S 700, 1000, 1200 ERIES Wiring Diagram Page 13 Wiring Diagrams...
- Page 16 ® Thermific Gas-Fired Boiler IRI S 700, 1000, 1200 ERIES Logic Diagram Page 14 Wiring Diagrams...
-
Page 17: Lo-Hi Lo
® Thermific Gas-Fired Boiler Wiring Diagram Page 15 Wiring Diagrams... - Page 18 ® Thermific Gas-Fired Boiler Logic Diagram Page 16 Wiring Diagrams...
-
Page 19: Lo-Hi-Lo Iri
® Thermific Gas-Fired Boiler Wiring Diagram Page 17 Wiring Diagrams... - Page 20 ® Thermific Gas-Fired Boiler Logic Diagram Page 18 Wiring Diagrams...
-
Page 21: On-Off Series 1500, 1700, 2000
® Thermific Gas-Fired Boiler Wiring Diagrams 1500, 1700, 2000 ERIES Wiring Diagram Page 19... - Page 22 ® Thermific Gas-Fired Boiler Wiring Diagrams 1500, 1700, 2000 ERIES Logic Diagram Page 20...
-
Page 23: On-Off Iri Series 1500, 1700, 2000
® Thermific Gas-Fired Boiler Wiring Diagrams IRI S 1500, 1700, 2000 ERIES Wiring Diagram Page 21... - Page 24 ® Thermific Gas-Fired Boiler Wiring Diagrams IRI S 1500, 1700, 2000 ERIES Logic Diagram Page 22...
-
Page 25: Auxiliary Control Panel
® Thermific Gas-Fired Boiler Wiring Diagrams 6.2 A UXILIARY ONTROL ANEL 6.2.1 On-Off Auxiliary Control Panel Page 23... - Page 26 Page 24...