SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. AVOID AN X-RAY As for the places which need special attentions, Safety is secured against an X-ray by consider- they are indicated with the labels or seals on the ing about the cathode-ray tube and the high cabinet, chassis and parts.
TABLE OF CONTENTS SERVICING NOTICES ON CHECKING ..................A1-1 A1-1 HOW TO ORDER PARTS ......................IMPORTANT ..........................A1-1 TABLE OF CONTENTS ......................A2-1 A3-1~A3-5 GENERAL SPECIFICATIONS ....................DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF ANODE CAP ....................B1-1 2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ..........B2-1, B2-2 SERVICE MODE LIST ........................
GENERAL SPECIFICATIONS CRT Size / Visual Size 27 inch / 676.6mmV System CRT Type Flat Deflection degree Magnetic Field BV/BH +0.45G/0.18G Color System NTSC Speaker 2 Speaker Position Front Side Size 1.8 x 3.9 Inch Impedance Sound Output 5.0+5.0 W 10%(Typical) 4.0+4.0 W NTSC3.58+4.43 /PAL60Hz...
Page 5
GENERAL SPECIFICATIONS On Screen Menu Display Menu Type Icon Picture Contrast Brightness Color Tint Sharpness Reset Sound Bass Treble Balance BBE On/Off Stable Sound On/Off Surround On/Off Set Up Closed Caption PIP Source TV/CATV Auto CH Memory Add/ Delete Mode Color Temperature Picture Preference Option...
Page 6
GENERAL SPECIFICATIONS G-10 Remote Unit RC-GR Control Glow in Dark Remocon Back Light Remocon Format Toshiba Custom Code TV:40-BFh Power Source Voltage(D.C) UM size x pcs UM-3 x 2 pcs Total Keys Keys Keys Power 100 /+10 CH Up CH Down...
Page 7
Features Auto Degauss Auto Shut Off Canal+ CATV Anti-theft Rental Memory(Last CH) Memory(Last Volume) V-Chip Type USA,Toshiba Type Auto Search CH Allocation Just Clock Function CH Label VM Circuit Full OSD Premiere Comb Filter Vertical Contour Correction Auto CH Memory...
Page 8
GENERAL SPECIFICATIONS G-13 Interface Switch Front Power System Select Main Power SW Sub Power Channel Up Channel Down Volume Up Volume Down Rear AC/DC TV/CATV Selector Degauss Main Power SW Indicator Power Yes(RED) Stand-by On Timer Terminals Front Video Input = VIDEO3 Audio Input = VIDEO3 RCA x 2 S Input...
DISASSEMBLY INSTRUCTIONS 3. After one side is removed, pull in the opposite direction to 1. REMOVAL OF ANODE CAP remove the other. Read the following NOTED items before starting work. NOTE After turning the power off there might still be a potential Take care not to damage the Rubber Cap.
DISASSEMBLY INSTRUCTIONS When IC starts moving back and forth easily after REMOVAL AND INSTALLATION OF desoldering completely, pickup the corner of the IC using a FLAT PACKAGE IC tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.) REMOVAL NOTE Put the Masking Tape (cotton tape) around the Flat...
Page 11
DISASSEMBLY INSTRUCTIONS INSTALLATION When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin-tip Take care of the polarity of new IC and then install the new Soldering Iron. (Refer to Fig. 2-8.) IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily.
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 1 second. Set Key Remocon Key Operations Releasing of V-CHIP PASSWORD and LOCK PASSWORD.
ELECTRICAL ADJUSTMENTS 1. ADJUSTMENT PROCEDURE 2. BASIC ADJUSTMENTS Read and perform these adjustments when repairing the 2-1: CONSTANT VOLTAGE circuits or replacing electrical parts or PCB assemblies. Place the set with Aging Test for more than 5 minutes. CAUTION Set condition is AV MODE without signal. •...
Page 14
ELECTRICAL ADJUSTMENTS 2-6: VERTICAL POSITION 2-12: E/W PARABOLA Receive the crosshatch signal from the Pattern Generator. Receive the monoscope pattern. Using the remote control, set the brightness and contrast Set the screen mode to 4:3. Using the remote control, set the brightness and contrast to normal position.
Page 15
ELECTRICAL ADJUSTMENTS 2-15: BRIGHT CENT Receive the monoscope pattern. (RF Input) Using the remote control, set the brightness and contrast to normal position. Activate the adjustment mode display of Fig. 1-1 and press the channel button (16) on the remote control to select "BRI CENT".
ELECTRICAL ADJUSTMENTS 3-3: STATIC CONVERGENCE 3. PURITY AND CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. NOTE Receive the crosshatch pattern from the color bar Turn the unit on and let it warm up for at least 30 generator.
Page 26
SOUND SCHEMATIC DIAGRAM (MAIN PCB) FROM/TO TUNER/STEREO R302 AUDIO_OUT_L 2.7K 1/4W R301 AUDIO_OUT_R 2.7K 1/4W C309 0.039 L IN VD L ONT R305 C323 R307 C325 0.0033 0.033 Tone Volume SURR 2.2K Balance Control R313 Control /MUTE MODE control R IN Vref R OUT R306...
Page 31
COMB/FILTER SCHEMATIC DIAGRAM (COMB PCB) C1553 L1504 0.01 B C1556 C1558 22uH C1562 0305 0.01 B 0.01 B C1506 BUFFER 0.01 B Q1511 10P CH KTA1504S_Y_RTK BUFFER C1535 C1509 L1501 BUFFER R1508 Q1513 4.9 4.9 Q1510 KTC3875S_Y_RTK 0.01 B 470 1/10W 15uH KTC3875S_Y_RTK C1536...
Page 32
6DB AMP SCHEMATIC DIAGRAM (AV PCB) 6dB AMP IC790 NJM2246L FROM/TO AV S790 (WHITE) S791 (RED) S792 (YELLOW) S793 (BLUE) CP790 CP791 003P-2100 003P-2100 PCB250 TECB33 NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
WAVEFORMS MICON SOUND 50Ns 1.0V 500mV 50ns 1.0V 500mV 20µs 1.0V 100mV 20µs 1.0V 100mV DEFLECTION 20µs 200V 1.0V 2.0V NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
Page 34
WAVEFORMS 10µs 2.0V 20µs 200mV 20µs 200mV CRT/SVM 10µs 10µs NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.