Xconfiguration Video Output Connector [N] Resolution; Xconfiguration Video Presentation Defaultsource; Xconfiguration Video Selfview Default Mode; Xconfiguration Video Selfview Default Fullscreenmode - Cisco TelePresence MX700 Reference Manual
Hide thumbs
Also See for TelePresence MX700:
- Reference manual (241 pages) ,
- Administrator's manual (141 pages) ,
- Installation manual (32 pages)
Table of Contents
Advertisement
Cisco TelePresence MX700 and MX800
Introduction
xConfiguration Video Output Connector [n] Resolution
This setting applies to Connector [2..3] for MX800 Single, and Connector [3] for MX700 and
MX800 Dual.
Define the resolution and refresh rate for the connected screen.
Requires user role: ADMIN
Default value: Auto
USAGE:
xConfiguration Video Output Connector
where
Resolution
: Auto/1280_720_50/1280_720_60/1920_1080_50/1920_1080_60/1920_1200
_50/1920_1200_60
Auto: The system will automatically try to set the optimal resolution based on negotia-
tion with the connected monitor.
1280_720_50: The resolution is 1280 x 720, and the refresh rate is 50 Hz.
1280_720_60: The resolution is 1280 x 720, and the refresh rate is 60 Hz.
1920_1080_50: The resolution is 1920 x 1080, and the refresh rate is 50 Hz.
1920_1080_60: The resolution is 1920 x 1080, and the refresh rate is 60 Hz.
1920_1200_50: The resolution is 1920 x 1200, and the refresh rate is 50 Hz.
1920_1200_60: The resolution is 1920 x 1200, and the refresh rate is 60 Hz.
xConfiguration Video Presentation DefaultSource
Define which video input source to use as a default presentation source. This setting may be
used by the API and 3rd party user interfaces, but is not relevant when using Touch 10 or the
TRC6 remote control.
Requires user role: USER
Default value: 3
USAGE:
xConfiguration Video Presentation DefaultSource:
where
DefaultSource
: 1/2/3/4
The video input source to use as default presentation source.
Cisco TelePresence MX700 and MX800 API Reference Guide CE8.0, FEBRUARY 2016.
D15335.02
About the API
xConfiguration
xConfiguration
Resolution:
n
Resolution
DefaultSource
xCommand
xConfiguration Video Selfview Default Mode
Define if the main video source (self-view) shall be displayed on screen after a call. The position
and size of the self-view window is determined by the Video Selfview Default PIPPosition and
the Video Selfview Default FullscreenMode settings respectively.
Requires user role: ADMIN
Default value: Current
USAGE:
xConfiguration Video Selfview Default Mode:
where
Mode
: Off/Current/On
Off: self-view is switched off when leaving a call.
Current: self-view is left as is, i.e. if it was on during the call, it remains on after the call;
if it was off during the call, it remains off after the call.
On: self-view is switched on when leaving a call.
xConfiguration Video Selfview Default FullscreenMode
Define if the main video source (self-view) shall be shown in full screen or as a small picture-
in-picture (PiP) after a call. The setting only takes effect when self-view is switched on (see the
Video Selfview Default Mode setting).
Requires user role: ADMIN
Default value: Current
USAGE:
xConfiguration Video Selfview Default FullscreenMode:
where
FullscreenMode
: Off/Current/On
Off: self-view will be shown as a PiP.
Current: The size of the self-view picture will be kept unchanged when leaving a call, i.e.
if it was a PiP during the call, it remains a PiP after the call; if it was fullscreen during the
call, it remains fullscreen after the call.
On: The self-view picture will be shown in fullscreen.
86
API Reference Guide
xStatus
Appendices
Mode
FullscreenMode
Copyright © 2016 Cisco Systems, Inc. All rights reserved.
Advertisement
Chapters
Table of Contents
