Related Manuals for Whirlpool AGS 646/WP
Summary of Contents for Whirlpool AGS 646/WP
- Page 1 ELECTRIC OVEN AGS 646/WP Installation, user and maintenance instruction Page 1 di 15 Instruction AGS 646-WP- rev9 english ed.05...
-
Page 2: Table Of Contents
CONTENTS SCHEMATIC REPRESENTATION Pag. 3 GENERAL INFORMATION AND SAFETY INSTRUCTIONS Pag. 3 General safety instructions pag. 3 Appliance specifications pag. 4 Legal requirements, technical regulations and directives pag. 4 Special conditions required for the place of installation pag. 4 Technical data pag. -
Page 3: Schematic Representation
SCHEMATIC REPRESENTATION GENERAL INFORMATION AND SAFETY INSTRUCTIONS GENERAL SAFETY INSTRUCTIONS Carefully read the safety instructions in this booklet, as they will give you important information about how to install, maintain, and use the appliance safely. Keep this booklet in a safe place. These appliances are intended for professional use in a restaurant environment, and must therefore be used only by trained staff. -
Page 4: Appliance Specifications
CAUTION!: The isolator must be placed near the appliance, in a position easily accessible by the user. TECHNICAL DATA Model Dimensions Nominal Voltage Power Cable section WxDxH (mm) AGS 646/WP 600x548x581 230 V. / 16 A. 3,7 kW 3x2.5mm Page 4 di 15 Instruction AGS 646-WP- rev9 english ed.05... -
Page 5: Design Characteristics
DESIGN CHARACTERISTICS Load-bearing structure of stainless steel with 4 feet adjustable in height. Digital controls: start-stop / temperature / timer / interior light – heating is provided by two shielded resistors equipped with a motor-fan. Temperature is controlled electronically, and goes ahead from room temperature to 450°C. -
Page 6: Installation
Producers and importers fulfil their responsibility for environmentally compatible recycling, treatment and disposal both directly and by joining a collective scheme. Place the oven on a surface able to support the weight, with the left side at least 50 cm from the wall or from other appliances. -
Page 7: Commissioning Test And Putting Into Service
Check that the earthing system is working effectively. The appliance must also be included in an equipotential bonding system. Connection is through the terminal (marked with the international symbol) provided on the back of the oven, using a cable of nominal section less than 4 mm2. This connection is applied between all installed appliances and the short-circuit stable earthing system. -
Page 8: User Instructions
In the event of a malfunction in the appliance, disconnect all power supplies and call technical support. If a fault occurs repeatedly, technical support must be called. USER INSTRUCTIONS Before switching on and using the appliance for the first time, it is essential to carefully clean the oven interior and any accessories that come into contact with food. -
Page 9: Setting The Temperature
When point symbol (4) is lit, it indicates that the time is set in hours/minutes; when off, the setting is in minutes/seconds. To indicate that the timer is running, point symbol (5) flashes at the rate of one flash per second. To set the time, use buttons (7), (+) to increase and (-) to decrease. -
Page 10: Cooking
Other dishes: Insert the grid holders before switching the oven on. Oven AGS 646/WP is suitable for cooking all types of food. Set the desired temperature and insert the food when the oven is hot. IMPORTANT!: For even cooking and to protect the appliance over time, temperature should not go over 300°C when cooking on a pan or grid (without the PIZZA cylinders). -
Page 11: Precautions If Not Using For Long Periods
PRECAUTIONS IF NOT USING FOR LONG PERIODS If not using for long periods, clean the appliance thoroughly and remove any residues, then dry perfectly. We recommend leaving the door slightly open to allow air to circulate inside the oven and preserve the lining. -
Page 12: Reserved For Technical Support
RESERVED FOR TECHNICAL SUPPORT SERVICE CONNECTIONS Connector Description Notes TTL serial port for use by Requires a suitable adaptor for Technical Support for updating connection to a Personal the software Computer Activates Test mode when Jumper for selecting Test mode inserted Factory programming Reserved for the manufacturer... -
Page 13: Power Connections
POWER CONNECTIONS Terminal Name Description Notes CN5-1 Common contact Max. capacity 10A Controlo relay for upper resistor CN5-2 Normally Open contact Max. capacity 10A Control relay for upper resistor CN5-3 Common contact control relay for Max. capacity 10A lower resistor CN6-1 Normally Open contact Max. -
Page 14: Control Panel
Press button 12 (fig. 2) for the interior light (SW11) to light up all parts of the display. Remove jumper CN9 to exit AUTO-TEST mode and automatically go into analog channel display mode. See also “Resetting the thermocouple offset”. To go back to normal working mode, press the timer START/STOP button. - Page 15 The manufacturer will not accept any liability whatsoever if the regulations and instructions described in this manual are not strictly observed. WHIRLPOOL EUROPE S.r.l. V.le Guido Borghi, 27 I – 21025 Comerio – VA...