Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
KD-DV5506/KD-DV5505/
KD-DV5504
Installation/Connection Manual
GET0606-008B
[A/UI]
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does
not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
WARNINGS
• DO NOT install any unit or wire any cable in a location where;
– it may obstruct the steering wheel and gearshift lever operations.
– it may obstruct the operation of safety devices such as air bags.
– it may obstruct visibility.
• DO NOT operate the unit while driving.
• If you need to operate the unit while driving, be sure to look around carefully.
• The driver must not watch the monitor while driving.
If the parking brake is not engaged, "DRIVER MUST NOT WATCH THE MONITOR WHILE
DRIVING." appears on the monitor, and no playback picture will be shown.
– This warning appears only when the parking brake lead is connected to the parking brake
system built in the car.
To prevent short circuits, we recommend that you disconnect the battery's negative terminal and make all
electrical connections before installing the unit.
• Be sure to ground this unit to the car's chassis again after installation.
Notes:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio
dealer.
• It is recommended to connect speakers with a maximum power of more than 50 W (both at the
rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 50 W,
change <AMP GAIN> setting to prevent the speakers from being damaged (see page 39 of the
INSTRUCTIONS).
• To prevent short circuits, cover the terminals of the UNUSED
leads with insulating tape.
• The heat sink becomes very hot after use. Be careful not to
touch it when removing this unit.
Parts list for installation and connection
If any item is missing, consult your JVC car audio dealer immediately.
A / B Hard case/Control panel
D Trim plate
F AV mini plug cable
×
I Mounting bolt (M5
20 mm)
L Remote controller
Heat sink
C Sleeve
E Power cord
G Washer (ø5)
H Lock nut (M5)
J Rubber cushion
K Handles
M Battery
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. If you have any questions or require information
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Do the required electrical connections.
When using the optional stay
Stay (option)
Fire wall
Dashboard
Screw (option)
Install the unit at an
angle of less than 30˚.
Removing the unit
Before removing the unit, release the rear section.
Insert the two handles, then pull them as
illustrated so that the unit can be removed.
*
1
When you stand the unit, be careful not to damage the fuse on the rear.
*
2
Not supplied for this unit.
1
0409DTSMDTJEIN
EN
© 2009 Victor Company of Japan, Limited
Bend the appropriate tabs to hold
the sleeve firmly in place.
When installing the unit without
using the sleeve
In a Toyota car for example, first remove the car
radio and install the unit in its place.
Flat head screws
(M5 × 8 mm)
*
2
*
2
Bracket
Pocket
Flat head screws
(M5 × 8 mm)
*
2
Bracket
Note:
When installing the unit on the mounting
bracket, make sure to use the 8 mm-long screws.
If longer screws are used, they could damage the
unit.
*
2
Advertisement
Related Manuals for JVC KD-DV5506
Summary of Contents for JVC KD-DV5506
- Page 1 Do the required electrical connections. Notes: • Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer. • It is recommended to connect speakers with a maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω...
-
Page 2: Electrical Connections
ELECTRICAL CONNECTIONS PRECAUTIONS on power supply and speaker connections: • DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be seriously damaged. • BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car. Typical connections Before connecting: Check the wiring in the vehicle carefully. - Page 3 Y-connector Remote lead (blue with white stripe) To the remote lead of other equipment or automatic antenna if any Rear speakers JVC Amplifier Signal cord Front speakers Not supplied for this unit. Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint (if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.
- Page 4 When connecting the external components, refer also to the manuals supplied for the components and adapters. CAUTION: Before connecting the external components, make sure that the unit is turned off. You can connect the following JVC components to the CD changer jack. JVC component Model name CD changer (CD-CH) CH-X1500, etc.