Table of Contents
Advertisement
Bluetooth Module : MB8811C1
[top]
This MB8811C1 Module is compatible with Bluetooth specification version 4.0. MB8811C1 is a fully integrated RF,
baseband controller etc.
SPECIFICATION
Main Chips
Standards
Frequency Band
Tx Power
Rx Sensitivity
Distance
Power Voltage
Environmental Range
Modulation mode
Communication method
[bottom]
CSR8811
Bluetooth 4.0+BLE
2402 ~ 2480 MHz
7mW
< -70dBm (BER 0.1%)
< 10m (open space)
3.3V
18.6ⅹ31.2 ⅹ3.4 mm
Operation temperature : -10 ~ +70℃
GFSK, 8DPSK, ≤κ/4 DQPSK
FHSS
Advertisement
Table of Contents
Related Manuals for LG MB8811C1
Summary of Contents for LG MB8811C1
- Page 1 Bluetooth Module : MB8811C1 [top] [bottom] This MB8811C1 Module is compatible with Bluetooth specification version 4.0. MB8811C1 is a fully integrated RF, baseband controller etc. SPECIFICATION Main Chips CSR8811 Standards Bluetooth 4.0+BLE Frequency Band 2402 ~ 2480 MHz Tx Power Rx Sensitivity <...
- Page 2 Pin define(TOP PIN MAP) Pin Name Description Bluetooth UART Clear to Send.Active-low clear. Positive Input for the internal regulator (3.0 ~ 3.6V) Bluetooth UART Serial Output. Bluetooth UART Request to Send. Active-low request. Bluetooth UART Serial Input. 6,7,8,12 Ground. I2C interface DATA I2C interface Clock RESET Reset if low.
- Page 3 Pin define(BOTTOM PIN MAP) Pin Name I/O Description Bluetooth UART Clear to Send.Active-low clear. Positive Input for the internal regulator (3.0 ~ 3.6V) Bluetooth UART Serial Output. Bluetooth UART Request to Send. Active-low request. Bluetooth UART Serial Input. 6,7,8,12 Ground. I2C interface DATA I2C interface Clock RESET...
- Page 4 Dimension Mark Dimension Mark Dimension Mark Dimension Mark Dimension Mark Dimension 18.60±0.3 3.90±0.2 2.0±0.2 6.4±0.2 3.4±0.2 31.20±0.3 8.40±0.2 1.9±0.2 4.9±0.2 5.0±0.2 9.70±0.3 2.0±0.3 0.8±0.1 2.6±0.2 5.1±0.2 (Unit : mm)
-
Page 5: Current Consumption
Electrical Characteristics Conditions : VDD = 3.3V, Ta = 25 ℃, unless otherwise noted. Absolute Maximum Ratings Parameter Unit Power Supply Voltage : VDD -0.4V 3.6V Storage Temperature ℃ Recommended Operating Conditions Parameter Unit Power Supply Voltage 3.0V 3.6V Operation Temperature ℃... - Page 6 General Performance Parameter Condition Unit Frequency Range Normal 2402 2480 Transmitter Performance Parameter Condition Unit Transmit Power Normal Power density Normal 20dB bandwidth Normal 1000 ±2MHz Adjacent channel power ±3MHz = 2441MHz) ±4MHz 30MHz ~ 1GHz 1GHz ~ 12.75GHz Out-band Spurious Emission 1.8GHz ~ 1.9GHz 5.1GHz ~ 5.3GHz ∆F1...
- Page 7 * reference document : BlueTest Instruction Manual.pdf Conformity Assessment Display Company name: MCSLogic Model : MCS Bluetooth Smart Device Module (MB8811C1) Manufacture Year : 2014. . Manufacturer / Manufacture Country : MCSLogic / Korea “Operation of the radio equipment may cause propagation interference, and so the life-saving...
- Page 8 STATEMENT and Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
- Page 9 19-1, Cheongho-ri Jinwi-myeon, Pyeongtaek-si,Gyeonggi-do, 451-713, Korea 「依據低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均 不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干 擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機 設備之干擾。」 任一平台若裝置本模組，其平台標籤須標示 “內建藍芽模組 NCC:XXXXXXXXXXX” This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 20 cm is maintained between the antenna and users, and ...
- Page 10 19-1, Cheongho-ri Jinwi-myeon, Pyeongtaek-si,Gyeonggi-do, 451-713, Korea End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: BEJ9QK-DMMB8811C1”, “contains IC: 2703H-DMMB8811C1”.