Sony CDX-MP40 Installation/Connections
Car audio: fm/am compact disc player
Hide thumbs
Also See for CDX-MP40:
- Service manual (66 pages) ,
- Installation/connections (5 pages) ,
- Product manual (2 pages)
Advertisement
Available languages
Available languages
Quick Links
FM/AM
Compact Disc
Player
Installation/Connections
Installation/Connexions
CDX-MP40
Sony Corporation © 2003
1
1
2
4
5
Equipment used in illustrations (not supplied)
Appareils utilisés dans les illustrations (non fournis)
Front speaker
Haut-parleur avant
Rear speaker
Haut-parleur arrière
Power amplifier
Amplificateur de puissance
3-251-806-11 (1)
Printed in Korea
3
4
2
CD/MD changer
Changeur de CD/MD
Rotary commander RM-X4S
Satellite de commande RM-X4S
2
A
AUDIO OUT FRONT
AUDIO OUT REAR
B
BUS AUDIO IN
BUS CONTROL IN
Source selector*
Sélecteur de source*
XA-C30
Cautions
• This unit is designed for negative ground 12 V DC
operation only.
• Do not get the wires under a screw, or caught in
moving parts (e.g. seat railing).
• Before making connections, turn the car ignition
off to avoid short circuits.
• Connect the yellow and red power input leads
only after all other leads have been connected.
• Run all ground wires to a common ground
point.
• Be sure to insulate any loose unconnected wires
with electrical tape for safety.
• The use of optical instruments with this product
will increase eye hazard.
Notes on the power supply cord (yellow)
• When connecting this unit in combination with
other stereo components, the connected car
circuit's rating must be higher than the sum of
each component's fuse.
• When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (1)
• The numbers in the list are keyed to those in the
instructions.
• The bracket 1 and the protection collar 3 are
attached to the unit before shipping. Before
mounting the unit, use the release keys 5 to
remove the bracket 1 and the protection collar 3
from the unit. For details, see "Removing the
protection collar and the bracket (4)" on the
reverse side of the sheet.
• Keep the release keys 5 for future use as they
are also necessary if you remove the unit from
your car.
Caution
Handle the bracket 1 carefully to avoid injuring
your fingers.
1
Catch
Note
Before installing, make sure that the catches on both
sides of the bracket 1 are bent inwards 2 mm (
3
/
32
the catches are straight or bent outwards, the unit
will not be installed securely and may spring out.
BUS AUDIO IN
BUS CONTROL IN
* not supplied
non fourni
Connection example (2)
Notes (2-A)
• Be sure to connect the ground cord before connecting
the amplifier.
• If you connect an optional power amplifier and do not
use the built-in amplifier, the beep sound will be
deactivated.
Tip (2-B-
)
For connecting two or more CD/MD changers, the source
selector XA-C30 (optional) is necessary.
Connection diagram (3)
1
To a metal surface of the car
First connect the black ground lead, then connect
the yellow and red power input leads.
2
To the power antenna control lead or power
supply lead of antenna booster amplifier
Notes
• It is not necessary to connect this lead if there is no
power antenna or antenna booster, or with a
manually-operated telescopic antenna.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see "Notes on the control and
power supply leads."
3
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4
To the interface cable of a car telephone
5
To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the +12
V power (battery) terminal which is energized at
all times.
Be sure to connect the black ground lead to a
metal surface of the car first.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see "Notes on the control and
power supply leads."
6
To the +12 V power terminal which is energized
at all times
Be sure to connect the black ground lead to a metal
surface of the car first.
Notes on the control and power supply leads
• The power antenna control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/AM antenna in the rear/
side glass, connect the power antenna control lead
(blue) or the accessory power input lead (red) to the
power terminal of the existing antenna booster. For
details, consult your dealer.
• A power antenna without relay box cannot be used
in). If
with this unit.
Advertisement
Related Manuals for Sony CDX-MP40
Summary of Contents for Sony CDX-MP40
- Page 1 FM/AM Compact Disc Player Installation/Connections Installation/Connexions CDX-MP40 Sony Corporation © 2003 Printed in Korea Equipment used in illustrations (not supplied) Appareils utilisés dans les illustrations (non fournis) Front speaker Haut-parleur avant Rear speaker Haut-parleur arrière Power amplifier Amplificateur de puissance...
- Page 2 BUS AUDIO IN from car antenna à partir de l’antenne de la voiture AMP REM Max. supply current 0.3 A Courant max. fourni 0,3 A Left Gauche Right Droit Left Gauche Right Droit Memory hold connection When the yellow power input lead is connected, power Précautions will always be supplied to the memory circuit even when the ignition key is turned off.
- Page 3 Orient the release key correctly. Orientez correctement la clé de déblocage. 1 8 2 5 3 m TOYOTA max. size 8 mm to dashboard/center console Dimensions au tableau de bord/console centrale max. 5 8 mm Bracket Support Existing parts supplied with your car Pièces existantes fournies avec la voiture Face the hook inwards.
- Page 4 Cet appareil ne peut pas être installé dans le chauffeur pendant la conduite. certaines voitures japonaises. Consultez, dans ce •Evitez d’installer l’appareil dans un endroit cas, votre détaillant Sony. exposé à la poussière, à la saleté, à des vibrations excessives ou à des températures Remarque Pour éviter tout dysfonctionnement, utilisez...