Table of Contents
Advertisement
Quick Links
'
*( ,QWHUORJL[
*(,QWHUORJL[FRP
Product
Summary
‚qryÃI‚Ã%'# #"
The purpose of the Quik Bridge
systems. The repeater accomplishes this by receiving and retransmitting signals from Learn
Mode™ sensors, wireless touchpads, and other repeaters. The repeater is ideal for the following
applications:
•
Installations where sensors are either beyond panel reception or cannot pass the sensor test.
•
As a substitute for preamps in installations where panel antennas are shielded by metal.
The repeater will retransmit all signals received from compatible sensors and wireless touchpads
(see "Compatibility"). It will retransmit signals received from another Euro Repeater SAW if the
DIP switches of both repeaters have been set accordingly (see "Setting the DIP Switches").
Repeater Features
Repeater features include:
•
Supervisory reports to the panel every 15 minutes.
•
A tamper switch that causes an alarm transmission if the repeater cover is removed.
•
A tamper alarm if the antenna is removed.
•
Support for a rechargeable lead acid backup battery.
•
A loop-antenna receiver, which improves reception through spatial diversity.
•
A low battery trouble report when the backup battery is low.
•
An AC power failure alarm when AC power has failed for more than 15 minutes.
•
Jam detection, which alerts the panel when the receiver detects "noise" on the same fre-
quency that the transmitters use for alarm transmissions.
Powering Options
The repeater must be hardwired into the
electrical system of the premises. Electri-
cal codes will vary depending upon the
country and city where the system is
installed. Have a qualified person connect
the 220-240VAC (50 Hz) power cable to
the power input terminal as shown in Fig-
ure 1. A minimum of 14-gauge power
wire must be used. The power wires
should not be routed near the receiver cir-
cuitry on the top of the circuit board.
Note
The repeater does not have a power switch.
A readily accessible power disconnect
device must be incorporated in the building installation wiring to comply with local safety standards.
A 12 VDC lead acid battery, such as the Panasonic LCR12V1.3P, may be installed as a backup
power source. Connect the battery to the circuit board as shown in Figure 1. The terminals of the
battery should face towards the right side of the enclosure (see Figure 2).
!
There is a risk of explosion if an incorrect type of battery is installed.
Warning
4XLN %ULGJH
®
Euro Repeater SAW is to extend the range of wireless security
T O
A C
P O W
E R
S O U R C E
T O
E A R T H
G R O U N D
Figure 1. AC Power and DC Battery Connections
Š
(XUR 5HSHDWHU
6$:
,QVWDOODWLRQ ,QVWUXFWLRQV
'RFXPHQW 1XPEHU 5HY (
T O
A C
P O W
E R
S O U R C E
T O
P O S I T I V E
B A T T E R Y
T O
T E R M I N A L
B A T T E R Y
T E R M I N A L
$SULO
N E G A T I V E
1
Advertisement
Table of Contents
Related Manuals for GE Quik Bridge 60-841-43
Summary of Contents for GE Quik Bridge 60-841-43
- Page 1 Š 4XLN %ULGJH (XUR 5HSHDWHU *( ,QWHUORJL[ ,QVWDOODWLRQ ,QVWUXFWLRQV *(,QWHUORJL[FRP 'RFXPHQW 1XPEHU 5HY ( $SULO Product ® The purpose of the Quik Bridge Euro Repeater SAW is to extend the range of wireless security systems. The repeater accomplishes this by receiving and retransmitting signals from Learn Summary Mode™...
-
Page 2: Tools And Accessories Needed
B a c k u p B a t t e r y Figure 2. Installation of Backup Battery Compatibility • All GE Interlogix Learn Mode SAW sensors and wireless touchpads at 433 mHz (non upper device type) ® •... -
Page 3: Installation Overview
Overview of DIP Switches Repeater There are 8 DIP switches (numbered 1–8 from left to right) on the repeater circuit board (see Fig- Components ure 3). DIP switch functions include: Operation • Setting the repeater identification number • Enabling (or disabling) jam detection and AC power failure reports •... -
Page 4: Setting The Dip Switches
2. Remove power from any repeaters that are already installed. 3. Perform a Dealer Sensor Test. This test checks the communication link between the control panel and the transmitters (e.g., sensors and touchpads). Refer to the panel installation manual for the Dealer Sensor Test procedure. If all of the system sensors and touchpads pass this test, a repeater is not necessary with the system. -
Page 5: Programming The Repeater Into The Panel
Note When DIP switch 8 is set to ON, the AC Failure and Jam Detection features are disabled. To use the repeater with the Euro Concord, you may set DIP switch 8 to either the OFF or ON position. Repeater No. 01 Repeater No. - Page 6 Choosing a Location for the Repeater ¾ To select a mounting location for a repeater, use the following guidelines • After a location has been selected, temporarily mount the repeater using a piece of double- sided tape or a single mounting screw (see “Mounting the Repeater”). You may need to test the transmitter and receiver in several locations before you permanently mount the repeater.
-
Page 7: Mounting The Repeater
Mounting the Repeater You must be free of static electricity before handling circuit boards. Wear a grounding strap or touch a bare metal surface to discharge static electricity. Static ¾ To disassemble and mount the repeater: 1. Remove the enclosure cover by removing the cover screws. -
Page 8: Specifications
configuring all the original repeater identification numbers). 7. Configure DIP switch 8 to match your system. 8. Power up the repeater and perform a Dealer Sensor Test (on the repeater). 9. Perform a Repeater Reception Test on all distant sensors to determine which sensor signals this repeater is able to receive and retransmit. -
Page 9: Declaration Of Conformity
Declaration of Conformity Manufacturer’s Name: GE Interlogix Manufacturer’s Address:2266 North 2nd Street North St. Paul, MN, USA 55109 EU Representative: GE Interlogix B. V. Kelvinstraat 7 6003 DH Weert The Netherlands Product Identification: Product: Quik Bridge Euro Repeater SAW Model Number: 60-841-43-EUR, 60-841-43-ITY Brand: ITI R&TTE Directive:... - Page 10 *( ,QWHUORJL[ %%ÃTrp‚qÃT‡…rr‡ÃI‚…‡uà ‹ "ÃB@ÃD‡r…y‚tv‘ÃTYWÃ8‚€€hqr…ÃTˆƒr…7ˆ†ÃhqÃRˆvxÃ7…vqtrÃh…rÃ…rtv†‡r…rqà I‚…‡uÃThv‡ÃQhˆyÃHIÃ$$ (ÃVT6 ‡…hqr€h…x†Ã‚sÃB@ÃD‡r…y‚tv‘Ã8‚p‚…qÃv†ÃhÇ…hqr€h…xÂsÃB@ÃD‡r…y‚tv‘ UrpuvphyÃTˆƒƒ‚…‡Ã'&&& % # 6yyÃ…vtu‡†Ã…r†r…‰rq Quik Bridge® Euro Repeater SAW Installation Instructions...