Ultrasonic flowmeters
energy calculator (72 pages)
Summary of Contents for Siemens CASTOMAT ION ANALOGINPUT T001
Page 1
Industrial I/O-Node - ION ANALOGINPUT T001 CASTOMAT® System Preface Scope of Delivery CASTOMAT® System Product Characteristics Industrial I/O-Node Installation and Maintenance ION ANALOGINPUT T001 6AT8000-1BA00-0XA0 Notes on the CE Mark References Appendix Manual - English Release 2008-07 Contact Information Manual - English A5E02184927 1 / 23...
Page 2
Trademarks All designations marked with ® are registered trademarks of Siemens AG. Other designations in this documentation might be trademarks which, if used by third parties for their purposes, might infringe upon the rights of the proprietors.
Industrial I/O-Node - ION ANALOGINPUT T001 CASTOMAT® System Table of Contents Preface ..............................4 Purpose of this Document......................4 Validity of this Document........................4 Audience ............................4 Standards and Approvals.......................4 Scope of Delivery ..........................5 Scope of Delivery ...........................5 Unpacking and Checking .......................5 Product Characteristics ........................6 Introduction ............................6 Hard- and Software Requirements ....................7 3.2.1...
Industrial I/O-Node - ION ANALOGINPUT T001 CASTOMAT® System Preface Purpose of this Document This document supports you when commissioning and using the device • ION ANALOGINPUT T001 of the CASTOMAT® System. Validity of this Document This document is valid for the following device: •...
Industrial I/O-Node - ION ANALOGINPUT T001 CASTOMAT® System Product Characteristics Introduction This chapter gives you an overview of the function of the component • ION ANALOGINPUT T001 of the CASTOMAT® System. The ION ANALOGINPUT T001 captures analog signals and transmits the measured data to a superior indus- trial-PC via its FireWire (IEEE1394a-standard) link with 400 Mbps.
CASTOMAT® System - User Documentation 6AT8000-5AA00-0XA0 CASTOMAT® X-Tools XP - Standard Edition 6AT8000-0AA00-1BA0 CASTOMAT® X-Tools XP - Professional Edition 6AT8000-0AA00-2BA0 Further information is obtained from your local Siemens office and from the homepage http://www.siemens.com/castomat. Manual - English A5E02184927 7 / 23...
Industrial I/O-Node - ION ANALOGINPUT T001 CASTOMAT® System Network Topology Which network topologies can be realized? The IEEE1394a technology allows the building of extended networks with up to 63 participants. With the component ION ANALOGINPUT T001, tree and chain topologies can be built. Caution The net topology is equal to the one of a bus with branching - but without loops! Tree topology...
Industrial I/O-Node - ION ANALOGINPUT T001 CASTOMAT® System Interfaces 3.5.1 Overview of Interfaces The device ION ANALOGINPUT T001 provides three plugs for further components of the CASTOMAT® System and eight inputs for analog +/-10 V signals. ION ANALOGINPUT T001 Manual - English A5E02184927 9 / 23...
Industrial I/O-Node - ION ANALOGINPUT T001 CASTOMAT® System 3.5.2 IEEE1394a Interfaces At the ION ANALOGINPUT T001 the IEEE1394a Interfaces (P1 / P2 / P3) are implemented as 6-pin-sockets. IEEE1394a Interfaces Caution Only cables of a maximum length of 4.5 m may be connected to the IEEE1394a Interfaces. Manual - English A5E02184927 10 / 23...
Industrial I/O-Node - ION ANALOGINPUT T001 CASTOMAT® System 3.5.3 Power Supply Interface The connection takes place via a 3-pin plug-in terminal block. The power supply is connected to the chassis via a low resistance in order to keep a high interference resistance. The supply voltage is attached via pin 1 (24V) and pin 2 (0V).
Industrial I/O-Node - ION ANALOGINPUT T001 CASTOMAT® System 3.5.4 Analog Interfaces At the ION ANALOGINPUT T001, the interface to the analog +/-10 V signals • CH 01 +/- … CH 08 +/- is implemented as 16-pin-socket (PHOENIX, MVSTBW 2,5/16-GF-5,08). analog interfaces Caution Only cables of a maximum length of 3.0 m may be connected to the analog inputs.
Industrial I/O-Node - ION ANALOGINPUT T001 CASTOMAT® System Indicators Name Description power indicator Color green Condition no operating voltage blinks firmware operates Name Description error indicator Color Condition no error error fan - if any Name Description indicator for the connection to the controller Color yellow Condition...
Industrial I/O-Node - ION ANALOGINPUT T001 CASTOMAT® System Technical Data Connections Power Supply Interface 24V / 0V / PD Number Connector type 3-pin plug-in terminal block, Phoenix Contact Type input Input voltage 18 ... 32 VDC Power loss at 24 VDC 24 W Current consumption at 24 VDC IEEE1394a Interface...
Page 15
Industrial I/O-Node - ION ANALOGINPUT T001 CASTOMAT® System Permitted Cable / Cable Length FireWire according to IEEE1394a standard Analog inputs maximum length: 3 m Permitted Environmental Conditions / EMC Ambient temperature during operation 0 ... +55 ° C Transportation and storage temperature -25 ...
Industrial I/O-Node - ION ANALOGINPUT T001 CASTOMAT® System Installation and Maintenance Types of Installation Note The device ION ANALOGINPUT T001 may exclusively be operated when installed on a DIN rail. Installation Installation of the device on a DIN rail: • Hang the upper table-track of the device on the DIN rail and push it down towards the DIN rail so that it snaps in.
Industrial I/O-Node - ION ANALOGINPUT T001 CASTOMAT® System Disassembly Disassembly of electric connection cables: • Disassemble the terminal block of the power supply connection cable. • Disassemble the plugs of the IEEE1394 connection cable. • Disassemble the terminal block of the analog connection cables. Removal of the device from the DIN rail: •...
Technical data subject to change. Grounding The screw on the front side of the device is provided as grounding connection. Maintenance If a fault develops, please send the device to the Siemens logistics center. Address SIEMENS AG I IA RETOUREN-CENTER FUERTH SIEMENSSTR.
Conformity Certificates The EC Declaration of Conformity is available for the responsible authorities according to the abovementioned EC Directive at the following address: SIEMENS AG I IA SE DE WUERZBURGER STR. 121 90766 FUERTH GERMANY Notes for the Manufacturers of Machines This product is not a machine in the sense of the EC Machinery Directive.
Industrial I/O-Node - ION ANALOGINPUT T001 CASTOMAT® System References Other Documentation • CASTOMAT® System - User Documentation (CD) Manual - English A5E02184927 21 / 23...
This document does not contain complete detail information to the product due to reasons of clarity and can therefore exclude each thinkable case of assembly, usage or the maintenance. Further information is obtained from your local Siemens office and from the homepage http://www.siemens.com/castomat.
Industrial I/O-Node - ION ANALOGINPUT T001 CASTOMAT® System Contact Information Address SIEMENS AG I IA SE DE WUERZBURGER STR. 121 90766 FUERTH GERMANY Manual - English A5E02184927 23 / 23...