Advertisement
Quick Links
PARTS LIST
ANTENNA
REFLECTOR
CARRIAGE BOLT
.25 X 20
(2 PLACES)
FLANGE NUT
.25-20
CARRIAGE BOLT
#10 x 1.25"
CANOPY
FEED
MODULE
TUBE
RADIO
HOSE CLAMP
(2 PLACES)
RADIO MOUNT
QTY
DESCRIPTION
BACKHAUL MODULE
with REFLECTOR (BHRF)
1
Radio Mount
1
Feed Tube
1
Antenna Reflector
1
AZ/EL Mount
1
Mast
2
Hose Clamps
2
Carriage Bolt .25 x 20
1
Hex Bolt .25-20 x 1.5"
3
Flange Nut .25-20
3
Flat Washers .25-20
1
Spacer
1
Carriage Bolt #10 x 1.25"
1
#10 Hex Nut
2
U Bolts 5/16
2
V-Bracket
4
Star Nut
1
Canopy Module Radio
FLAT WASHER
.25-20
FLANGE NUT
(3 PLACES)
.25-20
(3 PLACES)
AZ/EL MOUNT
U BOLT
MAST
(2 PLACES)
SPACER
STAR NUT
(4 PLACES)
FLAT WASHER
V-BRACKET
.25-20
(2 PLACES)
HEX BOLT
.25-20 x1.5"
#10 HEX
NUT
SUBSCRIBER MODULE
REFLECTOR (ONLY)
with REFLECTOR
(27RD)
9/04 ECN9000000 8000973-01
REFLECTOR ASSEMBLY and INSTALLATION
Tools Needed:
7/16 inch wrench or adjustable wrench
Flat blade screwdriver or 5/16 inch socket for hose clamps and ground screw
1/2 inch wrench for U-Bolts - Backhaul only
3/8" wrench for #10 nut
1
FLANGE NUT
FLAT WASHER
CARRIAGE
BOLT
REFLECTOR
Place Antenna Reflector on flat surface or table.
Attach AZ/EL Mount to Reflector using Carriage Bolts,
Flat Washers, and Flange Nuts. Tighten nuts securely.
RADIO
3
MOUNT
HOSE
RADIO
CLAMPS
Loosen and open hose clamps. Slide clamps through the two
openings in the Radio above and below the mount as shown in
this illustration. Close hose clamps attaching radio to mount.
http://www.motorola.com/canopy
Sales Support: 866-515-5825
Technical Support: 888-605-2552 (+1 217 824 9742)
27 RD REFLECTOR
2
Slide Radio into mount as shown.
RADIO
AZ/EL
MOUNT
RADIO MOUNT
4
RADIO
MOUNT
HOSE
CLAMP
Tighten Hose
Clamps securely
so the Radio is
snug to the mount
with no gaps at
the lower support
rib.
HOSE CLAMP
ADJUSTMENT
SCREW
(FACING
RADIO)
Advertisement
Summary of Contents for CANOPY 27 RD
- Page 1 Technical Support: 888-605-2552 (+1 217 824 9742) .25-20 CARRIAGE BOLT (3 PLACES) .25 X 20 REFLECTOR ASSEMBLY and INSTALLATION (2 PLACES) AZ/EL MOUNT 27 RD REFLECTOR FLANGE NUT U BOLT MAST .25-20 (2 PLACES) Tools Needed: 7/16 inch wrench or adjustable wrench...
- Page 2 To adjust azimuth, move Reflector from side to side Assemble the Feed Tube to the Reflector as while AZ/EL Clamp Hardware is loose. Once azimuth shown with 1/4" Flange Nut, .81" Spacer, is determined, tighten (2) AZ/EL Clamp Nuts securely. Flat Washer and 1-1/2"...