This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-Lenovo features or options not covered by this inspection guide.
4. Check for cracked or bulging batteries. 5. Remove the cover. 6. Check for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo alterations. 7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage.
Grounding requirements Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician. Safety notices (multilingual translations) The safety notices in this section are provided in the following languages: •...
• Check for obvious damage to a hard disk drive. If the spindle of a hard disk drive becomes noisy, the hard disk drive might have been dropped or subject to excessive force. CRU list Table 1. Models: Legion 7 16ACHg6, Lenovo Legion 7 16ACHg6, and Lenovo Legion 7 16ACHg6 1 (Machine type: 82N6) Type ac power adapter...
Chapter 4. Removing a FRU or CRU Service tools The following table lists tools for servicing Lenovo computers. Tools with a cross mark are needed for serving the product models as described by this publication. Prepare them before you service the product.
3. Follow the correct sequence in the steps for removing an FRU, as shown in the illustrations by the numbers in square callouts. 4. When removing an FRU, move it in the direction as shown by the arrow in the illustration. 5.
Pry up the latches and then remove the lower case. Figure 4. Pry up the latches and then remove the lower case Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Lower case Remove the solid-state drive (SSD) plate L Make sure the following FRU (or CRU) has been removed.
Number of screws M2 x L4.5 Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Solid-state drive (SSD) plate L Remove the solid-state drive (SSD) plate R Make sure the following FRU (or CRU) has been removed.
Figure 8. Remove the right SSD plate Screw specifications Number of screws M2 x L4.5 Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Solid-state drive (SSD) plate R Remove the solid-state drive (SSD) Make sure the following FRUs (or CRUs) have been removed.
Double-click the EXE file and follow the on-screen instructions to finish the installation. 2. X-RiteColorAssistant.exe will auto run. Click Restore Profile button from prompted window to restore the profile from Lenovo cloud. Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Solid-state drive (SSD) Remove the battery pack Make sure the following FRUs (or CRUs) have been removed.
Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Battery pack Remove the memory module Make sure the following FRU (or CRU) has been removed. “Remove the lower case” on page 28 Step 1.
Figure 14. Remove the two screws then remove the DC-in bracket Screw specifications Number of screws M2 x L6 Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: DC-in bracket Remove the Wi-Fi card Make sure the following FRUs (or CRUs) have been removed.
Figure 15. Remove the Wi-Fi card Number of screws Screw specifications M2 x L3.5 Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Wi-Fi card Remove the CMOS battery Make sure the following FRUs (or CRUs) have been removed.
Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: CMOS battery Remove the touchpad board cable Make sure the following FRUs (or CRUs) have been removed. “Remove the lower case” on page 28 “Remove the solid-state drive (SSD) plate R” on page 30 “Remove the battery pack”...
Figure 18. Remove the C cover shield mylar Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: C cover shield mylar Remove the speakers Make sure the following FRUs (CRUs) have been removed. “Remove the lower case” on page 28 “Remove the solid-state drive (SSD) plate L”...
Figure 20. Remove the speakers Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Speakers Remove the thermal module Make sure the following FRUs (or CRUs) have been removed. “Remove the lower case” on page 28 “Remove the solid-state drive (SSD) plate L”...
Step 2. Loosen six screws and then remove the thermal module. Figure 22. Loosen six screws and then remove the thermal module Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Thermal module Remove the I/O board Make sure the following FRUs (or CRUs) have been removed.
Figure 24. Remove the I/O board Screw specifications Number of screws M2 x L3.5 Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: I/O board Remove the system board and IO board cable Make sure the following FRUs (or CRUs) have been removed.
Page 47
“Remove the memory module” on page 33 “Remove the DC-in bracket” on page 34 “Remove the Wi-Fi card” on page 34 “Remove the thermal module” on page 38 Step 1. Disconnect cables connected to the system board. Figure 25. Disconnect cables connected to the system board Step 2.
Turn over the system board. Disconnect the I/O board cable from the system board and then remove the I/O board cable. Figure 27. Remove the I/O board cable Go to to look up the Lenovo part numbers of the following https://support.lenovo.com/partslookup replacement parts: System board...
Page 49
“Remove the lower case” on page 28 “Remove the thermal module” on page 38 Step 1. Peel off the adhesive tape securing the antenna boards. Figure 28. Peel off the antenna tape Step 2. Remove two screws. Figure 29. Remove two screws Screw specifications Number of screws M2 x L6...
Figure 30. Remove the strip cover Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Strip cover Remove the LCD module Make sure the following FRUs (CRUs) have been removed. “Remove the lower case” on page 28 “Remove the thermal module”...
Page 51
Figure 32. Remove two screws Screw specifications Number of screws M2 x L3 Step 3. Turn over the computer and remove four screws. Lift the LCD module slightly. Figure 33. Remove four screws and then lift the LCD module Screw specifications Number of screws M2 x L3 Step 4.
Step 2. Remove the C cover EDP conductive tape. Figure 35. Remove the C cover EDP conductive tape Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: C cover EDP conductive tape Remove the upper case Make sure the following FRUs (CRUs) have been removed.
“Remove the strip cover” on page 42 “Remove the LCD module” on page 44 “Remove the C cover EDP conductive tape” on page 46 Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Upper case Disassemble the LCD module The LCD module as a whole is not an FRU.
Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: LCD bezel Remove the hinge cover Make sure the following FRUs (CRUs) have been removed. “Remove the LCD module” on page 44 “Remove the LCD bezel” on page 47 Step 1.
Figure 38. Remove the microphone rubbers Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Microphone rubbers Remove the LCD panel Make sure the following FRUs (CRUs) have been removed. “Remove the LCD module” on page 44 “Remove the LCD bezel”...
LCD part. When the new color profiles are installed successfully, a prompted window will be displayed. Go to to look up the Lenovo part numbers of the following https://support.lenovo.com/partslookup replacement parts:...
Disconnect cables connected to the microphone board. Remove the microphone board. Figure 42. Remove the microphone board Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following replacement parts: Microphone board conductive tape Microphone board Removable tape Remove the EDP cable Make sure the following FRUs (CRUs) have been removed.
Figure 43. Remove the EDP cable Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: EDP cable Removable tape Remove the camera bracket Make sure the following FRUs (CRUs) have been removed. “Remove the LCD module” on page 44 “Remove the LCD bezel”...
Step 1. Detach the camera cable connectors and then remove the camera cable. Figure 45. Remove the camera cable Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following replacement parts: Camera cable Removable tape Remove the camera Make sure the following FRUs (CRUs) have been removed.
Figure 46. Remove the camera Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Camera Removable tape Remove the LCD cover Make sure the following FRUs (CRUs) have been removed. “Remove the LCD module” on page 44 “Remove the LCD bezel”...