Related Manuals for Danaher Motion THOMSON Electrak 10 Series
Summary of Contents for Danaher Motion THOMSON Electrak 10 Series
- Page 1 Installation & Operation Manual www.danahermotion.com Electrak 10 Series / Electromechanical Linear Actuator...
-
Page 2: Table Of Contents
OF ORIGINAL CONSUMER PURCHASE. WITH RESPECT TO be obtained by writing the Customer Service Department: COMMERCIAL AND INDUSTRIAL USES OF THE PRODUCT, THE Danaher Motion FOREGOING WARRANTY IS IN LIEU OF AND EXCLUDES ALL 1300 N. State St. OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED BY Marengo, Il. -
Page 3: Other Actuator Products
Other Actuator Products Danaher’s family of actuators offers the right load capacity, encompass a broad product range. The actuator series stroke length, and control package for almost every described on this page are available at your local Danaher application. With stroke lengths from 2 to 24 inches, load distributor or directly from the address on the back cover ratings from 25 to 1000 lbs., AC or DC models, and control of this manual. - Page 4 The Danaher family of actuator controls - a choice of separate or combined power supplies and controls to meet your various needs. MCS-2015 MCS-2025 A power supply for use with a remote control station, Combines the power supply of the MCS-2015 and the photoscanner or programmable controller to run any 24 control of the PC compatible MCS 2020 in a single VDC actuator.
-
Page 5: Application Notes
Application Notes Always make sure power is off before attempting to work on or near the actuator and its electrical controls. 2. Electrak 10 actuators are load protected with a slip clutch. The clutch will slip when the load exceeds the actuator’s rating, preventing any movement of the load. -
Page 6: Mounting
MOUNTING Danaher linear actuators are quickly and easily mounted The actuator mounting brackets must be able to by slipping pins through the holes on each end of the unit withstand the torque which is developed when the unit and into brackets on the machine frame and the load. extends or retracts. -
Page 7: Electrical Installation
ELECTRICAL INSTALLATION Wiring Danaher linear actuators should be connected in In order to use the chart, find the point of intersection of accordance with the diagram show below. the two known factors, such as amperage and distance, and read the required wire gauge from the curves on the Make sure power is off before attempting to wire chart. - Page 8 WIRING EXTERNAL LIMIT SWITCHES (OPTIONAL) Danaher actuators may also be interfaced with the MCS-2000 Series controller. Available controllers are as follows: MCS-2015 Power Supply - 110 VAC in, 24 VDC out, 17 Amp maximum. MCS-2020 Actuator Controller - Capable of extend and retract functions in a jog or continuous run model.
-
Page 9: Troubleshooting
TROUBLESHOOTING Covers D12 and D24 Models General: The chart below will be helpful for isolating malfunctions in the control system, countering difficulties with system start-up, and in troubleshooting for worn or broken mechanical or electrical components in units which have been operating for sometime. For correct diagnosis it is important to do all tests before disassembling the actuator. If the actuator is being used in conjunction with an MCS controller, see Troubleshooting Guide in controller manual for additional checkpoints. -
Page 10: Dimensions
DIMENSIONS The outline drawing shown below describes Electrak 10 ball bearing screw driven actuators. The tabulated dimension chart shows these lengths for each model and also describes the part numbers. - Page 12 Danaher Motion 1300 N. State St. Marengo, Il. 60152 Phone: 1-800-554-8466 Fax: 1-800-445-0329 E-mail: linear@danahermotion.com Literature: litrequest@danahermotion.com Or write: Danaher Motion 1300 N. State St. Marengo, Il. 60152 P-264-10 9/04 Printed in U.S.A.