Related Manuals for Pioneer X-CM66D
Summary of Contents for Pioneer X-CM66D
- Page 1 X-CM66D CD Receiver System Register your product on http://www.pioneer.eu (Europe) Operating Instructions...
-
Page 2: Table Of Contents
Thank you for buying this Pioneer product. Please read through these operating instructions so that you will know how to operate your model properly. After you have finished reading the instructions, put them in a safe place for future reference. -
Page 3: Before You Start
Before you start Chapter 1: Before you start • To prevent leakage of battery fluid, remove the What’s in the box batteries if you do not plan to use the remote control for a long period of time (1 month or more). If the fluid Please confirm that the following accessories are in the box should leak, wipe it carefully off the inside of the case, when you open it. -
Page 4: Part Names And Functions
Part names and functions Chapter 2: Part names and functions Í Remote control Switches the receiver between standby and on (page 11). Input function buttons Use to select the input source to this receiver (page 12). Use to set up or play the audio file using the Bluetooth network (page 27). - Page 5 Part names and functions 14 Volume control buttons Use to set the listening volume (page 12). Mutes/unmutes the sound (page 12). 16 DIMMER Dims or brightens the display. The brightness can be controlled in four steps (page 12).
-
Page 6: Front Panel
Part names and functions Front panel INPUT STANDBY/ON PHONES Í STANDBY/ON 10 Headphone socket Switches the receiver between standby and on (page 11). Use to connect headphones. When the headphones are connected, there is no sound output from the speakers. NFC area 11 Disc tray Touching the NFC-equipped smartphone to this area, this... -
Page 7: Speaker System
Part names and functions Attaching the Non-skid pads Speaker system Apply the accessory non-skid pads to the bottom surfaces of the speakers. Important • Use the speaker is usually in an upright position. • Take care not to jam your fingers when connecting the receiver and the speaker and putting them in place. -
Page 8: Connections
Connections Chapter 3: Connections CAUTION CAUTION • Be sure to turn off the power and unplug the power cord • These speaker terminals carry HAZARDOUS LIVE from the power outlet whenever making or changing voltage. To prevent the risk of electric shock when connections. -
Page 9: Connecting Antennas
Connections Connecting antennas Connect the Ethernet cable • Connect the DAB/FM wire antenna as shown below. Connect this unit to the network using wired LAN or Wi-Fi (wireless LAN). You can enjoy features such as TuneIn and • To improve reception and sound quality, connect Spotify by connecting to the network. -
Page 10: Plugging In
Connections Plugging in Before making or changing the connections, switch off the power and disconnect the power cord from the AC outlet. After you’ve finished making all connections, plug the unit into an AC outlet. This unit’s rear panel Power cord To AC outlet CAUTION •... -
Page 11: Getting Started
Getting started Chapter 4: Getting started To turn the power on Connecting to the network via Wi-Fi Press the Í to turn the power on. You can enjoy features such as TuneIn and Spotify by connecting to the network. After use: •... -
Page 12: Auto Setup
Getting started Auto Setup General control If the access point has an automatic connection button, you can connect without entering a password. Input function Press MENU on the remote control. When the INPUT on main unit is pressed, the current Press /... -
Page 13: Sound Controls
Getting started Sound controls Setting the wake-up timer Used to change the existing timer setting, or to set a new Equalizer timer. When the EQ is pressed, the current mode setting will be Press Í to turn the power on. displayed. -
Page 14: Calling The Wake-Up Timer
Getting started Calling the wake-up timer Using Headphones It can be used to re-use an existing timer setting. Connect to the jack plug of the headphones. As well as steps 1 through 3 in “Setting the When the headphones are connected, there is no sound wake-up timer”. -
Page 15: Disc Playback
Disc playback Chapter 5: Disc playback Play MP3 music files This system can play back a standard CD, CD-R/RW in the CD format and CD-R/RW with MP3 files, but cannot record MP3 track data is called “music file” and the location they are on them. -
Page 16: Advanced Cd Or Mp3 Disc Playback
Disc playback Basic operations Advanced CD or MP3 disc playback Function Main unit Remote Operation control Play Press in the stop mode. Stop Press in the playback mode. (when playing a CD) “RESUME” is displayed and the place where you stopped play is memorized. -
Page 17: Programmed Play (Cd)
Disc playback Programmed play (CD) Switch the display contents You can choose up to 24 selections for playback in the order Press DISPLAY during playback. you like. If the title, artist and album name has been written to the file, Whilst in the stop mode, press PGM/ that information will be displayed. -
Page 18: Using Network Functions
Creating an account on the TuneIn Radio website (tunein.com) and associating the device from My Page on Select this unit (Pioneer X-CM66). the TuneIn Radio website allows you to automatically add radio stations and programs you have followed on the The input selector of this unit website to “Favorites”... -
Page 19: Network Standby Setting
Using network functions Network Standby setting You can turn on the power of the unit via the network using an application that can control this unit. Press MENU on the remote control. Press / until “Network Standby” is displayed, then press ENTER. Press /... -
Page 20: Usb Playback
MP3 files on the front of this receiver. • When a USB storage device is not playing and the unit has • Pioneer does not guarantee that any file recorded on a not been operated for 20 minutes or more, the power will USB storage device will play or that power will be supplied automatically turn off. -
Page 21: Using The Tuner
Using the tuner Chapter 8: Using the tuner To receive an FM stereo transmission: Listening to FM Press TUNER until “FM” appears on the display. Press MENU and then press / until “FM STEREO/ The following steps show you how to tune in to FM radio MONO”... -
Page 22: Using The Radio Data System (Rds) (For European Models Only)
Using the tuner Search for stations by Program Type Note Press TUNER until “FM” appears on the display. • The backup function protects the memorised stations Press MENU and then press / until “FM RDS” for a few hours should there be a power failure or the appears on the display. - Page 23 Using the tuner Using the Auto Station program Memory Note (ASPM) • If any of the following events occur, it does not mean Whilst in the ASPM operation mode, the tuner will that the unit is faulty: automatically search for new RDS stations. Up to 30 stations - “PS”, “NO PS”...
-
Page 24: Listening To The Dab
Using the tuner Auto Scan Listening to the DAB+ You can make the auto scan again when you move the unit to other areas or add multiplex channels to the station list. Press the TUNER until “DAB” appears on the display. About DAB+ (Digital Audio Broadcasting) Press MENU and then press /... -
Page 25: Changing The Information Display
Using the tuner Changing the information display DAB Frequency table (BAND III) You can switch DAB+ display information. Press the DISPLAY button. Frequency Label Frequency Label Each time the button is pressed, the information display changes in the following order. 174.928 MHz 208.064 MHz When “NO SIGNAL”... -
Page 26: Other Connections
Other connections Chapter 9: Other connections CAUTION • Before making or changing the connections, switch off the power and disconnect the power cord from the AC outlet. • We will not accept responsibility for damage arising from the connection of equipment manufactured by other companies. -
Page 27: Bluetooth ® Audio Playback
® Bluetooth Audio playback Chapter 10: ® Bluetooth Audio playback Music playback using Bluetooth Remote control operation wireless technology The remote control supplied with this unit allows you to play and stop media, and perform other operations. Note Bluetooth wireless technology enabled device: •... -
Page 28: Listen To Music On The Unit From A Bluetooth Capable Device
Audio playback Note Starting by Bluetooth • This unit will be displayed as “Pioneer X-CM66” on all When this unit is in standby mode and operations to connect Bluetooth capable devices that you have. with this unit are made from a device with Bluetooth that has Pairing will start. -
Page 29: Pairing And Connection Using Nfc
® Bluetooth Audio playback Note Pairing and connection using NFC • Only one device can be connected at a time. NFC stands for Near Field Communication. If a NFC- • NFC can also be used to quickly cancel a Bluetooth equipped smartphone is placed close to the unit, Bluetooth connection. -
Page 30: Scope Of Operation
® Bluetooth Audio playback Scope of operation Use of this unit is limited to home use. (Transmission distances may be reduced depending on communication environment). In the following locations, poor condition or inability to receive radio waves may cause the audio to be interrupted or stopped: •... -
Page 31: Additional Information
If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work. • If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the outlet and insert again to return to normal operating conditions. - Page 32 Additional information Wi-Fi Connection Problem Remedy Cannot connect to the access point Try plugging/unplugging the power supply of wireless LAN router and the unit, check the wireless LAN router power-on status, and try reboot of the wireless LAN router. Check that the setting of SSID and encryption (WPA2, etc.) is correct.
- Page 33 Additional information Network function Problem Remedy Cannot access the Internet radio Try plugging/unplugging the power supply of this unit and the router, and try rebooting the router. Certain network service or contents available through the unit may not be accessible in case the service provider terminates its service.
- Page 34 Additional information When the Bluetooth wireless technology device is connected or operated Problem Remedy The Bluetooth wireless technology device cannot be connected or Check that no object that emits electromagnetic waves in the 2.4 operated. GHz band (microwave oven, wireless LAN device or Bluetooth Sound from the Bluetooth wireless technology device is not emitted wireless technology apparatus) is near the unit.
-
Page 35: Playable Discs And Formats
Additional information Playable discs and formats Cautions on use • Commercially available audio CDs When moving this unit Audio • CD-R/ -RW/ -ROM discs containing music When moving this unit, be sure to first check that there is no recorded in the CD-DA format disc loaded and disconnect the USB storage device. -
Page 36: About Condensation
• Do not attach pieces of paper or stickers to discs. Doing consult your nearest Pioneer authorized service center. so could warp discs, making it impossible to play them. -
Page 37: Auto Power Off Setting
Additional information Switching Wi-Fi on and off Auto power off setting Press MENU on the remote control. Press MENU on the remote control. Press / until “Network Type Set” is “Auto Power Down” will be displayed on the main display. displayed, then press ENTER. -
Page 38: Specifications
® (Wi-Fi standard) 2.4 GHz band “Pioneer” is a trademark of Pioneer Corporation, and is • Bluetooth used under license. Version ....Bluetooth Specification Ver. 4.1 The Wi-Fi CERTIFIED Logo is a certification mark of Wi-Fi ®... - Page 39 Tel :+33(0)969 368 050 Корпорация О энд Пи 2-3-12, Яэсу, Чуо-ку, г. Токио, 104-0028, ЯПОНИЯ © 2016 Onkyo & Pioneer Corporation. All rights reserved. © 2016 Onkyo & Pioneer Corporation. Tous droits de reproduction et de traduction réservés. http://www.pioneer-audiovisual.com/privacy/ SN 29402598 F1608-0...