Fujitsu FI-5530C2 Installation Procedures Manual
Windows 95\98\98se\me\2000\xp\vista
Hide thumbs
Also See for FI-5530C2:
- Operator's manual (179 pages) ,
- Getting started manual (27 pages) ,
- Getting started (11 pages)
Advertisement
Quick Links
Download this manual
See also:
Operator's Manual
Fujitsu SCSI Scanner Installation Procedures
If you are installing the following models by means of the SCSI interface then please use this
document.
Fi-5530C2
Hardware requirements.
You will need a PC system that meets our recommended specifications, an appropriate SCSI
controller, and a SCSI cable (six foot recommended maximum). For recommended PC system
specifications and SCSI controllers please reference the
You may also need your Operating System Disk.
Step A: Installing the SCSI Host Adapter (Adaptec).
1. Shut down your PC and remove the case cover.
2. Locate a free PCI slot and remove the back plate if necessary.
3. Install the SCSI controller in an open PCI slot.
Make sure that the card is seated completely in the slot and secured in the frame
Warning! Failure to secure the SCSI controller in the PC can result in damage to the
SCSI card, scanner, and/or your system.
4. Boot your PC without the scanner attached
Step B: Installing the SCSI drivers (Adaptec).
5. When the New Hardware wizard comes up, allow Windows to finish installing the
hardware files for the SCSI controller.
6. Then either install/update the ASPI drivers from the CD or go to www.adaptec.com,
and click on the "search" tab.
7. For Windows 95\98 or ME scroll down to the "Enter key word or quoted phrase" box
and type in "aspi32".
8. Next scroll down to the drivers section, click on ASPI32 and follow the prompts to
download it your desktop or a new folder.
9. Afterwards go to that location and double click on the "aspi32.exe" icon and follow
the prompts.
10. When the message "ASPI is up to date" appears, reboot and go to the next step.
11. For Windows 2000 or XP scroll down to the "Enter key word or quoted phrase" box
and type in "aspi".
12. Next scroll down to the drivers section, click on ASPI_v470 or higher and follow the
prompts to download it.
13. Afterwards go to that folder and unzip the file to the default Adaptec\ASPI folder.
14. Then go to start, run, browse to the Adaptec\ASPI folder, select ASPIINST.EXE and
run it.
15. When the message "ASPI is up to date" appears, reboot and go to the next step.
Rev082708A
Windows 95\98\98SE\ME\2000\XP\Vista
Fi-6140
Fi-6240
Fi-6670\A
Fi-6770\A
Scanner Hardware Reference
.
page.
Page 1 of 1
Advertisement
Related Manuals for Fujitsu FI-5530C2
Summary of Contents for Fujitsu FI-5530C2
- Page 1 Fujitsu SCSI Scanner Installation Procedures Windows 95\98\98SE\ME\2000\XP\Vista If you are installing the following models by means of the SCSI interface then please use this document. Fi-5530C2 Fi-6140 Fi-6240 Hardware requirements. You will need a PC system that meets our recommended specifications, an appropriate SCSI controller, and a SCSI cable (six foot recommended maximum).
- Page 2 Windows 95\98\98SE\ME\2000\XP\Vista Step C: Installing the drivers from the Setup CD. To begin it is recommended that you install the drivers first before connecting the scanner. Installing the STI-Twain driver. 1. Insert the Scanner Setup CD into your CD Rom.
- Page 3 WinZip* self-extractor box will popup. Click on browse and select the Fujitsu Downloads folder, then click on Extract. The file will begin to unzip and when finished a message box will report the number of files unzipped. Click on OK and close WinZip.
- Page 4 SCSI host adapter. Next if the scanner is the last device (only device) on the SCSI chain then it must be terminated. If the scanner is not the last device on the SCSI chain, then the terminator should be removed or turned off before connecting it to the next SCSI device.
- Page 5 2. After the Untitled Screen has open, click Scan on the Menu bar and go down to zone three, then click Select Scanner. 3. Select the Fujitsu Twain source for your scanner by highlighting it and clicking OK. You will only need to do this once unless you are scanning with multiple sources.
- Page 6 Congratulations! You have successfully completed and tested your scanner installation. Step H: Installing third party software applications. After you have successfully installed all the Fujitsu software and hardware, then it is time to install any additional third party scanning software that you wish to use. Please follow the software manufacturer’s instructions for installation.