Page 1
Internal Use Only North/Latin America http://aic.lgservice.com Europe/Africa http://eic.lgservice.com Asia/Oceania http://biz.lgservice.com PLASMA TV SERVICE MANUAL CHASSIS : PB01A MODEL : 50PK550 50PK550-SA CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. Printed in Korea P/NO : MFL63141001(1005-REV00)
Page 8
- Operate DDC write S/W (EDID write & read) - It will operate in the DOS mode. < For write EDID data, setting Jig and another instruments > - EDID data (Model name = LG TV) - 2010 EDID DATA CHECK SUM. BLOCK(0)
Page 29
Great Company Great People Brazil BBTV Training manual Brazil BBTV Training manual Contents - Block Diagram - System Design - Trouble Shooting Guide ATSC Group Brazil Team Last updated 2009.11.14...
Page 30
Power-Up Sequence BCM3556 (Main Chip) There are no power sequence requirements. Any sequence will be acceptable All supplies have a minimum ramp up time of 100us. There is no maximum ramp up time restriction RESET should be held active during ramp up and at least 10ms after all voltages are above 95% of their specified nominal levels Min 100us All power rails above...
Page 33
10년 GP2 BR Chassis ramp up time = ALL OK 10년 GP2 BR Chassis ramp up time : check!! D1.2V = 14ms D1.8V = 3.28ms A2.5V = 376㎲ D3.3V = 1.76ms Customer Oriented R&D Breakthrough...
Page 34
10년 GP2 BR PDP Audio amp reset spec On power up, reset be held low = 222ms > 100㎲ Customer Oriented R&D Breakthrough...
Page 42
Trouble Shooting Guide for LG Service Man Please check system, after power Off/On one time Power-Up Boot Fail Trouble Shooting No OSD Trouble Shooting Digital TV Video Trouble Shooting Analog TV Video Trouble Shooting Component Video Trouble Shooting RGB Video Trouble Shooting...
Page 43
1. Power-Up Boot Fail Trouble Shooting Check P500 All Voltage Level Check Power connector Replace Power board (17V, 5V, 3.3V, 5V_ST) Check All Voltage Level Replace one of Bead at Bead & Recheck Replace one of IC504IC500/ L502 / Check Voltage Level 3.3V at L514 L514 &...
Page 45
2. No OSD Trouble Shooting Check P500 5V_ON Check GPIO Path of Micom Check P202 DISP_EN Check 5V Voltage Level Check Power connector Replace Power board at P500 Check 5V Voltage Level Replace one of L501 at L501 & Recheck Check all multi voltage Check power up boot sequence (1.2v, 3.3v, 1.8v)
Page 46
No OSD Trouble Shooting (Module Power Sequence) Customer Oriented R&D Breakthrough...
Page 47
Module Control Trouble Shooting “TILT” on Adjust Remocon Check SMPS & cable PDP Module Power is OK? : PDP internal pattern displays? Replace PDP Module PDP Module is OK. Check Signal Check P202 SCL,SDA line SCL,SDA Replace X1 : X1 output line R244, R252 <...
Page 49
3. Digital TV Video Trouble Shooting Check RF Cable Check Tuner(TU600) Power Replace one of Bead (5.0V, 3.3V, 1.2V) & Recheck Check IF Signal pin #17, 18 Maybe Tuner has problems Check Demodulator Power Replace L604 / IC601 (3.3V, 1.2V) L604, IC601 Check Demodulator X-TAL Replace X-TAL (X600)
Page 51
4. Analog TV Video Trouble Shooting Check RF Cable Replace one of Check Tuner Power L601/L600/L602 (5.0V, 3.3V, 1.2V) & Recheck Check CVBS Signal Maybe Tuner(TU600) has problems TU600 #11 Pin Replace one of Check CVBS Signal C328/R308/Q602/R621 C328 & Recheck Maybe BCM3556(IC100) has problems Customer Oriented R&D...
Page 53
5. Component Video Trouble Shooting Check Signal Format Is it supported signal? Check Component Cable Check Component Jack1001 Replace Jack Replace one of Check Component Signal L1005/L1004/L1003/L1000/L1001 L1005/L1004/L1003/L1000/L1001 L1002 L1002 & Recheck Check Component Signal Replace it C317/C318/C319/C320/C321/C322 Maybe BCM3556(IC100) has problems Customer Oriented R&D Breakthrough...
Page 55
6. RGB Video Trouble Shooting Check Signal Format Is it supported signal? Check RGB Cable Check RGB Jack JK901 Replace Jack Check RGB Signal Replace It & Recheck R912, R911, R910 Check Sync Signal Replace one of R900/R901/IC900 IC900 #11, #3 &...
Page 57
7. AV Video Trouble Shooting Check Signal Format Is it supported signal? Check AV Cable Check Jack JK1001/JK1000 Replace Jack Replace one of Check CVBS Signal R1005/R1004 R1005/R1004 & Recheck Replace one of Check CVBS Signal C329/C330/R307/R309/R316/R321 C329/C330/R307/R309/R316/R321 & Recheck Maybe BCM3556(IC100) has problems Customer Oriented R&D...
Page 59
8. HDMI Video Trouble Shooting Check Signal Format Is it supported signal? Check HDMI Cable Check HDMI Jack Replace Jack JK802, JK803, JK801, JK800 Check HDMI S/W Power(1.8V, 3.3V) Replace one of L800/L801 @ L800, L801 & Recheck Re-download EDID data Replace IC800 Maybe BCM3556(IC100) has problems...
Page 61
9. All Source Audio Trouble Shooting Make sure you can’t hear any audio Replace Speaker Check Speaker Check Connector P700 Replace Connector Replace one of Maybe TAS5709 has problems. Check Signal Capacitor, Register L700, L701 Replace It & Recheck Check IC700 Power 17V, 3.3V Replace It &...
Page 63
10. Digital TV Audio Trouble Shooting Follow procedure digital TV video Check video output trouble shooting Follow procedure All source audio Maybe BCM3556 internal audio DSP trouble shooting has problems. Replace It Customer Oriented R&D Breakthrough...
Page 65
11. Analog TV Audio Trouble Shooting Follow procedure analog TV video Check video output trouble shooting Check Tuner Power Replace one of L601/L600/L602 (5.0V, 3.3V, 1.2V) & Recheck Check SIF Signal Maybe Tuner(TU600) has problems TU600 #9 Pin Replace one of Check SIF Signal R315/C308/Q603/C616/R622 C308...
Page 71
14. USB Trouble Shooting Check USB 2.0 Cable Check USB device If device is 2.5 inch HDD, Check power adaptor Check USB HUB X-TAL Replace X-TAL(X1100) Check USB Input voltage(D3.3V) Check input voltage Check 5V voltage level at Replace one of analog switch(IC1102, IC1101) IC1102, IC1101 &...
Page 73
15. Digital TV Recording Fail Trouble Shooting Follow procedure digital TV Check video/audio output video/audio trouble shooting Check HDD Replace HDD Check USB block Use USB Trouble shooting guide Maybe IC1100 has problems Maybe BCM3556(IC100) USB block Replace It (Only PK950) has problems.