Electrolux W455H Installation Manual
Hide thumbs
Also See for W455H:
- User manual (20 pages) ,
- Operating manual (24 pages) ,
- Operating manual (28 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Electrolux W455H
Summary of Contents for Electrolux W455H
- Page 1 Installation manual W455H 438 9067-51/EN 06.35...
-
Page 3: Table Of Contents
Contents Contents Technical data ....................3 Installation ....................7 Siting......................7 Unpacking ....................8 Mechanical installation ................9 Water supply ..................10 Drain ...................... 11 Electrical installation ................12 Machine connection options ..............13 Connection of external liquid supplies ..........14 Marine installation ................. -
Page 5: Technical Data
Technical data Technical data W455H Innerdrum, volume litres diameter depth Drum speed wash 5/54 extraction 100 Heating electricity steam – hot water G-factor Weight, net Connections Water valves connection DN20 /4’’ Capacity at 00 kPa l/min Drain valve outer Ø mm... - Page 6 Technical data Control panel Soap box Door opening ø255 Cold water Hot water Drain, valve Drain, pump Electrical connection 850/875* * Adjustable height, 25 mm 6206...
- Page 7 Technical data Frequency of the dynamic force Max floor load at extraction 1.2±0. Sound levels Solid sound level in dB (A) re 10 mm/sec (44-707 Hz) Airborne sound level dB (A) re 2x10 51/71* 45/59* Vibration level (m/sec 0.6 0.66 Vibration speed (mm/sec) A = Standard...
-
Page 9: Installation
Installation Installation Leave the machine on the pallet on which it was delivered until the installation site has been pre- pared to receive it. Rec. 500 mm Siting Install the machine close to a floor drain or open waste water channel. Rec. -
Page 10: Unpacking
Installation Unpacking In transit the machine’s drum is locked in place by three locking devices between chassis and drum. Instructions for installing machine and removing transit locking devices, step by step: • Remove the packaging. • Remove the components shipped inside the drum. -
Page 11: Mechanical Installation
Installation Mechanical installation • Mark and drill 2 holes (ø 8 mm) about 40 mm deep in the positions shown. = position of feet = drilling points for expander bolts • The machine shall be lifted in the bottom frame. Front •... -
Page 12: Water Supply
Installation Water supply Each water supply line to the machine should be fitted with a manual shut-off valve and debris filter to facilitate servicing. Check the local regu- lations to determine whether non-return valves are required. Connection hoses should be of the quality re- quired according to regulations in the country of use. -
Page 13: Drain
Installation Drain Direct discharge Attach the drain hose to the machine’s drain out- let and install so it empties (min 25 mm) above the floor drain or waste water channel. Pump drain Position the highest part of the drain hose 650±50 mm above the lowest part of the mach- ine. -
Page 14: Electrical Installation
Installation Electrical installation Electrical installation must be carried out by an authorised electrician. • Install a multi-pole switch for the machine’s electrical supply. • Connect the machine’s cable to the switch. • Check that the earth has been connected in the correct way. Fuse ratings are given in the table. -
Page 15: Machine Connection Options
Installation Machine connection options Switchover or reconnection of the machine may only be performed by qualified, autho- rised personnel. This machine can be switched/reconnected fol- lowing the options set out below. 2065 A The machine cannot be switched from 50 Hz to 60 Hz or vice versa. N/L 02 Reconnection/switchover of this type can- not be performed on machines fitted with a... -
Page 16: Connection Of External Liquid Supplies
Installation Connection of external liquid 1 = N supplies 2 = L 4 = Ground Machines fitted with connectors • Connect the pump equipment to connections A and B on the washing machine. Connect the signal cable to B and the power supply to A. - Page 17 Installation Outputs • Connect external power supply (e.g. 24V DC) for pumps to 9 and 10. If an internal power supply (from the washing machine) is being used, it can be taken from 1 (N) and connec- ted to 9 and from 2 (L) and connected to 10. Max load on the outputs 0.5 A.
- Page 18 Installation • Connection 8 can be connected if the washing program is to pause, e.g. while washing detergent is being dosed. Dosing system Pause signal 24V DC 6266 Detergent tank Empty 20V 6265 • Connection 7. If this is connected, an error message will be displayed if any of the chemi- cal tanks are empty.
- Page 19 Installation Functions for I/O -cards • Check the electrical schematic for the machine to find out what functions are available for the machine. The electrical schematic can have one of the following: 22E, 22B, 22C or 22D. Type of I/O card Address Function I/O:s Inp opt...
- Page 20 Installation Type of I/O card Address Function I/O:s P out Inp opt V in Out 5NO Out CO Central payment Start 230 Program run 1 Central payment Supply 0 Common 24V Program run 1 Start 24 Supply 24 616...
- Page 21 Installation Type of I/O card Address Function I/O:s P out Inp opt V in Out 5NO Out CO Central payment Coges Machine free 1 Start permitted Central payment EBS, Camping Start permitted 61...
- Page 22 Installation Type of I/O card Address Function I/O:s P out Inp opt V in Out 5NO Out CO "Time of day discount" "Time of day discount" 100-240VAC "Time of day discount" 24V AC/DC 614...
-
Page 23: Marine Installation
Installation Marine installation This machine can be installed in marine installa- tion. The maximum value for rolling is ± 15° and for stamping ±8°. ���� • The machine shall be placed as shown in fig. • Mark the two holes (A) on the floor plate on the site of machine installation. - Page 24 Installation • Thread up the four feet of the machine as much as possible. Place the machine at its site. Place the spacers (B) between machine and floor. • Tighten the machine to the floor with the two bolts. • Adjust the feet of the machine to the floor and lock them with the nuts.
-
Page 25: Function Checks
Function checks Function checks Perform the following checks once the machine is installed: • Open the manual water valves. • Turn on the power to the machine. • Put detergent into compartment 2 (Main wash). • Select a 60° program with the control knob (1). - Page 28 Share more of our thinking at www.electrolux.com...