Related Manuals for HP Compaq CV5500
Summary of Contents for HP Compaq CV5500
-
Page 1: Reference Guide
Reference Guide Color Monitor Series 5500, 7500, 7550, 9500 Document Part Number: 326689-002 May 2003... - Page 2 The warranties for HP products are set forth in the express limited warranty statements accompanying such products. Nothing herein should be construed as constituting an additional warranty.
-
Page 3: Table Of Contents
On-Screen Display Functions ....4–4 Monitor Messages ......4–8 No Signal Message . - Page 4 B Technical Specifications 5500/15” Series Monitor ......B–1 7500/17” Series Monitor ......B–3 7550/17”...
-
Page 5: Introduction
Your microprocessor-based, digitally controlled color monitor is a high-performance and easy-to-use product. It employs the latest on-screen menu technology. Kit Contents The monitor kit contains: ■ CRT monitor ■ Monitor Base (preinstalled on select models) ■ AC power cord (select models) ■... -
Page 6: Safety And Maintenance Guidelines
When you need to disconnect the power to the equipment, unplug the power cord from the power outlet by grasping the plug firmly. Never pull on the cord. Reference Guide www.hp.com Guidelines 2–1... -
Page 7: Maintenance Guidelines
Safety and Maintenance Guidelines Ä CAUTION: For the protection of your monitor, as well as your computer, connect all power cords for your computer and its peripheral devices (such as a monitor, printer, scanner) to some form of surge protection device such as a power strip or Uninterruptible Power Supply (UPS). - Page 8 These openings must not be blocked or covered. Never push objects of any kind into cabinet slots or other openings. ■ Do not place plants on top of your monitor. Water or dirt from the plant may get into the vents. ■...
-
Page 9: Removing The Monitor Base
■ Do not place the monitor face down. Damage could result to the front panel controls or the monitor screen. Removing the Monitor Base In the event that you need to disassemble the base from the monitor, follow these instructions: 1. -
Page 10: Installation
Monitor Base Installation On some monitors, the base must be attached prior to monitor installation. If you need to attach the base, follow these steps: 1. Align the hooks on the base with the sockets on the bottom of the monitor and attach the base. -
Page 11: Monitor Installation
Installation 2. Push the base toward the front of the monitor until it stops. Monitor Installation Before installing your monitor, place it in a convenient, well-ventilated location near your computer. 1. Turn off the power to your computer and other peripheral devices. - Page 12 4. Power on your computer and monitor. ✎ If your monitor fails to function properly, refer to “Troubleshooting.” 5. If necessary, adjust the front panel monitor controls according to your personal preference. See “Front Panel Controls” for detailed information. Your monitor installation is now complete.
-
Page 13: Operation
Information Files The CD-ROM included with this monitor contains two data files that must be installed onto your computer: an .INF file and an .ICM file. The .INF file designates software and defines monitor resources used by Microsoft Windows to ensure monitor compatibility with the graphics adapter in your computer. -
Page 14: Front Panel Controls
Moves backward through menu options or decreases adjustment levels. Right Adjustment Moves forward through menu options or increases adjustment levels. Power/LED Controls power to the monitor. The LED on the power button indicates the state of the monitor. www.hp.com Function Reference Guide... -
Page 15: On-Screen Display
The On-Screen Display (OSD) adjusts the screen image based on your viewing preferences. To access the OSD, do the following: 1. If the monitor is not already on, press the Power button to turn on the monitor. 2. Press the Select button to display the On-Screen Display menu. -
Page 16: On-Screen Display Functions
Operation 4. Press the Select button on the monitor choose the function. 5. The adjustment window displays. Press the Right-Adjustment or Left-Adjustment buttons to increase (Right) or decrease (Left) the level of adjustment. 6. Press Select to save the new adjustment. - Page 17 Right-Adjustment moves the top and bottom of the image to the right and Left-Adjustment moves the top and bottom of the image to the left. www.hp.com Operation 7500 & 5500 7550 9500 4–5...
- Page 18 Moire correction and Left-Adjustment decreases the Moire correction. This control demagnetizes the screen to reduce color impurities. Hewlett-Packard suggests you not degauss more than once within a 30-minute period of time. www.hp.com 7500 & 5500 7550 9500 Reference Guide...
- Page 19 Right-Adjustment selects the color temperature to the right and Left-Adjustment selects the color temperature to the left. This control resets the monitor to factory default values. This control exits the OSD menu. www.hp.com Operation 7500 & 5500 7550 9500 4–7...
-
Page 20: Monitor Messages
Operation Monitor Messages No Signal Message If a No Signal message displays on your monitor, check to be sure your video cable is properly connected and ensure that your computer is powered on. 4–8 www.hp.com Reference Guide... -
Page 21: Out Of Frequency Range Message
Out of Frequency Range Message If an Out of Frequency Range message displays on your monitor, your video resolution and/or refresh rate are set higher than the levels your monitor supports. To change the video resolution or refresh rate on your monitor, follow these steps: 1. -
Page 22: Using The Energy Saver Mode
Operation Using the Energy Saver Mode Your monitor is designed to meet strict Environmental Protection Agency (EPA) Energy Star requirements for reduced power consumption. Using a combination of hardware and software functions, this energy-saving feature allows your computer to control your monitor’s power consumption and reduce your monitor’s power state when not in use. - Page 23 < 5 watts ✎ Your monitor’s energy saver feature works only when your monitor is connected to a computer that also has energy saver features. The Energy Saver utility, with its energy saving features, is available with all Microsoft Windows operating systems. Some features are also available in DOS.
-
Page 24: Solving Common Problems
Video cable is improperly connected. Screen blanking utility is active. Brightness and contrast are too low. A magnetic object may be nearby. www.hp.com Solution Connect the power cord. Turn on power. Connect video cable properly. Depress any key on the keyboard or move the mouse. - Page 25 Horizontal width may need adjustment. Vertical height may need adjustment. Horizontal position may need adjustment. Vertical position may need adjustment. www.hp.com Solution Press the SELECT button to access the On-Screen Display. Select Degauss to activate. Hewlett-Packard suggests you not...
- Page 26 Video resolution and/or refresh rate are set higher than what your monitor supports. There is not enough air space to allow proper ventilation. www.hp.com Troubleshooting Solution Connect the 15-pin monitor video cable to the computer. Be sure that the...
-
Page 27: Using The Worldwide Web
Using the Worldwide Web Before contacting customer services, refer to the support Web site at: http://www.hp.com/go/support. Preparing to Call Technical Support If you cannot solve a problem using the troubleshooting tips in this section, you may need to call technical support. Have the following information available when you call: ■... -
Page 28: B Technical Specifications
30 to 54 KHz 50 to 120 Hz 70 MHz Max. Video RGB Analog Sync. TTL Separate 15-pin D-sub connector 100 to 240V AC 50 +3 to 60 +3 Hz 30 amps @ 120V 60 amps @ 220V www.hp.com B–1... - Page 29 365 x 400 x 418 mm (maximum) 29 lb Max. 13 kg Max. F to 95 C to 35 F to 140 C to 60 20% to 80% (non-condensing) Up to 10,000 ft./3048 meters Some models meet TCO’99 Some models meet MPRII www.hp.com Reference Guide...
-
Page 30: 7500/17" Series Monitor
15-pin D-sub connector 100 to 240V AC 50 +3 to 60 +3 Hz 30 amps @ 120V 60 amps @ 220V 100 W (Max.) 16.6 x 17 x 17.5 inches (maximum) 410 x 432 x 445 mm (maximum) www.hp.com Technical Specifications B–3... - Page 31 Plug and Play B–4 38 lb Max. 17 kg Max. F to 95 C to 35 F to 140 C to 60 20% to 80% (non-condensing) Up to 10,000 ft./3048 meters Some models meet TCO’99 Some models meet MPRII www.hp.com Reference Guide...
-
Page 32: 7550/17" Flat Crt Monitor
15-pin D-sub connector 100 to 240V AC 50 +3 to 60 +3 Hz 30 amps @ 120V 60 amps @ 220V 100 W (Max.) 16.1 x 17 x 17.4 inches (maximum) 410 x 432 x 442 mm (maximum) www.hp.com Technical Specifications B–5... - Page 33 Plug and Play B–6 42 lb Max. 19 kg Max. F to 95 C to 35 F to 140 C to 60 20% to 80% (non-condensing) Up to 10,000 ft./3048 meters Some models meet TCO’99 Some models meet MPRII www.hp.com Reference Guide...
-
Page 34: 9500/19" Series Monitor
50 to 160 Hz 210 MHz Max. Video RGB Analog Sync. TTL Separate 15-pin D-sub connector 100 to 240V AC 50 +3 to 60 +3 Hz 30 amps @ 120V 60 amps @ 220V 130 W (Max.) www.hp.com Technical Specifications B–7... - Page 35 455 x 470 x 475 mm (maximum) 44 lb Max. 20 kg Max. F to 95 C to 35 F to 140 C to 60 20% to 80% (non-condensing) Up to 10,000 ft./3048 meters Some models meet TCO’99 Some models meet MPRII www.hp.com Reference Guide...
-
Page 36: C Agency Regulatory Notices
Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. -
Page 37: Cables
Agency Regulatory Notices Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain compliance with FCC Rules and Regulations. Declaration of Conformity for Products Marked with FCC Logo, United States Only This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause... -
Page 38: Canadian Notice
Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Avis Canadien Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. European Notice Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. -
Page 39: Korean Notice
100-120V or 200-240V. The power cord set (flexible cord or wall plug) received with the monitor meets the requirements for use in the country where you purchased the equipment. If you need to obtain a power cord for a different country, you should purchase a power cord that is approved for use in that country. - Page 40 18AWG, and the length of the cord must be between 6 feet (1.8 m) and 12 feet (3.6 m). If you have questions about the type of power cord to use, contact your HP authorized service provider. A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it.
-
Page 41: D Tco'99 Requirements
TCO‘99 Requirements You have just purchased a TCO'99 approved and labelled product. Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. - Page 42 TCO‘99 Requirements There are also other characteristics of a computer, such as energy consumption levels, that are important from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of electricity generation have a negative effect on the environment (for example, acidic and climate-influencing emissions, radioactive waste), it is vital to save energy.
-
Page 43: Environmental Requirements
Labelled products must meet strict environmental demands, for example, in respect of the reduction of electric and magnetic fields, physical and visual ergonomics and good usability. Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development SE-114 94 Stockholm, Sweden... -
Page 44: Cadmium
TCO‘99 Requirements The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit boards since no substitutes are available. ✎... -
Page 45: Cfcs (Freons
✎ Mercury is a heavy metal that is Bioaccumulative. CFCs (Freons) The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards.