Advertisement
Quick Links
SIMATIC
S5-135U/155U
System Manual
This manual has the
order number:
6ES5998-0SH21
11/99
Edition 07
Contents
Notes on Using this Manual
and on the CE Symbol
Centralized and Distributed
Configuration of a
Programmable Controller
Installation Guidelines
Central Controllers and
Expansion Units
Power Supply Units
CPUs, Memory Cards,
Memory Submodules,
Interface Submodules
Multiprocessor Operation/
Coordinators
Interface Modules
Digital Input/Output Modules
Analog Input/Output Modules
Monitoring Module
Connector Assignments
Appendices
Appendix
Guidelines for Handling
Electrostatically-Sensitive
Devices (ESD)
Index
1
2
3
4
5
6
7
8
9
10
11
A
B
Advertisement
Related Manuals for Siemens SIMATIC S5-135U
Summary of Contents for Siemens SIMATIC S5-135U
- Page 1 Contents Notes on Using this Manual and on the CE Symbol Centralized and Distributed Configuration of a Programmable Controller SIMATIC Installation Guidelines Central Controllers and S5-135U/155U Expansion Units Power Supply Units CPUs, Memory Cards, Memory Submodules, Interface Submodules System Manual Multiprocessor Operation/ Coordinators This manual has the...
- Page 2 Caution Warning Trademarks Copyright Siemens AG 1993 All rights reserved Disclaimer of Liability The reproduction, transmission or use of this document or its We have checked the contents of this manual for agreement with the contents is not permitted without express written authority.
- Page 3 Contents Notes on Using this Manual and on the CE Symbol ..... . . Notes on Using this Manual ........Notes on the CE Symbol .
- Page 4 Contents 3.6.1 Interference-Free Connection of a Monitor to the CP of the S5 Controller ........... 3-30 3.6.2 Shielding and Grounding...
- Page 5 Contents CPUs, Memory Cards, Memory Submodules, Interface Submodules ..CPU 948B -3UA13 or CPU 948B -3UA23 ......5.1.1 Technical Description .
- Page 6 Contents 5.11.3 V.24 Submodule ..........5-99 5.11.4 TTY Submodule...
- Page 7 Contents Common Technical Specifications ....... . . 8-28 Specification Sheets for the Modules .
- Page 8 Contents The 465 Analog Input Module ........9-50 9.5.1 Design...
- Page 9 Contents 10.3.1 Addressing ........... . . 10-10 10.3.2 Setting the Address Switches S1, S2, S3, S4...
- Page 10 Contents System Manual C79000-G8576-C199-07...
- Page 11 Notes on Using this Manual and on the CE Symbol Notes on Using this Manual The S5-135U/155U PLC is a member of the family of SIMATIC S5 programmable (logic) controllers. The controller can be used in single and in multiprocessor operation with up to four CPUs. In multiprocessor operation, each CPU processes its individual user program independently of the other CPUs (multicomputing).
- Page 12 Notes on Using this Manual and on the CE Symbol How the Manual is Pointers on how this manual is organized are given as a guide below. They Organized will assist you when using your S5-135U/155U programmable controller. At the start of this manual you will find the “Safety-Related Guidelines” and the “ESD Guidelines.”...
- Page 13 Notes on Using this Manual and on the CE Symbol Chapter 11 lists the connector assignments of the individual modules and subracks. The Appendix contains the ordering data for the products described in this manual, references to further reading material and the index of keywords in this manual.
-
Page 14: Notes On The Ce Symbol
SIMATIC S5 devices. Guidelines Moreover, the following rules must be observed when using certain modules. Installing the Programmable controllers of the type SIMATIC S5-135U/S5-155U must be Devices installed in metal cabinets according to these installation guidelines. Working on... - Page 15 Notes on Using this Manual and on the CE Symbol Notes on Additional measures are required when using the following modules. Individual Modules A shielded signal cable is required for the following modules: Order Number Module 6ES5 453-4UA12 Digital output module 453-4 6ES5 457-4UA12 Digital output module 457-4 A filter (SIFI C B841213-C-B30 or equivalent) is required in the 230 V AC load voltage supply...
-
Page 16: Notes For Machine Manufacturers
Notes on Using this Manual and on the CE Symbol Notes for Machine Manufacturers Introduction The SIMATIC programmable controller is not a machine in the sense of the EC Directive on machines. Therefore, there is no declaration of conformity for SIMATIC as regards the EC Directive 89/392/EEC on machines. EC Directive The EC Directive 89/392/EEC on machines controls machine requirements. - Page 17 SIMATIC-compatible modules have any quality assurance at all or one that is nearly equivalent to ours. These so-called SIMATIC-compatible modules are not marketed in agreement with Siemens; we have never recommended the use of so-called SIMATIC-compatible modules of other manufacture. The...
- Page 18 Notes on Using this Manual and on the CE Symbol System Manual C79000-G8576-C199-07...
-
Page 19: Centralized And Distributed Configuration Of A Programmable Controller
Centralized and Distributed Configuration of a Programmable Controller This chapter contains an overview of the methods of configuring an S5-135U/155U PLC. You will find a description of the types of communication between a central controller and the expansion units, and an overview of the interface modules required for the different types of communication. - Page 20 Centralized and Distributed Configuration of a Programmable Controller Application The S5-135U/155U programmable controllers comprise a central controller (CC) and, if required, one or more expansion units (EUs). You need EUs when there are insufficient slots in the CC for the modules to be used. Various interface modules (IMs) are available for communication between the CC and the EUs and between the EUs.