Table of Contents
Advertisement
CA-MX55MBK
|
Using the Tuner
Listening the Broadcasts
The tuner can receive FM and AM broadcasts. Stations can be tuned in
manually, automatically, or from preset memory storage.
Manual Tuning
1. Select the broadcast band you want to tune in by pressing the FM
of AM button on the Tuner.
FM
aM
Oo
Oo
2. Press the TUNING/TIMER/DIMMER
button ( < or > ) to tune In a
station.
TUNING/TIMER/DIMMER:
3. Hold down the TUNING/TIMER/DIMMER button to change the
frequency rapidly, then tap the button to set the frequency precisely.
Automatic Tuning
1. Select the broadcast band you want to tune In by pressing the FM
or AM button on the Tuner.
2. Hold down the TUNING/TIMER/DIMMER
button (< orp) for a
moment, and then release the button.
*
When a station is tuned in, the TUNED indicator lights up.
Note:
*
The Tuner will tune in the nearest strong station.
Presetting Stations in Memory
You can store up to 40 of your favorite radio stations (FM and AM) in
memory, giving you quick, easy access to the stations.
1. Selecta band by pressing either the FM or AM button on the Tuner.
2. Press the TUNING/TIMER/DIMMER button ( < or
) to tune ina
station.
-
3. Press the MEMORY button on the Tuner.
The "MEMORY' indicator on the Tuner display blinks for 5 seconds.
4. Press the PRESET button( < or > )onthe Tunertoassignanumber
(1-40) to the station, or enter a number (1-40) with the Remote
Controller's numeric keypad.
PRESET
PRESET
<
>
Example:
To enter 7, press 7
To enter 17, press "+10",
then "7".
To enter 20, press "+10",
then "10"
*
Before using the numeric keypad, press the TUNER button.
This will allow you to use the numeric keypad in the Tuner mode.
*
Ifthe "MEMORY?" indicator has stopped blinking, press the MEMORY
button again and repeat step 4.
+
Ifthe preset number you chose already has a station assigned to it, the
old station will be replaced by the new one.
20
22 (No. 20342)
5. Press the MEMORY button again.
This stores that station in memory, with the preset number (1-40) you
chose in step 4.
6. Repeat steps 1-5 for each station you want to storein memory with
a preset number.
Caution! !f the system is unplugged or if a power failure occurs, the preset
stations stored in memory may be lost.
Cancelling Preset Stations
1. Press the CANCEL button on the Tuner.
The "CANCEL" light on the Tuner display blinks for 5 seconds.
CANCEL,
2. Press the PRESET button (< or >) on the Tuner to select the
preset station you want to cancel.
if the "CANCEL" light has stopped biinking, press the CANCEL button
again and repeat step 2.
3. Press the CANCEL button again.
The preset station will be cancelled.
Tuning in Preset Stations
¢
Press the PRESET button ( ¢ or > ) on the Tuner to select the preset
station you want. The preset station numbers are displayed sequentially
each time you press the PRESET button.
*
You can also select a station by entering its preset number on the
Remote Controller's numeric keypad.
*
Before using the numeric keypad, press the TUNER button.
This will allow you to use the numeric keypad in the Tuner mode. .
FM Reception Modes
There are two FM reception modes: AUTO and MONO.
AUTO:
Stations are tuned in with either STEREO or MONO, de-
pending on the FM signal.
MONO:
Stations are tuned in with MONO
only. This will reduce
interference noise of weak stations and make the reception
sound better.
1. Press the FM MODE/ MUTE button on the Tuner to switch between
the AUTO and MONO reception modes.
FW MODEMUTE.
2. Press the FM MODE/MUTE button on the Tuner to the AUTO mode
to receive the station In stereo.
*
If a stereo broadcast is received when the FM band is selected, the
"STEREO" light will be displayed on the Tuner.
*
If the FM Reception Mode is MONO, the "STEREO" light will not be
displayed.
Advertisement
Table of Contents
