Paradyne COMSPHERE 3610 Quick Reference Manual
Data service units dial backup module
Hide thumbs
Also See for COMSPHERE 3610:
- Operator's manual (310 pages) ,
- Application manual (238 pages) ,
- User manual (112 pages)
Related Manuals for Paradyne COMSPHERE 3610
Summary of Contents for Paradyne COMSPHERE 3610
- Page 1 COMSPHERE 3600 SERIES DATA SERVICE UNITS DIAL BACKUP MODULE QUICK REFERENCE Document No. 3610-A2-GL13-00...
-
Page 2: Document Feedback
Copyright E 1998 Paradyne Corporation. All rights reserved. Printed in U.S.A. Notice This publication is protected by federal copyright law. No part of this publication may be copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form or by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the express written permission of Paradyne Corporation, 8545 126th Ave. -
Page 3: Read First
Follow these steps for a successful installation of your DBM. 1. If required, install new firmware. The 3600 Series DBM Option Installation Instructions , Document No. 3610-A2-GZ52, explains how to determine whether it is required. 2. Verify the switch settings on the DSU. - Page 4 Powering Up the DBM When you apply power to the DSU, the DSU performs a power-up routine and: Determines what hardware options are installed, including a DBM. Automatically runs a Device Test (Devic) on the DSU and each installed hardware option.
-
Page 5: Network Verification Testing
Network Verification Testing Perform verification testing after any installation. Refer to the Network Verification Testing section of the User’s Guide for more information. After confirming the network connection for a DSU equipped with a DBM: " Procedure 1. Use the Dial command to establish a dialed call to the remote unit in order to: —... -
Page 6: Status Branch
Status Branch The Status (Stat) branch includes reports on the: Health and status of the DSU, DBM, TDM, and MCMP DTE interface Local Bckup Stat DTE CircQ Port Select Devic Expan Subn Backup Branch The Backup (Bckup) branch controls operation of the dial backup feature for DBMs. The Bckup selection is used to control DBM dialing from the front panel. -
Page 7: Test Branch
The Configuration (Confg) branch allows you to configure or customize the DSU and the DBM options. Change configurations options from either: A front panel A 6700 or 6800 Series NMS An asynchronous terminal (3610 standalone only) TOP-LEVEL MENU Remot Msgs... - Page 8 TOP-LEVEL MENU Remot Local Address Stat Bckup Test Confg Opts PList Phone Addr Chang Clr Displ Chang Chang Clr Activ Skip Delet Save Chang Clr Load Activ Remt Usr1 Usr3 Usr2 Address Activ Usr1 Usr2 Usr3 SAVE Diag Activ Remt Usr1 Usr2 Usr3...
-
Page 9: Configuration Option Tables
Configuration Option Tables In the tables that follow, FacT (Factory Tributary) defaults are shown in boldface. If different from the FacT defaults, FacC (Factory Control) defaults are shown in italics . Key to symbols: Configuration options that do not appear when Full mode is disabled using Menu from the Configuration branch. - Page 10 Diagnostic General Configuration Options Cntrl , Trib, G2Trb Position LinkConfg Pt-Pt, M-Pt A 1, 2, 10 Resp Period A 0:10 (5 sec to 10 min) TribTimOut Diag Conn CC, DC A 0s, 1s, 2s, 5s, 10s, 20s, 50s Link Delay A 0s, 1s, 2s, 5s, 10s, 20s, 50s Network Delay A 0s, 1s...
-
Page 11: Dbm Configuration Options
DBM Configuration Options Configuration Options Rate(Kbps) } 64, 56, 28.8, 26.4, 24.0, 21.6, 19.2, 16.8, 14.4, 12.0, 9.6, 7.2, 4.8, 2.4 PrtSp(Kbps) } 64, 56, 48, 38.4, 32, 28.8, 26.4, 24.0, 21.6, 19.2, 18.8, 18.0, 16.8, 14.4, 12.0, 9.6, 9.2, 8.4, 7.2, 4.8, 4.4, 4.0, 2.4, 2.0, 1.2, Disab LL }} Int , RXC, DSU, Prt1, Prt2, Prt3, Prt4, Prt5, Prt6 TxClkSource... - Page 12 Backup Configuration Options Auto Bckup Enab, Disab Backup Dir 1–10 FAOnCMI Enab, Disab AutoRestor Enab, Disab NtwkTimOut 1:00, 0:20 (1 sec to 30 min) RestorTimOut 5 min (1 min to 60 min) TriesTimeOut 15 min (1 min to 60 min) MultiCall Enab, Disab DBM PrtSp...
-
Page 13: Control Branch
Control Branch The Control (Ctrl) branch allows you to: Enable or disable the DSU’s and/or DBM’s transmitter. DBM alarms can be halted by disabling the DBM. Select LEDs to be displayed. Display/change the status of general purpose external DTE leads. Initiate a full device reset and power-up routine using Reset. - Page 14 Software and Firmware Version Control Verify that the control and tributary DSUs have the same firmware version or that the control has the highest firmware version. If the control DSU software version is less than 7.24 but greater than 1.10, changes are required to the DSU tributary firmware version in the General configuration options.