Advertisement
Quick Links
Specifications
• Handmade in Italy since 1960
• ¼ Turn valves handmade at
Nicolazzi Factory
• Lead Free Brass Compliant to
AZ/NZS 3718
• Suitable even and uneven
pressure
• Handles are interchangeable
Further information Phone (03) 9761 4603
Basin single-hole mixer with swivel spout
Art: Z2236--27
Available replacement
handles:
-
27 Monte Carlo Handle
-
29 Mac Kinley 05 Handle
WM22315
AS/NZS3662
Canterbury Sink & Tap Co.
Max/Min Operating
Pressure: 100/500kPa
sales@sinkandtap.com.au
Advertisement
Related Manuals for CANTERBURY OFFICINA NICOLAZZI Z2236-27
Summary of Contents for CANTERBURY OFFICINA NICOLAZZI Z2236-27
- Page 1 • ¼ Turn valves handmade at Nicolazzi Factory • Lead Free Brass Compliant to AZ/NZS 3718 • Suitable even and uneven pressure WM22315 AS/NZS3662 • Handles are interchangeable Canterbury Sink & Tap Co. Max/Min Operating Pressure: 100/500kPa Further information Phone (03) 9761 4603 sales@sinkandtap.com.au...
- Page 2 Important Notice Model : Z2236--27 CAREFULLY READ THROUGH THESE INSTRUCTIONS BEFORE INSTALLATION AND USE OF ALL TAP WARE AND WALL VALVES INSTALLATION and WARRANTY INSTRUCTIONS TECHNICAL INFORMATION All flexible hoses are designed and manufactured for use with water in exposed locations only. Do not expose to household cleaners, chlorine, chloride, hydrochloric acid or other corrosive chemicals.
- Page 3 Installation Instructions Model : Z2236--27 ❶ Preparation Tap body Flush out the pipework to remove any foreign matter. Tap body cut out hole sizes : Maximum 33mm diameter. Under side clearance : Maximum 55mm ❷ Install the pop-up waste body top section 1, and waste body bottom section 4, to the basin as shown.
- Page 4 Installation Instructions Model : Z2236--27 ❸ Install the water supply hose 6, into tap the body 5. - Note: Hand tighten only, DO NOT over tighten- 6! ❹ Install the second water supply hose 7, on to tap body 5. - Note: Hand tighten the supply hose only, DO NOT over tighten- 7! ❺...
- Page 5 Installation Instructions Model : Z2236--27 ❻ Feed the O-ring 9, over the water supply hoses. Note: Feed the water supply hoses through the cut out hole, ensuring that they are not bent or kinked, as this could result in permanent damage or leakage.
-
Page 6: Installation Instructions
Installation Instructions Model : Z2236--27 Install the vertical waste pop-up rod 13, by Check the position of the tap on the counter top, ❽ ❾ feeding it through the hole in the top of the tap and then tighten the nut using a 13mm spanner or body. - Page 7 Spare Parts list Model : Z2236 Further information Phone (03) 9761 4603 sales@sinkandtap.com.au...
- Page 8 Spare Parts list Model : Z2236 Further information Phone (03) 9761 4603 sales@sinkandtap.com.au...
- Page 9 Care and Maintenance Instructions Model : Z2236--27 Removing and replacing a handle MODEL SHOWN :Z2236 ❶ ❷ Loosen and unscrew the retaining flange Once totally loose, simply remove the A, from the tap body. handle from cartridge spline. ...
- Page 10 Care and Maintenance Instructions Model : Z2236--27 MAINTENANCE FOR ONE HOLE/TWO LEVER TAP WARE WITH TWO LEVER DESIGN INSTRUCTIONS FOR REPLACEMENT OF THE HOT OR COLD CARTRIDGE Do not replace the cartridge if there is low flow or no flow. Low flow or no flow is caused by obstruction or kinking of supply hoses.
- Page 11 Care and Maintenance Instructions Model : Z2236--27 LOW FLOW OR NO FLOW TROUBLESHOOTING INSTRUCTIONS Current bathroom taps have a max flow rate of 7 Litres per minute from the aerator and the hand spray. If you are experiencing low flow from the spout: Do not change the cartridge •...
- Page 12 Care and Maintenance Instructions Model : Z2236--27 Care of external finishes Nicolazzi products are all authentic finishes that have not been coated with any product. After each use, pat the fixture down to remove any excess water. This will prevent any water spotting or mineral build-up. Use only soft liquid soap and water to clean the surface.