Summary of Contents for LG 60PM4M - - 60" Plasma Panel
Page 1
MODELS: 42PM4M 50PM4M 60PM4M OWNER'S MANUAL P_ease read this manua_ carefully before operating your set. Retain it for future reference. Record model number and seria_ number of the set. See the label attached on the back cover and quote this information to your dealer when you require service.
Page 2
CAUTION: Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized mod- ification could void the user's warranty. COMPLIANCE: The responsible party for this product's compliance is: LG Electronics U.S.A., Inc...
Safety Instructions IMPORTANT SAFETY INSTRUCTIONS Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the appa- ratus.
Page 4
Safety Instructions 12. Use only with the cart, stand, tripod, bracket, or table 15. CAUTION concerning the Power Cord : specified by the manufacturer, or sold with the apparatus. Most appliances recommend they be placed upon a dedi- When a cart is used, caution when...
Introduction I 0 n What is a Plasma Display Panel? If voltage is applied to a gas within glass panels, ultraviolet rays are produced and fused with a fluorescent substance. At that instant, light is emitted. A Plasma Display is the a next generation flat Display using this phenomenon. 160 °...
Introduction Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product. Owner's Manual Batteries Remote Control Power Cord Optional extras can be changed or modified for quality improvement without any notification new optional extras can be added.
Page 8
Introduction C0 nt - Here shown may be somewhat different from your set. 1. Power Indicator 4. VOLUME (_', _,) Buttons Illuminates red in standby mode, Illuminates green when the Set is turned on. 5. MENU Button 6. iNPUT SELECT Button 2.
Page 9
Introduction Connection Options - Here shown may be somewhat different from your set. REMOTE CONTROLIN AV IN S-VIDEO/AUDIO IN SOCKETS Connect the S-VIDEO out socket of an VCR to the S-VIDEO RS-232C INPUT(CONTROL&SERVICE) PORT socket. Connect to the RS-232C port on a PC. Connect the audio out sockets of the VCR to the audio sock- HDMI/DVI IN ets as in AV.
Introduction Remote Control Key Functions When using the remote control, aim it at the remote control sensor on the monitor. Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function. Press the key again as necessary. AV buttons POWER Each time you press the Input but-...
Page 11
Installation Ilation Instal lation Instru ction s • Install this monitor only in a location where adequate ventilation is available. • If set is installed vertically, it is on the control key toward down. GROUNDING Power Supply Ensure that you connect the grounding / earth wire to prevent possible electric shock.
Page 12
Installation Equipment Connections NOTE: Not all cables shown are included with the plasma display, 1. First of all, see if the computer, product and the peripherals are turned off. Then, connect the signal input cable. a. When connecting with the D-Sub signal input cable. Rear side of the product.
Page 13
Installation 4. Turn on power by pressing the power button on the product. Turn on the PC. 5. Select an input signal. Press the INPUT button on the remote control to select the input signal. INPUT_ A /• a. When connecting with a D-Sub signal input cable. •...
Page 14
Installation 1. Connect the video cable as shown in the below figure and then connect the power cord. a. When connecting with a BNC cable. b. When connecting with a S-Video cable. • Connect the input terminal with a proper colour match. •...
Page 15
Installation 1. Connect the video/audio cable as shown in the below figure and then, connect the power cord. • Connect the input terminal with a proper colour match. Product Product Audio Cable BNC Cable (not included) BNC Cable Audio Cable (not included (not included) (not included)
Page 16
Installation • When you set the input signal of the main screen as 'AV (CVBS)', you can transmit the signal that you're watching to the AV output terminal. Video/TV \udio Cable (not included) i not included) Product Audio Cable (not included) (not included) Video/TV NOTES:...
Page 17
Operation Your Monitor's OSD (On Screen Display) may differ slightly from what is shown in this manual. on the 1. Connect power cord correctly. At this moment, the Monitor is switched to standby mode. 2. Press the INPUT or (b button on the Monitor or press the POWER, INPUT button on the remote control and then the Monitor will switch on.
Operation Pi ct u re 0 pt io ns - Readjust Picture menu settings for each following input source as preferred. This function adjusts the set to the best picture appearance. When adjusting picture options (contrast, brightness, colour, sharpness and tint (NTSC input only)) manually, PSM is automatically changed to User.
Page 19
Red, Green and Blue is -40 - +40. 6. Press the EXIT button to save the new settings. XD is LG electronic's unique picture improving technology to display a real HD source through an advanced digital signal processing algorithm.
Operation Pic:ture Menu Options - Set up the monitor for the best picture appearance for viewing movies. - This feature operates only in AV, S-Video and Component 480i/576i mode. b> 1. Press the MENU button and then use A / • button to select the PICTURE menu.
Operation Sound Opt:ions This function lets you enjoy the best sound without any special adjustment because the set automatically selects the appropriate sound option based on the program content. _SurroundMAxl____ I FlatI--_1Music I---_1 Movie I---_1 Sports I--_1 User I __ I •...
Page 22
Operation Me nu 0 pt io ns 1. Press the MENU button and then use A / • button to select the SOUND menu, 2, Press the l,- button and then use A / • button to select B_ance, 3, Press the l,- button and then use "_ / l,- button to make appropriate adjustments, 4, Press the EXIT button to save the new settings, 1, Press the MENU button and then use A / •...
Page 23
Operation M e n u 0 pt i o n s If current time setting is wrong, correct the clock setting. b> 1. Press the MENU button and then use A / • button to select the TIME menu. 2. Press the IP- button and then use A / • button to select Clock. 3.
Page 24
Operation Timer Menu Options - If there is no input signal, the Monitor turns off automatically after 10 minutes, 1, Press the MENU button and then use A / • button to select the TIME menu, 2, Press the IP- button and then use A / • button to select Auto sleep, 3, Press the IP- button and then use A / •...
Page 25
Operation Special Opt:ions The monitor can be set up so that it can only be used with the remote control. This feature can be used to prevent unauthorized viewing by disabling the front panel controls. This Monitor is programmed to remember which option it was last set to even if you turn the monitor off. 1.
Page 26
Operation Options • Tile Mode Tile mode and choose Tile alignment and set the ID of the current product to set location, It is used to enlarge the screen and also used with several products to view screen. b> * Only after pressing the SET button the adjustments made to the settings will be saved, - Tile mode : row x column ( r = 1,2, 3, 4 c = 1, 2, 3, 4) - 4 x 4 available, - Configuration...
Page 27
Operation - Tile mode (product 1 - 2) : r(2) x c(1 ) olumn b> Press the MENU button and then use A / • button to select the SPECIAL menu. 2. Press the IP-button and then use A / • button to select Tile mode.
Page 28
Operation Me nu 0 pt io ns Use it to see the difference between XD Demo on and XD Demo off, It's not available to use this function in RGB[PC], HDMI[PC] mode, b> 1, Press the MENU button and then A/• button to select the SPECIAL menu, 2, Press the 1_ button and then use A / •...
Page 29
Operation Automatically adjusts picture position and minimizes image shaking. This function works in the following mode : RGB[PC]. b> 1. Press the MENU button and then use A / • button to select the SCREEN menu. 2. Press the 1_ button and then use A / •...
Page 30
Operation Menu ODt:ions To see a normal picture, match the resolution of RGB mode and selection of XGA mode. This function works in the following mode : RGB[PC] b> 1. Press the MENU button and then use A / • button to select the SCREEN menu.
Page 31
Operation HDMI/DVl MODE component Spectacle Full Original 16:9 14:9 Zoom1 Zoom2 This function operates in current mode. To initialize the adjusted value 1. Press the MENU button and then A / • button to select the SCREEN menu. 2. Press the I,- button and then A / • button to select Reset.
Page 32
External Control Device Setup Set:up - Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitor's functions externally. - Connect the serial port of the control device to the RS-232C jack on the Monitor back panel. - RS-232C connection cables are not supplied with the Monitor.
Extemal Control Device Setup - Use this function to specify a monitor ID number. - Refer to 'Real Data Mapping 1'. See page 35. b> 1. Press the MENU button and then use the A / • button to select the SPECIAL menu. 2.
External Control Device Setup 01. Power (Command 2:a) 04. Screen Mute (Command 2:d) I_ To control Power On/Off of the Monitor. I_ To select screen mute on/off. Transmission Transmission [[k][a][ ][Set IU][ ][Uata][Cr] [[k][d][ ][Set IU][ ][Uata][Cr] Data 0 : Power Off 1 : Power On Data 0 : Screen mute off (Picture on) 1 : Screen mute on (Picture off)
Page 35
External Control Device Setup 07. Contrast (Command 2:g) 10. Tint (Command2:j) (Video only) I_ To adjust screen contrast. I_ To adjust the screen tint. You can also adjust contrast in the picture menu. You can also adjust tint in the Picture menu. Transmission Transmission [[k][g][...
Page 36
External Control Device Setup 14. Balance (Command2:t) 18. Auto Configure (Command: i u) I_ To adjust balance. I_ To adjust picture position and minimize image shaking Transmission automatically. Auto Configure only works in RGB-PC mode. I[k][t][ ][Set IU][ ][Uata][Cr] Transmission Data Mini 0 - Max: 64 I[j][u][...
Page 37
External Control Device Setup 24. Natural Mode (In Tile mode) (Command : d j) 21. Tile H Size(Command : d g) I_ To set the Horizontal size. I_ The image is omitted by the distance between the screens to be naturally shown. Transmission Transmission i[d][g][ ][Set IU][ ][Uata][x]...
IRCode Connect your wired remote control to the Remote Control port on the Monitor. Output waveform Single pulse, modulated with 37.917KHz signal at 455KHz Carrier frequency m_--]mJmlm FCAR = 1/70 = fOSC/12 I_-t T1 Duty ratio = T1/Tc = 1/3 Configuration of frame o 1st frame...
Page 39
IRCode Function Note Code (Hexa) Number Key O R!C Button R!C Button Number Key 1 Number Key 2 R!C Button Number Key 3 R!C Button R!C Button Number Key 4 R!C Button Number Key 5 R!C Button Number Key 6 R!C Button Number Key 7 Number Key 8...
Troubleshooting Checklist Tr oubIeshoot ing where the Monitor's power cord was plugged in Press the VOLUME (I_) button. Picture OK & osoun Sound muted? Press MUTE button. • Check to see if there is any object between the Plasma Display and the remote control causing obstruction.